Kyung Won Jung

Characteristics of biochar derived from marine macroalgae and fabrication of granular biochar by entrapment in calcium-alginate beads for phosphate removal from aqueous solution.

In this work, granular biochar, Laminaria japonica-derived biochar (LB)-calcium alginate beads (LB-CAB), was successfully prepared by dropping a mixture of powder biochar and alginate solution into a calcium chloride solution for phosphate adsorption. Among different marine macroalgae derived biochars, LB exhibited the best performance, showing a phosphate removal rate of 97.02%, which was attributed to its high Ca/P and Mg/P ratios. With increasing pyrolysis temperature up to 600°C, the physicochemical properties of LB became suitable for adsorbing phosphate. Experimental results of kinetics and equilibrium isotherms at different temperatures (10-30°C) showed that the phosphate adsorption process is endothermic and is mainly controlled by external mass transfer and the intraparticle diffusion rate. The maximum adsorption capacity was found to be 157.7mgg(-1) at 30°C, as fitted by the Langmuir-Freundlich model, which is higher than capacities of other powder form of biochars.

Synthesis of novel magnesium ferrite (MgFe2O4)/biochar magnetic composites and its adsorption behavior for phosphate in aqueous solutions

In this work, magnesium ferrite (MgFe2O4)/biochar magnetic composites (MFB-MCs) were prepared and utilized to remove phosphate from aqueous solutions. MFB-MCs were synthesized via co-precipitation of Fe and Mg ions onto a precursor, followed by pyrolysis. Characterization results confirmed that MgFe2O4 nanoparticles with a cubic spinel structure were successfully embedded in the biochar matrix, and this offered magnetic separability with superparamagnetic behavior and enabled higher phosphate adsorption performance than that of pristine biochar and sole MgFe2O4 nanoparticles. Batch experiments indicated that phosphate adsorption on the MFB-MCs is highly dependent on the pH, initial phosphate concentration, and temperature, while it was less affected by ionic strength. Analysis of activation and thermodynamic parameters as well as the isosteric heat of adsorption demonstrated that the phosphate adsorption is an endothermic and physisorption process. Lastly, highly efficient recyclability of the MFB-MCs suggested that they are a promising adsorbent for phosphate removal from wastewater.

Preparation of modified-biochar from Laminaria japonica: Simultaneous optimization of aluminum electrode-based electro-modification and pyrolysis processes and its application for phosphate removal

The preparation conditions of electro-modification (current density) and pyrolysis (pyrolysis temperature and heating rate) processes were simultaneously optimized using response surface methodology with the quadratic regression model associated with Box-Behnken design. By numerical optimization, the phosphate adsorption capacity of 245.06mg/g was achieved, corresponding to 99.9% of the predicted values under statistically optimized conditions (current density: 38.78mA/cm(2), pyrolysis temperature: 584.1°C, heating rate: 6.91°C/min). By considering R(2) and three error functions values, the experimental results of adsorption kinetics, and the equilibrium isotherms at different temperatures (10-30°C) showed that predictive pseudo-second-order and Sips isotherm models could adequately interpret the phosphate adsorption process for statistically optimized electrically modified-biochar (SOEM-biochar). The maximum phosphate adsorption capacities of SOEM-biochar were found to be 273.9, 345.1, and 460.3mg/g at 10, 20, and 30°C, respectively, which are higher than that of other adsorbents reported in the literature.

Adsorption of phosphate from aqueous solution using electrochemically modified biochar calcium-alginate beads: Batch and fixed-bed column performance

Batch and continuous fixed-bed column studies were investigated using electrochemically modified biochar calcium-alginate beads (EMB-CABs) as an adsorbent for the removal of phosphate from aqueous solutions. Batch experiments revealed that the phosphate adsorption behavior of EMB-CABs and its structural characteristics were highly dependent on pH condition. Also, kinetics and equilibrium isotherms studies demonstrated that the experimental data correlated well with the pseudo-second-order and Sips isotherm models, respectively. The effects of different operating parameters such as bed height, initial phosphate concentration, and flow rate were investigated in a continuous fixed-bed column, and the experimental data were fitted to three different breakthrough models, the Adams-Bohart, Thomas, and Yoon-Nelson models. The results suggested that the Yoon-Nelson model showed better agreement with the breakthrough curves than other models. Lastly, the design parameters for a large-scale column were calculated via the scale-up approach using the breakthrough parameters obtained from lab-scale column tests.

Facile one-pot hydrothermal synthesis of cubic spinel-type manganese ferrite/biochar composites for environmental remediation of heavy metals from aqueous solutions

This study reports the facile synthesis of cubic spinel-type manganese ferrite (MnFe2O4)/biochar (MF/BC) composites via a one-pot hydrothermal technique. Multiple characterizations demonstrated that the MnFe2O4 spinel nanoparticles were successfully grown on the biochar, which provides magnetic separability with superparamagnetic behavior and effective adsorption performance for heavy metals (Pb(II), Cu(II), and Cd(II)). The adsorption kinetics and isotherms can be well described with a pseudo-second-order and Sips isotherm models, respectively. Comparative adsorption in multi-heavy metal systems (binary and ternary) indicated that the adsorption affinity of MF/BC composites toward heavy metals followed the sequence of Pb(II)u202f>u202fCu(II)u202f>u202fCd(II), which followed the order of their covalent indexes. Thermodynamic analysis revealed that the adsorption process was endothermic and primarily governed by physisorption. This study provides a feasible and simple approach for the preparation of high-performance materials for the remediation of heavy metal-contaminated wastewater in a cost-effective manner.

Hydrothermal synthesis of hierarchically structured birnessite-type MnO 2 /biochar composites for the adsorptive removal of Cu(II) from aqueous media

In this study, hierarchical birnessite-type MnO2/biochar composites (δ-MnO2/BCs) were synthesized by a hydrothermal technique, and their Cu(II) removal performance was examined in aqueous solution. Morphological characterization confirmed that a three-dimensional flower-like structure of δ-MnO2 was formed, which results in effective adsorption affinity towards Cu(II). The effects of solution pH, adsorbent dosage, and ionic strength on the adsorption behavior of the prepared materials were systemically investigated. The adsorption kinetics indicated that Cu(II) adsorption onto δ-MnO2/BCs follows a pseudo-second-order model. Analysis of possible adsorption/diffusion mechanisms suggested that the adsorption process is controlled by both film and pore diffusion. The adsorption isotherms fit closely to the Sips isotherm model, and the theoretical maximum adsorption capacities of Cu(II) on the synthesized δ-MnO2/BCs are approximately 124, 154, 199, and 230u202fmg/g at 15, 25, 35, and 45u202f°C, respectively. Adsorption-desorption studies demonstrated the recyclability of the δ-MnO2/BCs for the removal of Cu(II) from aqueous solutions.