Kelli A. Agee

Effects of Sodium Hypochlorite and RC-Prep on Bond Strengths of Resin Cement to Endodontic Surfaces

There is concern that the use of sodium hypochlorite (NaOCl) and RC-Prep may lower the bond strength of resin cements. The objective of this study was to evaluate the effect of 5% NaOCl and RC-Prep treatment on the bond strength of a resin cement, C&B Metabond. Control roots (group 1) were biomechanically prepared using 0.9% NaCl as an irrigant; group 2, roots with 5% NaOCl; group 3, roots with RC-Prep; group 4, roots with 0.9% NaCl followed by 10% ascorbic acid; group 5, roots with 5% NaOCl followed by 10% ascorbic acid (pH 4); group 6, roots with 5% NaOCl followed by 10% neutral sodium ascorbate; and group 7, roots with RC-Prep followed by 10% ascorbic acid. All roots were then filled with C&B Metabond, incubated in water for 24 h, and then cross-sectioned into six 1-mm thick slabs representing cervical and middle root dentin. The slabs were trimmed and tested for tensile bond strength. The results demonstrated that both 5% NaOCl and RC-Prep produced significantly (p < 0.05) large reductions in resin-dentin bond strengths, and the reductions could be completely reversed by the application of either 10% ascorbic acid or 10% sodium ascorbate.

Effects of one versus two applications of an unfilled, all-in-one adhesive on dentine bonding

OBJECTIVES This study examined the null hypothesis that there is no difference between the effect of a one versus two-layer applications of Prompt L-Pop (3M ESPE, Seefeld, Germany) to sound, abraded human coronal dentine. METHODS In group I, the mixed adhesive was applied for 15s, and light-cured for 10s. In group II, after light-curing the first layer, the adhesive was re-applied and light-cured. Specimens bonded with a hybrid composite were sectioned into beams for microtensile bond strength evaluation. Additional teeth from each group were bonded similarly using a lining composite for transmission electron microscopy examination of the resin-dentine interfaces, and nanoleakage evaluation using ammoniacal silver nitrate. RESULTS A significant difference (p<0.001) was detected between microtensile bond strengths in the two groups. Stained, demineralized sections revealed 3-5 microm thick hybrid layers in both groups. An electron-lucent layer between 7 and 20 microm thick was present between the adhesive and the overlying composite. This layer was absent from the interfaces after removal with ethanol before composite placement. The use of a single application in group I resulted in the direct contact of the electron-lucent layer with the dentine surface and tubular orifices. In unstained, undemineralized sections used to evaluate nanoleakage, silver deposits were found mostly in the hybrid layer in group II, but throughout the entire adhesive layer in group I. CONCLUSION Bonding of this unfilled all-in-one adhesive to dentine may be improved by application of a second adhesive layer after light-curing the first layer. This ensures that the exposed dentine surface and dentinal tubules are coated with adhesive that is adequately polymerized.

Host-derived loss of dentin matrix stiffness associated with solubilization of collagen.

Matrix metalloproteinases (MMPs) bound to dentin matrices are activated during adhesive bonding procedures and are thought to contribute to the progressive degradation of resin-dentin bonds over time. The purpose of this study was to evaluate the changes in mechanical, biochemical, and structural properties of demineralized dentin treated with or without chlorhexidine (CHX), a known MMP-inhibitor. After demineralizing dentin beams in EDTA or phosphoric acid (PA), the baseline modulus of elasticity (E) of each beam was measured by three-point flexure. Specimens were pretreated with water (control) or with 2% CHX (experimental) and then incubated in artificial saliva (AS) at 37 degrees C for 4 weeks. The E of each specimen was remeasured weekly and, the media was analyzed for solubilized dentin collagen at first and fourth week of incubation. Some specimens were processed for electron microscopy (TEM) immediately after demineralization and after 4 weeks of incubation. In EDTA and PA-demineralized specimens, the E of the control specimens fell (p < 0.05) after incubation in AS, whereas there were no changes in E of the CHX-pretreated specimens over time. More collagen was solubilized from PA-demineralized controls (p < 0.05) than from EDTA-demineralized matrices after 1 or 4 weeks. Less collagen (p < 0.05) was solubilized from CHX-pretreated specimens demineralized in EDTA compared with PA. TEM examination of control beams revealed that prolonged demineralization of dentin in 10% PA (12 h) did not denature the collagen fibrils.

The requirement of zinc and calcium ions for functional MMP activity in demineralized dentin matrices

UNLABELLED The progressive degradation of resin-dentin bonds is due, in part, to the slow degradation of collagen fibrils in the hybrid layer by endogenous matrix metalloproteinases (MMPs) of the dentin matrix. In in vitro durability studies, the storage medium composition might be important because the optimum activity of MMPs requires both zinc and calcium. OBJECTIVE This study evaluated the effect of different storage media on changes in matrix stiffness, loss of dry weight or solubilization of collagen from demineralized dentin beams incubated in vitro for up to 60 days. METHODS Dentin beams (1mm×2mm×6mm) were completely demineralized in 10% phosphoric acid. After baseline measurements of dry mass and elastic modulus (E) (3-point bending, 15% strain) the beams were divided into 5 groups (n=11/group) and incubated at 37°C in either media containing both zinc and calcium designated as complete medium (CM), calcium-free medium, zinc-free medium, a doubled-zinc medium or water. Beams were retested at 3, 7, 14, 30, and 60 days of incubation. The incubation media was hydrolyzed with HCl for the quantitation of hydroxyproline (HOP) as an index of solubilization of collagen by MMPs. Data were analyzed using repeated measures of ANOVA. RESULTS Both the storage medium and the storage time showed significant effects on E, mass loss and HOP release (p<0.05). The incubation in CM resulted in relatively rapid and significant (p<0.05) decreases in stiffness, and increasing amounts of mass loss. The HOP content of the experimental media also increased with incubation time but was significantly lower (p<0.05) than in the control CM medium, the recommended storage medium. CONCLUSIONS The storage solutions used to age resin-dentin bonds should be buffered solutions that contain both calcium and zinc. The common use of water as an aging medium may underestimate the hydrolytic activity of endogenous dentin MMPs.

Effects of Resin Hydrophilicity on Dentin Bond Strength

The purpose of this study was to determine if hydrophobic resins can be coaxed into dentin wet with ethanol instead of water. The test hypothesis was that dentin wet with ethanol would produce higher bond strengths for hydrophobic resins than would dentin wet with water. This study examined the microtensile bond strength of 5 experimental adhesives (50 wt% ethanol/50% comonomers) of various degrees of hydrophilicity to acid-etched dentin that was left moist with water, moist with ethanol, or air-dried. Following composite buildups, hourglass-shaped slabs were prepared from the bonded teeth for microtensile testing. For all 3 types of dentin surfaces, higher bond strengths were achieved with increased resin hydrophilicity. The lowest bond strengths were obtained on dried dentin, while the highest bond strengths were achieved when dentin was bonded moist with ethanol. Wet-bonding with ethanol achieved higher bond strengths with hydrophobic resins than were possible with water-saturated matrices.

Substantivity of chlorhexidine to human dentin

OBJECTIVES To better comprehend the role of CHX in the preservation of resin-dentin bonds, this study investigated the substantivity of CHX to human dentin. MATERIAL AND METHODS Dentin disks (n=45) were obtained from the mid-coronal portion of human third molars. One-third of dentin disks were kept mineralized (MD), while the other two-thirds had one of the surfaces partially demineralized with 37% phosphoric acid for 15 s (PDD) or they were totally demineralized with 10% phosphoric acid (TDD). Disks of hydroxyapatite (HA) were also prepared. Specimens were treated with: (1) 10 microL of distilled water (controls), (2) 10 microL of 0.2% chlorhexidine diacetate (0.2% CHX) or (3) 10 microL of 2% chlorhexidine diacetate (2% CHX). Then, they were incubated in 1 mL of PBS (pH 7.4, 37 degrees C). Substantivity was evaluated as a function of the CHX-applied dose after: 0.5 h, 1 h, 3 h, 6 h, 24 h, 168 h (1 week), 672 h (4 weeks) and 1344 h (8 weeks) of incubation. CHX concentration in eluates was spectrophotometrically analyzed at 260 nm. RESULTS Significant amounts of CHX remained retained in dentin substrates (MD, PPD or TDD), independent on the CHX-applied dose or time of incubation (p<0.05). High amounts of retained CHX onto HA were observed only for specimens treated with the highest concentration of CHX (2%) (p<0.05). CONCLUSION The outstanding substantivity of CHX to dentin and its reported effect on the inhibition of dentinal proteases may explain why CHX can prolong the durability of resin-dentin bonds.

The Inhibitory Effects of Quaternary Ammonium Methacrylates on Soluble and Matrix-bound MMPs

Matrix metalloproteinases (MMPs) bound to dentin contribute to the progressive degradation of collagen fibrils in hybrid layers created by dentin adhesives. This study evaluated the MMP-inhibiting potential of quaternary ammonium methacrylates (QAMs), with soluble rhMMP-9 and a matrix-bound endogenous MMP model. Six different QAMs were initially screened by a rhMMP-9 colorimetric assay. For the matrix-bound endogenous MMPs, we aged demineralized dentin beams for 30 days in calcium- and zinc-containing media (CM; control), chlorhexidine, or QAMs in CM to determine the changes in dry mass loss and solubilization of collagen peptides against baseline levels. The inhibitory effects of QAMs on soluble rhMMP-9 varied between 34 and 100%. Beams incubated in CM showed a 29% decrease in dry mass (p < 0.05), whereas beams incubated with QAMs showed only 0.2%-6% loss of dry mass. Significantly more solubilized collagen was detected from beams incubated in CM (p < 0.05). It is concluded that QAMs exhibited dentin MMP inhibition comparable with that of chlorhexidine, but required higher concentrations.

Solvent-induced dimensional changes in EDTA-demineralized dentin matrix

The purpose of this study was to test the null hypothesis that the re-expansion of dried matrix and the shrinkage of moist, demineralized dentin is not influenced by polar solvents. Dentin disks were prepared from midcoronal dentin of extracted human third molars. After complete demineralization in 0.5M of EDTA (pH 7), the specimens were placed in the well of a device that measures changes in matrix height in real time. Dry, collapsed matrices were created by blowing dry N(2) on the specimens until they shrank to a stable plateau. Polar solvents [water, methanol, ethanol, n-propanol, n-butanol, formamide, ethylene glycol, hydroxyethyl methacrylate (HEMA), or mixtures of water-HEMA] as model primers then were added and the degree of re-expansion measured. These same solvents also were applied to moist, expanded matrices and the solvent-induced shrinkages measured. Regression analysis was used to test the correlations between matrix height and Hansens dispersive, polar, hydrogen bonding, and total solubility parameters (delta(d), delta(p), delta(h), delta(t)). The results indicate that water-free polar solvents of low hydrogen bonding (H-bond) ability (e.g., neat HEMA) do not re-expand dried matrices and that they shrink moist matrices. When HEMA was mixed with progressively higher water concentrations, the model water-HEMA primers expanded the dried matrix in proportion to their water concentrations and they produced less shrinkage of moist matrices. Solvents with higher H-bonding capacities (methanol, ethanol, ethylene glycol, formamide, and water) re-expanded the dried matrix in proportion to their solubility parameters for H-bonding (delta(h)). They also induced small transient shrinkages of moist matrices, which slowly re-expanded. The results require rejection of the null hypothesis.

Chlorhexidine binding to mineralized versus demineralized dentin powder

OBJECTIVES The purposes of this work were to quantitate the affinity and binding capacity of chlorhexidine (CHX) digluconate to mineralized versus demineralized dentin powder and to determine how much debinding would result from rinsing with water, ethanol, hydroxyethylmethacrylate (HEMA) or 0.5M NaCl in water. METHODS Dentin powder was made from coronal dentin of extracted human third molars. Standard amounts of dentin powder were tumbled with increasing concentrations of CHX (0-30 mM) for 30 min at 37 degrees C. After centrifuging the tubes, the supernatant was removed and the decrease in CHX concentration quantitated by UV-spectroscopy. CHX-treated dentin powder was resuspended in one of the four debinding solutions for 3 min. The amount of debound CHX in the solvents was also quantitated by UV-spectroscopy. RESULTS As the CHX concentration in the medium increased, the CHX binding to mineralized dentin powder also increased up to 6.8 micromol/g of dry dentin powder. Demineralized dentin powder took up significantly (p<0.01) more CHX, reaching 30.1 micromol CHX/g of dry dentin powder. Debinding of CHX was in the order: HEMA<ethanol<0.05 M NaCl<water. The highest CHX binding to demineralized dentin occurred at 30 mM (1.5 wt.%). SIGNIFICANCE As CHX is not debound by HEMA, it may remain bound to demineralized dentin during resin-dentin bonding. This may be responsible for the long-term efficacy of CHX as an MMP inhibitor in resin-dentin bonds.

Durability of Resin-Dentin Bonds to Water- vs. Ethanol-saturated Dentin

Higher 24-hour resin-dentin bond strengths are created when ethanol is used to replace water during wet bonding. This in vitro study examined if ethanol-wet-bonding can increase the durability of resin-dentin bonds over longer times. Five increasingly hydrophilic experimental resin blends were bonded to acid-etched dentin saturated with water or ethanol. Following composite build-ups, the teeth were reduced into beams for 24-hour microtensile bond strength evaluation, and for water-aging at 37°C for 3, 6, or 12 months before additional bond strength measurements. Although most bonds made to water-saturated dentin did not change over time, those made to ethanol-saturated dentin exhibited higher bond strengths, and none of them fell over time. Decreased collagen fibrillar diameter and increased interfibrillar spacing were seen in hybrid layers created with ethanol-wet-bonding. Increases in bond strength and durability in ethanol-wet-bonding may be due to higher resin uptake and better resin sealing of the collagen matrix, thereby minimizing endogenous collagenolytic activities.