Ksenija Zelic

Mechanical weakening of devitalized teeth: three-dimensional Finite Element Analysis and prediction of tooth fracture.

AIM To determine to which extent cavity preparation and each step of dentine removal in the process of root canal treatment (access cavity preparation and root canal enlargement) both individually and jointly contribute to the weakening of the tooth. METHODS Numerical analysis using finite element method (FEM) of separate and combined influence of two-surface Class II preparation and root canal treatment was undertaken to evaluate the decrease in tooth strength. The influence of the two stages in root canal treatment, access cavity preparation and root canal enlargement, was also analysed separately and jointly. After each of these phases, the crown was restored with composite resin, and the FEA was performed only on restored teeth. To estimate the influence of all these procedures on tooth fracture resistance numerically, a Failure Index based on the maximum principal stress criterion (MPCS) was applied. Compressive and tensile stresses were analysed separately and corresponding Failure Indices were calculated. RESULTS A two-surface resin composite restoration weakened the tooth by 23.25%. Nevertheless, the Failure Indices showed that this tooth was not likely to fracture even under high occlusal stress (710N). However, after access cavity preparation, the Failure Indices reached the point where, under high occlusal force that may occur in the posterior area, a tooth fracture occurred. The enlargement of root canals had an additional, but relatively small impact on tooth weakening, making the tooth even more susceptible to fracture. The combined influence of both cavity preparation and root canal enlargement led to weakening of 62.6% under a load of 710N, ultimately causing tooth fracture. CONCLUSION The combined finite element method and the maximum principal stress analysis gave insight into the fracture mechanisms of teeth with two-surface composite restorations followed by root canal preparation. Removal of tooth tissue, despite its subsequent restoration with dental materials, weakened the tooth by changing the stress intensity and distribution through tooth structures. Access cavity preparation had the greatest influence on tooth strength whilst canal enlargement did not contribute to this process substantially.

Evaluation of Facial Beauty Using Anthropometric Proportions

The improvement of a patients facial appearance is one of the main goals of contemporary orthodontic treatment. The aim of this investigation was to evaluate the difference in facial proportions between attractive and anonymous females in order to establish objective facial features which are widely considered as beautiful. The study included two groups: first group consisted of 83 Caucasian female subjects between 22 and 28 years of age who were selected from the population of students at the University of Belgrade, and the second group included 24 attractive celebrity Caucasian females. The en face facial photographs were taken in natural head position (NHP). Numerous parameters were recorded on these photographs, in order to establish facial symmetry and correlation with the ideal set of proportions. This study showed significant difference between anonymous and attractive females. Attractive females showed smaller face in general and uniformity of the facial thirds and fifths, and most of the facial parameters meet the criteria of the ideal proportions.

Accuracy of Cameriere's third molar maturity index in assessing legal adulthood on Serbian population

At the moment, a large number of asylum seekers from the Middle East are passing through Serbia. Most of them do not have identification documents. Also, the past wars in the Balkan region have left many unidentified victims and missing persons. From a legal point of view, it is crucial to determine whether a person is a minor or an adult (≥18 years of age). In recent years, methods based on the third molar development have been used for this purpose. The present article aims to verify the third molar maturity index (I3M) based on the correlation between the chronological age and normalized measures of the open apices and height of the third mandibular molar. The sample consisted of 598 panoramic radiographs (290 males and 299 females) from 13 to 24 years of age. The cut-off value of I3M=0.08 was used to discriminate adults and minors. The results demonstrated high sensitivity (0.96, 0.86) and specificity (0.94, 0.98) in males and females, respectively. The proportion of correctly classified individuals was 0.95 in males and 0.91 in females. In conclusion, the suggested value of I3M=0.08 can be used on Serbian population with high accuracy.

Influence of dental restorations and mastication loadings on dentine fatigue behaviour: Image-based modelling approach

OBJECTIVES The aim of this study was to use Finite Element Analysis (FEA) to estimate the influence of various mastication loads and different tooth treatments (composite restoration and endodontic treatment) on dentine fatigue. The analysis of fatigue behaviour of human dentine in intact and composite restored teeth with root-canal-treatment using FEA and fatigue theory was performed. METHODS Dentine fatigue behaviour was analysed in three virtual models: intact, composite-restored and endodontically-treated tooth. Volumetric change during the polymerization of composite was modelled by thermal expansion in a heat transfer analysis. Low and high shrinkage stresses were obtained by varying the linear shrinkage of composite. Mastication forces were applied occlusally with the load of 100, 150 and 200N. Assuming one million cycles, Fatigue Failure Index (FFI) was determined using Goodmans criterion while residual fatigue lifetime assessment was performed using Paris-power law. RESULTS The analysis of the Goodman diagram gave both maximal allowed crack size and maximal number of cycles for the given stress ratio. The size of cracks was measured on virtual models. For the given conditions, fatigue-failure is not likely to happen neither in the intact tooth nor in treated teeth with low shrinkage stress. In the cases of high shrinkage stress, crack length was much larger than the maximal allowed crack and failure occurred with 150 and 200N loads. The maximal allowed crack size was slightly lower in the tooth with root canal treatment which induced somewhat higher FFI than in the case of tooth with only composite restoration. CONCLUSIONS Main factors that lead to dentine fatigue are levels of occlusal load and polymerization stress. However, root canal treatment has small influence on dentine fatigue. CLINICAL SIGNIFICANCE The methodology proposed in this study provides a new insight into the fatigue behaviour of teeth after dental treatments. Furthermore, it estimates maximal allowed crack size and maximal number of cycles for a specific case.

Nano-structural and compositional basis of devitalized tooth fragility

OBJECTIVE Increased tooth fragility after devitalization is commonly observed but there is no definite mechanistic explanation for such phenomenon. Therefore, it is important to analyze more profoundly structural and compositional properties of this altered form of dentin. The present study investigates the differences between normal and devitalized dentin using advanced techniques. METHODS Atomic force microscopic imaging (AFM), energy dispersive X-ray analysis (EDX) and micro-Raman spectroscopy were performed on 16 dentin specimens, eight vital and eight that underwent root-canal treatment at least two years before extraction and had no infection in root canals before or after devitalization. RESULTS The mean size of mineral crystals showed by AFM was larger in devitalized than in healthy dentin in the same age category. AFM phase shifts in devitalized cases revealed altered mechanical characteristics and suggested differences in composition of material between devitalized teeth and healthy controls. No significant difference in Ca/P ratio between vital and devitalized teeth was found using EDX. However, micro-Raman analyses showed that in devitalized teeth, apart from hydroxyapatite, dentin contained significant amounts of apatite phases with lower calcium content: octacalcium phosphate, dicalcium phosphate dihydrate and tricalcium phosphate. SIGNIFICANCE Differences between vital and devitalized dentin bring new insights into the basis of devitalized tooth fragility. Larger mineral crystals could account for decreased mechanical strength in devitalized teeth. Moreover, calcium-phosphate phases with lower Ca content have lower material strength, and the presence of these phases in devitalized teeth may explain their increased fragility.

The third molars for indicating legal adult age in Montenegro

AIM From a medico-legal and penalty point of view, it is essential to conclude if an individual is a minor or an adult (18 years of age). Methods based on the third molar development have been used for this purpose. The present article aims to verify the Nollas stages of mineralization of the third molars and a third molar maturity index (I3M) which is based on the measures of the projections of open apices normalized by their height in the sample of Montenegrins. METHOD AND SAMPLE The sample consisted of 683 panoramic radiographs (324 males and 359 females) between 13 and 24 years of age. The specific mineralization stages of Nolla and the cut-off value of I3M < 0.08 was used to discriminate adults and minors. RESULTS The best performance in discriminating adults and minors was for I3M < 0.08 followed by the Nolla stage 9. For I3M < 0.08 the results demonstrated high sensitivity of 0.92 and 0.82 and specificity of 0.94 and 0.96 in males and females, respectively. The proportions of correctly classified individuals were 0.93 in males and 0.89 in females. The Nolla stage 9 demonstrated the sensitivity of 0.95 and 0.85 and the specificity of 0.84 and 0.90 in males and females, respectively. The proportions of correctly classified individuals were 0.90 in males and 0.87 in females. CONCLUSION The suggested value of I3M < 0.08 followed by Nolla stage 9 can be used to discriminate adults from minors with high specificity.

Forensic or archaeological issue: is chemical analysis of dental restorations helpful in assessing time since death and identification of skeletonized human remains?

In 2011, small mass grave with completely skeletonized remains was discovered in Belgrade suburb. An eyewitness claimed that skeletons belonged to German soldiers killed in WWII. Anthropologists were engaged to investigate whether the skeletal remains correspond to the indicated German group or represent more recent case requiring court trial. Numerous dental restorations were noticed. Owing to the fact that different dental materials were used in dental practice at certain times, the aim of this study was to explore whether analysis of dental restorations could help in identification and estimation of time since death. Inductively coupled plasma optical emission spectrometry revealed that dental fillings corresponded to copper amalgam, conventional silver amalgam, silicophosphate cement, and zinc phosphate cement. Chemical results combined with anthropological and historical facts suggest that the individuals lived before the 1960s in country with well‐developed dental service at that time. Therefore, chemical analysis of dental fillings was useful to distinguish between skeletal remains that are too old to be of forensic interest and the remains relevant to legal investigations.

Novel calcium silicate based dental material with the addition of biologically active soy compound

Calcium silicate cements (CSC) present numerous properties that favor its use in dentistry. The purpose of this study was to investigate how the addition of soy extract affects porosity and wettability of the CSC. Soy was added to commercially available CSC named Portland cement (Italcementi, Spa Bergamo, Italy) at 10 weight % Pure Portland cement was used as a control material. Particle cement size was determined using scanning electron microscopy (TESCAN Mira3 XMU, USA Inc). Porosity of the cement was measured using micro computed tomography (μCT) (Skyscan 1172, Bruker, Belgium) at 10 μm isotropic resolution. Wettability of the cements was tested using contact angle analyzer and Endomethasone (Saint Maur, Cedex, France). Scanning electron microscopy has shown that Portland cement is composed of spherical and rods like particles ranging in size from 1 μm to 10 μm. The μCT analysis revealed that the addition of soy leads to an increased cements porosity. Both open and closed porosity values were higher in Portland cement with soy addition than in pure Portland cement. More than 70% of pores were in the range of 20-57 μm in both investigated groups. The addition of soy resulted in lower contact angles of Endomethasone on the cement surface, suggesting that this cement formulation possesses superior wettability. It can be deduced that soy is a promising candidate for Portland cement adhesive properties improvements.