Kunio Tsuda

Recessed-gate structure approach toward normally off high-Voltage AlGaN/GaN HEMT for power electronics applications

A recessed-gate structure has been studied with a view to realizing normally off operation of high-voltage AlGaN/GaN high-electron mobility transistors (HEMTs) for power electronics applications. The recessed-gate structure is very attractive for realizing normally off high-voltage AlGaN/GaN HEMTs because the gate threshold voltage can be controlled by the etching depth of the recess without significant increase in on-resistance characteristics. With this structure the threshold voltage can be increased with the reduction of two-dimensional electron gas (2DEG) density only under the gate electrode without reduction of 2DEG density in the other channel regions such as the channel between drain and gate. The threshold-voltage increase was experimentally demonstrated. The threshold voltage of fabricated recessed-gate device increased to -0.14 V while the threshold voltage without the recessed-gate structure was about -4 V. The specific on-resistance of the device was maintained as low as 4 m/spl Omega//spl middot/cm/sup 2/ and the breakdown voltage was 435 V. The on-resistance and the breakdown voltage tradeoff characteristics were the same as those of normally on devices. From the viewpoint of device design, the on-resistance for the normally off device was modeled using the relationship between the AlGaN layer thickness under the gate electrode and the 2DEG density. It is found that the MIS gate structure and the recess etching without the offset region between recess edge and gate electrode will further improve the on-resistance. The simulation results show the possibility of the on-resistance below 1 m/spl Omega//spl middot/cm/sup 2/ for normally off AlGaN/GaN HEMTs operating at several hundred volts with threshold voltage up to +1 V.

High breakdown voltage AlGaN-GaN power-HEMT design and high current density switching behavior

AlGaN-GaN power high-electron mobility transistors (HEMTs) with 600-V breakdown voltage are fabricated and demonstrated as switching power devices for motor drive and power supply applications. The fabricated power HEMT realized the high breakdown voltage by optimized field plate technique and the low on-state resistance of 3.3 m/spl Omega/cm/sup 2/, which is 20 times lower than that or silicon MOSFETs, thanks to the high critical field of GaN material and the high mobility in 2DEG channel. The fabricated devices also demonstrated the high current density switching of 850 A/cm/sup 2/ turn-off. These results show that AlGaN-GaN power-HEMTs are one of the most promising candidates for future switching power device for power electronics applications.

Suppression of Dynamic On-Resistance Increase and Gate Charge Measurements in High-Voltage GaN-HEMTs With Optimized Field-Plate Structure

The dynamic on-resistance increase associated with the current collapse phenomena in high-voltage GaN high-electron-mobility transistors (HEMTs) has been suppressed by employing an optimized field-plate (FP) structure. The fabricated GaN-HEMTs of 600 V/4.7 A and 940 V/4.4 A for power-electronics applications employ a dual-FP structure consisting of a short-gate FP underneath a long-source FP. The measured on-resistance shows minimal increase during high-voltage switching due to increased electric-field uniformity between the gate and drain as a result of using the dual FP. The gate-drain charge Q gd for the fabricated devices has also been measured to provide a basis for discussion of the ability of high-speed switching operation. Although Q gd /A (A: active device area) was almost the same as that of the conventional Si-power MOSFETs, R on A was dramatically reduced to about a seventh of the reported 600-V Si-MOSFET value. Therefore, R on Q gd for 600-V device was reduced to 0.32 OmeganC, which was approximately a sixth of that for the Si-power MOSFETs. The high-voltage GaN-HEMTs have significant advantages over silicon-power MOSFETs in terms of both the reduced on-resistance and the high-speed switching capability.

A 120-W Boost Converter Operation Using a High-Voltage GaN-HEMT

A boost converter with a 940-V/4.4 A GaN-HEMT as the main switching device was demonstrated to show the possibility of using high-voltage GaN-HEMTs in power electronic applications. The demonstrated circuit achieved an output power of 122 W and a power efficiency of 94.2% under a drain peak voltage as high as 350 V and a switching frequency of 1 MHz. The dual field-plate structure realized high-voltage switching operation with high power efficiency as dynamic on-resistance was suppressed by an increase of the current collapse phenomena.

Influence of surface defect charge at AlGaN-GaN-HEMT upon Schottky gate leakage current and breakdown voltage

The relation between Schottky gate leakage current and the breakdown voltage of AlGaN-GaN high-electron mobility transistors (HEMTs) is discussed based on the newly introduced simple, yet useful, surface defect charge model. This model represents the leakage current caused by the positive charge in the surface portion of AlGaN layer induced by process damage such as nitrogen vacancies. The new model has been implemented into a two-dimensional device simulator, and the relationship between the gate leakage current and the breakdown voltage was simulated. The simulation results reproduced the relationship obtained experimentally between the leakage current and the breakdown voltage. Further simulation and experiment results show that the breakdown voltage is maintained even if the defect charge exists up to the defect charge density of 2.5/spl times/10/sup 12/ cm/sup -2/, provided the field plate structure is adopted, while the breakdown voltage shows a sudden drop for the defect density over 5/spl times/10/sup 11/ cm/sup -2/ without the field plate. This result shows that the field plate structure is effective for suppressing the surface charge influence on breakdown voltage due to the relaxation of the electric field concentration in the surface portion of the AlGaN layer.

High breakdown Voltage undoped AlGaN-GaN power HEMT on sapphire substrate and its demonstration for DC-DC converter application

Undoped AlGaN-GaN power high electron mobility transistors (HEMTs) on sapphire substrate with 470-V breakdown voltage were fabricated and demonstrated as a main switching device for a high-voltage dc-dc converter. The fabricated power HEMT realized a high breakdown voltage with a field plate structure and a low on-state resistance of 3.9 m/spl Omega//spl middot/cm/sup 2/, which is 10 /spl times/ lower than that of conventional Si MOSFETs. The dc-dc converter operation of a down chopper circuit was demonstrated using the fabricated device at the input voltage of 300 V. These results show the promising possibilities of the AlGaN-GaN power HEMTs on sapphire substrate for future switching power devices.

Demonstration of 13.56-MHz class-E amplifier using a high-Voltage GaN power-HEMT

A 13.56-MHz class-E amplifier with a high-voltage GaN HEMT as the main switching device is demonstrated to show the possibility of using GaN HEMTs in high-frequency switching power applications such as RF power-supply applications. The 380-V/1.9-A GaN power HEMT was designed and fabricated for high-voltage power-electronics applications. The demonstrated circuit achieved the output power of 13.4 W and the power efficiency of 91% under a drain-peak voltage as high as 330 V. This result shows that high-voltage GaN devices are suitable for high-frequency switching applications under high dc input voltages of over 100 V.

Design optimization of high breakdown voltage AlGaN-GaN power HEMT on an insulating substrate for R/sub ON/A-V/sub B/ tradeoff characteristics

High breakdown voltage AlGaN-GaN power high-electron mobility transistors (HEMTs) on an insulating substrate were designed for the power electronics application. The field plate structure was employed for high breakdown voltage. The field plate length, the insulator thickness and AlGaN layer doping concentration were design parameters for the breakdown voltage. The optimization of the contact length and contact resistivity reduction were effective to reduce the specific on-resistance. The tradeoff characteristics between the on-resistance and the breakdown voltage can be improved by the optimization of the above design parameters, and the on-resistance can be estimated to be about 0.6 m/spl Omega//spl middot/cm/sup 2/ for the breakdown voltage of 600 V. This on-resistance is almost the same as that for the device on a conductive substrate.

600V AlGaN/GaN power-HEMT: design, fabrication and demonstration on high voltage DC-DC converter

A 600 V class AlGaN/GaN power HEMT was designed for high voltage power electronics application such as power supplies and motor drives. The fabricated device was demonstrated in a DC-DC down converter circuit, showing the future possibility of high efficiency and high frequency operations of AlGaN/GaN power HEMTs.

Transit-time reduction in AlGaAs/GaAs HBTs utilizing velocity overshoot in the p-type collector region

The effect of electron-velocity overshoot in a p-type GaAs collector on the transit-time reduction of AlGaAs/GaAs HBTs (heterojunction bipolar transistors) is investigated. A cutoff frequency improvement of about 30% over the conventional n-type GaAs collector was obtained in p-type collector HBTs for the same collector depletion-layer width. A significant increase in electron velocity in the p-type GaAs collector layer was confirmed by a simple analysis.<<ETX>>