L. F. Fredette

NRC Welding Residual Stress Validation Program International Round Robin Program and Findings

The U.S. Nuclear Regulatory Commission (NRC) and the Electric Power Research Institute (EPRI) are working cooperatively under a memorandum of understanding to validate welding residual stress (WRS) predictions in pressurized water reactor (PWR) primary cooling loop components containing dissimilar metal (DM) welds. These stresses are of interest as DM welds in PWRs are susceptible to primary water stress corrosion cracking (PWSCC) and tensile weld residual stresses are the primary driver of this degradation mechanism. The NRC/EPRI weld residual stress (WRS) analysis validation program consists of four phases, with each phase increasing in complexity from laboratory size specimens to component mock-ups and cancelled-plant material. This paper discusses Phase 2 of the WRS characterization program involving an international round robin analysis project in which participants analyzed a prototypic reactor coolant pressure boundary component. Mock-up fabrication, WRS measurements and comparison with predicted stresses through the DM weld region are described. The results of this study show that, on average, analysts can develop WRS predictions that are a reasonable estimate for actual configurations as quantified by measurements. However, the scatter in predicted results from analyst to analyst can be quite large. For example, in this study, the scatter in WRSs through the centerline of the main DM weld (prior to stainless steel weld application) predicted by analysts is approximately +/− 200 to 300 MPa at 3 standard deviations for axial stresses and +/− 300 to 400 MPa at 3 standard deviations for hoop stresses. Sensitivity studies that vary important parameters, such as material hardening behavior, can be used to bound such large variations.Copyright

An Analytical Evaluation of the Full Structural Weld Overlay as a Stress Improving Mitigation Strategy to Prevent Primary Water Stress Corrosion Cracking in Pressurized Water Reactor Piping

Full Structural Weld Overlay (FSWOL) has been used successfully to mitigate intergranular stress corrosion cracking in boiling water reactor (BWR) welded stainless steel piping for many years. The FSWOL technique adds structural reinforcement, can add crack resistant material, and can create compressive residual stresses at the inside surface of the welded joint which reduces the possibility of further stress corrosion cracking. Recently, the FSWOL has been applied as a preemptive measure to prevent primary water stress corrosion cracking (PWSCC) in pressurized water reactors (PWR) on susceptible welded pipes with dissimilar metal welds common to PWR primary cooling piping. This study uses finite element models to evaluate the likely residual and operating stress profiles remaining after FSWOL for typical dissimilar metal weld configurations, some of which are approved for leak-before-break (LBB) applications in pressurized water reactors. Circumferential cracks were modeled in the dissimilar metal weld area and forced to grow in order to evaluate their crack opening displacements and stress intensity factors vs. depth before and after weld overlay and before and after application of operating pressure and temperature.

Effect of Weld Induced Residual Stresses on Pipe Crack Opening Areas and Implications on Leak-Before-Break Considerations

The USNRC is anticipating updating their leak-before-break (LBB) procedures. One of the technical areas of concern in the existing procedures is the prediction of the crack-opening-displacements (COD) needed for estimating the postulated leakage crack size for a prescribed leakage detection capability. If cracks develop in the welded area of a pipe, as is often the case, residual stresses in the weld may cause the crack to be forced closed. Earlier studies have shown that pipe welding produces high residual stresses with a sharp stress gradient ranging from tension to compression through the thickness of the welded area of the pipe. The current guidelines are inadequate to predict crack size based on leak rates for cracks in welded areas of pipes. The current guidelines rely on the calculation of the crack-opening-displacement as related to pipe loading. Values from the current guidelines are used to predict a crack’s cross sectional area and, in turn, to determine the severity of an existing crack by monitoring in-service leakage rates. The equations currently in use are applicable to service loaded pipe material only. Residual stresses caused by cold work, welding, etc. are neglected. This study uses two and three dimensional finite element models and weld residual stress calculation software created at Battelle Memorial Institute to develop correction factors to be used with the traditional design equations. The correction factors will compensate for the effects of welding induced residual stresses on cracks in pipe welds. This study concentrates on type 316 stainless steel material properties, but the COD corrections should be equally applicable to all stainless steels, and also can be used for ferritic steels. A test matrix of pipe radius, thickness, and crack size was used to develop the equation correction factors. Pipe wall thicknesses (t) of 7.5 mm (0.295 in.), 15 mm (0.590 in.), 22.5 mm (0.886 in.), and 30 mm (1.181 in.) were studied in pipes with mean radius to thickness ratios of 5, 10, and 20. Cracks with half-lengths in radians of π/16, π/8, π/4, and π/2 were introduced in these virtual pipes. The matrix of results was used to produce correction factors for crack opening displacement equations applicable to a broad range of pipe sizes.Copyright

NRC/EPRI Welding Residual Stress Validation Program - Phase III

The US Nuclear Regulatory Commission (NRC) and the Electric Power Research Institute (EPRI) are working cooperatively under a memorandum of understanding to validate welding residual stress predictions in pressurized water reactor primary cooling loop components containing dissimilar metal (DM) welds. These stresses are of interest as DM welds in pressurized water reactors are susceptible to primary water stress corrosion cracking (PWSCC) and tensile weld residual stresses are one of the primary drivers of this stress corrosion cracking mechanism. The NRC/EPRI welding residual stress (WRS) program currently consists of four phases, with each phase increasing in complexity from lab size specimens to component mock-ups and ex-plant material.

An Analytical Evaluation of the Effect of Weld Sequencing on Residual Stresses Produced by Full Structural Weld Overlays on Pressurized Water Reactor Primary Cooling Piping

Full Structural Weld Overlay (FSWOL) has been used successfully to mitigate intergranular stress corrosion cracking in boiling water reactor (BWR) welded stainless steel piping for many years. The FSWOL technique adds structural reinforcement, can add crack resistant material, and can create compressive residual stresses at the inside surface of the welded joint which reduces the possibility of further stress corrosion cracking. Recently, the FSWOL has been applied as a preemptive measure to prevent primary water stress corrosion cracking (PWSCC) in pressurized water reactors (PWR) on susceptible welded pipes with dissimilar metal welds common to PWR primary cooling piping. This study uses finite element models to evaluate the likely residual and operating stress profiles remaining after FSWOL for typical dissimilar metal weld configurations and describes the results of sensitivity studies which were performed to examine the effect of weld sequencing on the residual stresses produced in common configurations of PWR primary cooling system piping.

An Analytical Evaluation of the Effect of Weld Material Thickness on Residual Stresses Produced by Structural Weld Overlays on Pressurized Water Reactor Primary Cooling Piping

Full Structural Weld Overlay (FSWOL) has been used successfully to mitigate intergranular stress corrosion cracking in boiling water reactor (BWR) welded stainless steel piping for many years. The FSWOL technique adds structural reinforcement, can add crack resistant material, and can create compressive residual stresses at the inside surface of the welded joint which reduces the possibility of further stress corrosion cracking. Recently, the FSWOL has been applied as a preemptive measure to prevent primary water stress corrosion cracking (PWSCC) in pressurized water reactors (PWR) on susceptible welded pipes with dissimilar metal welds common to PWR primary cooling piping. This study uses finite element models to evaluate the likely residual and operating stress profiles remaining after FSWOL and describes the results of sensitivity studies which were performed to examine the effect of weld overlay thickness on the residual stresses for typical dissimilar metal weld configurations.