L.G. Franquelo

Power-Electronic Systems for the Grid Integration of Renewable Energy Sources: A Survey

The use of distributed energy resources is increasingly being pursued as a supplement and an alternative to large conventional central power stations. The specification of a power-electronic interface is subject to requirements related not only to the renewable energy source itself but also to its effects on the power-system operation, especially where the intermittent energy source constitutes a significant part of the total system capacity. In this paper, new trends in power electronics for the integration of wind and photovoltaic (PV) power generators are presented. A review of the appropriate storage-system technology used for the integration of intermittent renewable energy sources is also introduced. Discussions about common and future trends in renewable energy systems based on reliability and maturity of each technology are presented

Recent Advances and Industrial Applications of Multilevel Converters

Multilevel converters have been under research and development for more than three decades and have found successful industrial application. However, this is still a technology under development, and many new contributions and new commercial topologies have been reported in the last few years. The aim of this paper is to group and review these recent contributions, in order to establish the current state of the art and trends of the technology, to provide readers with a comprehensive and insightful review of where multilevel converter technology stands and is heading. This paper first presents a brief overview of well-established multilevel converters strongly oriented to their current state in industrial applications to then center the discussion on the new converters that have made their way into the industry. In addition, new promising topologies are discussed. Recent advances made in modulation and control of multilevel converters are also addressed. A great part of this paper is devoted to show nontraditional applications powered by multilevel converters and how multilevel converters are becoming an enabling technology in many industrial sectors. Finally, some future trends and challenges in the further development of this technology are discussed to motivate future contributions that address open problems and explore new possibilities.

The age of multilevel converters arrives

This work is devoted to review and analyze the most relevant characteristics of multilevel converters, to motivate possible solutions, and to show that we are in a decisive instant in which energy companies have to bet on these converters as a good solution compared with classic two-level converters. This article presents a brief overview of the actual applications of multilevel converters and provides an introduction of the modeling techniques and the most common modulation strategies. It also addresses the operational and technological issues.

Multilevel Converters: An Enabling Technology for High-Power Applications

Multilevel converters are considered today as the state-of-the-art power-conversion systems for high-power and power-quality demanding applications. This paper presents a tutorial on this technology, covering the operating principle and the different power circuit topologies, modulation methods, technical issues and industry applications. Special attention is given to established technology already found in industry with more in-depth and self-contained information, while recent advances and state-of-the-art contributions are addressed with useful references. This paper serves as an introduction to the subject for the not-familiarized reader, as well as an update or reference for academics and practicing engineers working in the field of industrial and power electronics.

Energy Storage Systems for Transport and Grid Applications

Energy storage systems (ESSs) are enabling technologies for well-established and new applications such as power peak shaving, electric vehicles, integration of renewable energies, etc. This paper presents a review of ESSs for transport and grid applications, covering several aspects as the storage technology, the main applications, and the power converters used to operate some of the energy storage technologies. Special attention is given to the different applications, providing a deep description of the system and addressing the most suitable storage technology. The main objective of this paper is to introduce the subject and to give an updated reference to nonspecialist, academic, and engineers in the field of power electronics.

Model Predictive Control of an Inverter With Output

The use of an inverter with an output LC filter allows for generation of output sinusoidal voltages with low harmonic distortion, suitable for uninterruptible power supply systems. However, the controller design becomes more difficult. This paper presents a new and simple control scheme using predictive control for a two-level converter. The controller uses the model of the system to predict, on each sampling interval, the behavior of the output voltage for each possible switching state. Then, a cost function is used as a criterion for selecting the switching state that will be applied during the next sampling interval. In addition, an observer is used for load-current estimation, enhancing the behavior of the proposed controller without increasing the number of current sensors. Experimental results under linear and nonlinear load conditions, with a 5.5-kW prototype, are presented, verifying the feasibility and good performance of the proposed control scheme.

LC

Photovoltaic (PV) energy has grown at an average annual rate of 60% in the last five years, surpassing one third of the cumulative wind energy installed capacity, and is quickly becoming an important part of the energy mix in some regions and power systems. This has been driven by a reduction in the cost of PV modules. This growth has also triggered the evolution of classic PV power converters from conventional single-phase grid-tied inverters to more complex topologies to increase efficiency, power extraction from the modules, and reliability without impacting the cost. This article presents an overview of the existing PV energy conversion systems, addressing the system configuration of different PV plants and the PV converter topologies that have found practical applications for grid-connected systems. In addition, the recent research and emerging PV converter technology are discussed, highlighting their possible advantages compared with the present technology.

Filter for UPS Applications

Model Predictive Control with a finite control set has emerged as a promising control tool for power converters and drives. One of the major advantages is the possibility to control several system variables with a single control law, by including them with appropriate weighting factors. However, at the present state of the art, these coefficients are determined empirically. There is no analytical or numerical method proposed yet to obtain an optimal solution. In addition, the empirical method is not always straightforward, and no procedures have been reported. This paper presents a first approach to a set of guidelines that reduce the uncertainty of this process. First a classification of different types of cost functions and weighting factors is presented. Then the different steps of the empirical process are explained. Finally, results for several power converters and drives applications are analyzed, which show the effectiveness of the proposed guidelines to reach appropriate weighting factors and control performance.

Grid-Connected Photovoltaic Systems: An Overview of Recent Research and Emerging PV Converter Technology

The main design objective of photovoltaic (PV) systems has been, for a long time, to extract the maximum power from the PV array and inject it into the ac grid. Therefore, the maximum power point tracking (MPPT) of a uniformly irradiated PV array and the maximization of the conversion efficiency have been the main design issues. However, when the PV plant is connected to the grid, special attention has to be paid to the reliability of the system, the power quality, and the implementation of protection and grid synchronization functions. Modern power plants are required to maximize their energy production, requiring suitable control strategies to solve the problems related to the partial shading phenomena and different orientation of the PV modules toward the sun. Moreover, the new policy concerning the injection of reactive power into the grid makes the development of suitable topologies and control algorithms mandatory. A general view of actual solutions for applications of the PV energy systems is presented. This article covers several important issues, including the most reliable models used for simulation, which are useful in the design of control systems, and the MPPT function, particularly in distributed applications. The main topologies used in the PV power processing system and, finally, grid connection aspects are discussed, with emphasis on synchronization, protections, and integration.

Guidelines for weighting factors design in Model Predictive Control of power converters and drives

Model-based predictive control (MPC) for power converters and drives is a control technique that has gained attention in the research community. The main reason for this is that although MPC presents high computational burden, it can easily handle multivariable case and system constraints and nonlinearities in a very intuitive way. Taking advantage of that, MPC has been successfully used for different applications such as an active front end (AFE), power converters connected to resistor inductor RL loads, uninterruptible power supplies, and high-performance drives for induction machines, among others. This article provides a review of the application of MPC in the power electronics area.