Laetitia Picart-Palmade

Foaming and adsorption behavior of bovine and camel proteins mixed layers at the air/water interface

The aim of this work was to examine foaming and interfacial behavior of three milk protein mixtures, bovine α-lactalbumin-β-casein (M1), camel α-lactalbumin-β-casein (M2) and β-lactoglobulin-β-casein (M3), alone and in binary mixtures, at the air/water interface in order to better understand the foaming properties of bovine and camel milks. Different mixture ratios (100:0; 75:25; 50:50; 25:75; 0:100) were used during foaming tests and interfacial protein interactions were studied with a pendant drop tensiometer. Experimental results evidenced that the greatest foam was obtained with a higher β-casein amount in all camel and bovine mixtures. Good correlation was observed with the adsorption and the interfacial rheological properties of camel and bovine protein mixtures. The proteins adsorbed layers are mainly affected by the presence of β-casein molecules, which are probably the most abundant protein at interface and the most efficient in reducing the interfacial properties. In contrast of, the globular proteins, α-lactalbumin and β-lactoglobulin that are involved in the protein layer composition, but could not compact well at the interface to ensure foams creation and stabilization because of their rigid molecular structure.

The foaming properties of camel and bovine whey: The impact of pH and heat treatment

The effect of heat treatment (70°C or 90°C for 30min) on the foaming and interfacial properties of acid and sweet whey obtained from bovine and camel fresh milk was examined. The maximum foamability and foam stability were observed for acid whey when compared to sweet whey for both milks, with higher values for the camel whey. This behavior for acid whey was explained by the proximity of the pI of whey protein (4.9-5.2), where proteins were found to carry the lowest negative charge as confirmed by the zeta potential measurements. Interfacial properties of acid camel whey and acid bovine whey were preserved at air water interface even after a heat treatment at 90°C. These results confirmed the pronounced foaming and interfacial properties of acid camel whey, even if acid and sweet bovine whey exhibited the highest viscoelastic modulus after heating.

Submicron emulsions processed by ultra-high pressure homogenization

Model oil/water (O/W) emulsions containing (w/w) 15–45% peanut oil plus 4.3% whey proteins or raw whole milk (∼4%, w/w, fat) were processed by ultra-high pressure (HP) homogenization at an inlet temperature of 24 °C using an HP homogenizer with an HP valve, immediately followed by cooling heat exchangers. Mechanical and thermal energies involved in the process were calculated using pressure and temperature values measured at the HP valve inlet and immediate outlet. For all samples, an increase in homogenization pressure decreased the droplet size, leading to submicron fat particles at pressure≥200 MPa and monomodal distributions in the nano-scale range by emulsion recycling once or twice at 200 MPa. Further, microbial inactivation in raw whole milk was enhanced by increasing the homogenization pressure or by recycling milk at 200 MPa. Rheological behavior of model O/W emulsions varied as a function of oil droplet size and oil volume fraction.

The effect of pH and heat treatments on the foaming properties of purified α-lactalbumin from camel milk

The effect of pH (4.3 or 6.5) and heat treatment (70°C or 90°C for 30min) on the foaming and interfacial properties of α-lactalbumin extracted from camel milk were studied. The increased temperature treatment changed the foaming properties of camel α-lactalbumin solution and its ability to unfold at the air-water interface. At neutral pH, heat treatment was found to improve foamability, whereas at acid pH (4.3) this property decreased. Foams were more stable after a heat treatment at pH 4.3 than at 6.5, due to higher levels of protein aggregation at low pH. Heat treatment at 90°C for 30min affected the physicochemical properties of the camel α-lactalbumin by increasing free thiol group concentration at pH 6.5. Heat treatment also caused changes in α-lactalbumins surface charge. These results also confirm the pronounced aggregation of heated camel α-lactalbumin solution at acid pH.

UHPH-processed O/W submicron emulsions stabilised with a lipid-based surfactant: physicochemical characteristics and behaviour on in vitro TC7-cell monolayers and ex vivo pig's ear skin.

Submicron O/W emulsions formulated with sesame oil plus a lipid-base surfactant, and with or without retinyl acetate (RAC) as a model hydrophobic biomolecule, were prepared by single-pass homogenisation at ≥ 200 MPa (UHPH) and an initial fluid temperature (Tin) of 24°C. These emulsions were characterised by a monomodal distribution (peak maximum at 260 nm) and a 2-year potential physical stability at ambient temperature. Submicron droplets were investigated in term of (i) physicochemical characteristics (size distribution curves; ζ-potential value), and (ii) impact on TC7-cell monolayers (MTT-assay and cell LDH-leakage). Submicron droplets ± RAC did not affect or increased significantly (p=0.05) TC7-cell metabolic activity after 4-24h of exposure indicating absence of cellular impairment, except when high amounts of droplets were deposed on TC7-cells. Indeed, the lipid-based surfactant deposed alone on TC7-cells at high concentration, induced some significant (p=0.05) cell LDH-leakage, and therefore cell-membrane damage. Cellular uptake experiments revealed a significant (p=0.05) time-dependent internalisation of RAC from submicron droplets, and cellular transformation of RAC into retinol. The turnover of RAC into retinol and therefore RAC bioaccessibility appeared faster for RAC-micelles of similar size-range and prepared at atmospheric pressure with polysorbate 80, than for submicron O/W emulsions. Permeation experiments using pigs ear skin mounted on Franz-type diffusion cells, revealed RAC in dermis-epidermis, in significantly (p=0.05) higher amounts for submicron than coarse pre-emulsions. However, RAC amounts remained low for both emulsion-types and RAC was not detected in the receptor medium of Franz-type diffusion cells.

Performances of different protocols for exocellular polysaccharides extraction from milk acid gels: Application to yogurt

Dextran or xanthan were used as model exocellular polysaccharides (EPS) to compare the extraction efficiency of EPS from skim milk acid gels using three different protocols. Extraction yields, residual protein concentrations and the macromolecular properties of extracted EPS were determined. For both model EPS, the highest extraction yield (∼80%) was obtained when samples were heated in acidic conditions at the first step of extraction (Protocol 1). Protocols that contained steps of acid/ethanol precipitation without heating (Protocols 2 and 3) show lower extraction yields (∼55%) but allow a better preservation of the EPS macromolecular properties. Changing the pH of acid gels up to 7 before extraction (Protocol 3) improved the extraction yield of anionic EPS without effect on the macromolecular properties of EPS. Protocol 1 was then applied for the quantification of EPS produced during the yogurt fermentation, while Protocol 3 was dedicated to their macromolecular characterization.