Kristian Nielsen

Zeonex-PMMA microstructured polymer optical FBGs for simultaneous humidity and temperature sensing

In this Letter, we report for the first time, to the best of our knowledge, the fabrication and characterization of a Zeonex/PMMA microstructured polymer optical fiber (mPOF) Bragg grating sensor for simultaneous monitoring of relative humidity (RH) and temperature. The sensing element (probe) is based on two separate in-line fiber Bragg gratings (FBGs) inscribed in the fabricated mPOF. A root mean square deviation of 0.8% RH and 0.6°C in the range of 10%-90% RH and 20°C-80°C was found. The developed mPOFBG sensor constitutes an efficient route toward low-cost, easy-to-fabricate and compact multi-parameter sensing solutions.

Fast Inscription of Long Period Gratings in Microstructured Polymer Optical Fibers

We demonstrate 20 dB long period grating (LPG) fast inscription in microstructured polymer optical fibers (mPOFs) using a point-by-point technique obtaining an LPG total length of 25 mm. Two 248 nm UV laser pulses of 15 ns duration have been employed for every inscription point, which means a time reduction by over 21 times compared with the fastest inscription time already reported in literature. The device has been fabricated in a single-mode mPOF with a core that has been doped with benzyl dimethyl ketal for photosensitivity enhancement. Moreover, we characterize the strain and temperature responses and the stability of the fabricated gratings response under different conditions in order to assess the viability for different applications.

Long-term strain response of polymer optical fiber FBG sensors

We report on the viscoelastic response of PMMA microstructured polymer optical fibers (mPOFs) when exposed to long periods of strain and relaxation, with the strain period ranging from 0.5 min to 50 min. The behavior of the fibers was monitored by inscribing a fiber Bragg grating (FBG) in them and tracking the reflection peak. We demonstrate that the fiber, when relaxing from strains of up to 0.9%, has a two-phase recovery: initially linear (elastic driven) and subsequently nonlinear (viscoelastic driven) contraction. The linear (elastic) relaxation wavelength range depends both on the strain level and on the strain duration. For short strain durations, this wavelength range stays the same, but with increasing strain duration, it decreases, which will influence the operation range of mPOF and POF-based FBG sensors.

Fast and stable gratings inscription in POFs made of different materials with pulsed 248 nm KrF laser

This paper presents fiber Bragg grating (FBG) inscription with a pulsed 248 nm UV KrF laser in polymer optical fibers (POFs) made of different polymers, namely polymethyl methacrylate (PMMA), cyclic-olefin polymer and co-polymer, and Polycarbonate. The inscribed gratings and the corresponding inscription parameters are compared with grating inscribed in POFs made of the aforementioned materials but with the hitherto most used laser for inscription, which is a continuous wave 325 nm UV HeCd laser. Results show a reduction of the inscription time of at least 16 times. The maximum time reduction is more than 130 times. In addition, a reflectivity and a bandwidth close to or higher than the ones with the 325 nm laser were obtained. The polymer optical fiber Bragg gratings (POFBGs) inscribed with the 248 nm laser setup present high stability with small variations in their central wavelength, bandwidth, and reflectivity after 40 days.

Effects of pre-strain on the intrinsic pressure sensitivity of polymer optical fiber Bragg-gratings

We experimentally demonstrate a scheme for improving the intrinsic pressure sensitivity of fiber Bragg-gratings (FBGs) inscribed in polymer optical fibers by applying pre-strain in order to suppress the pressure induced mechanical contraction of the fiber. This contraction would otherwise contribute to a blueshift of the Brag-wavelength, counteracting the dominant redshift caused by the stress-optic effect, which effectively reduces the pressure sensitivity of the FBG. By applying this technique we are able to improve the sensitivity of the FBG from 2.8 pm/bar to 7.3 pm/bar.

Simultaneous measurement of temperature and humidity with microstructured polymer optical fiber Bragg gratings

A microstructured polymer optical fiber (mPOF) Bragg grating sensor system for the simultaneous measurement of temperature and relative humidity (RH) has been developed and characterized. The sensing head is based on two in-line fiber Bragg gratings recorded in a mPOF. The sensor system has a root mean square deviation of 1.04 % RH and 0.8 °C in the range 10 to 90% RH and 20 to 80 °C. The proposed sensor system is easy to fabricate, cheap and compact.

NUMERICAL PREDICTION OF WAVE IMPACT LOADS ON MULTIPLE RECTANGULAR BEAMS

Wave impact on one and two structural beams with rectangular cross section is simulated with a two-dimensional finite volume method, solving the unsteady Euler equations and employing a VOF-type method for the description of the free surface. Four different test series are carried out, each corresponding to a wave impact scenario in the experimental database of Sterndorff [2002]. For the case of wave impact on a single structural element the numerical results show good agreement, with measured force time histories. In the computations featuring two beams, the prediction of the shadowing effect of the first beam on the second is in reasonable agreement with the experimental data. However, the force peak on the second beam is somewhat over-predicted. The calculations successfully predict a second peak in the force time series of the second beam, which is caused by airborne water shipped over the first beam. Throughout the work, spurious spikes of very short duration appear in the computed load time series, originating from the changing of the flow separation location along the lower edge of the beams.