Laurence Donato

Internal structure and colloidal behaviour of covalent whey protein microgels obtained by heat treatment

Covalently cross-linked whey protein microgels (WPM) were produced without the use of a chemical cross-linking agent. The hierarchical structure of WPM is formed by a complex interplay of heat denaturation, aggregation, electrostatic repulsion, and formation of disulfide bonds. Therefore, well-defined spherical particles with a diameter of several hundreds of nanometers and with relatively low polydispersity are formed in a narrow pH regime (5.8–6.2) only. WPM production was carried out on large scale by heating a protein solution in a plate-plate heat exchanger. Thereafter, the microgels were concentrated by microfiltration and spray dried into a powder. The spherical structure of the WPM was conserved in the powder. After re-dispersion, the microgel dispersions fully recovered their initial structure and size distribution. Due to the formation of disulfide bonds the particles were internally covalently cross-linked and were remarkably stable in a large pH range. Because of the pH dependent charge of the constituents the particles underwent significant size changes upon shifting the pH. Small angle X-ray scattering experiments were used to reveal their internal structure, and we report on the pH-induced structural changes occurring on different length scale. Our experiments showed that close analogies could be drawn to internally cross-linked and pH-responsive microgels based on weak polyelectrolytes. WPM also exhibited a pronounced swelling at pH values below the isoelectric point (IEP), and a collapse at the IEP. However, in contrast to classical microgels, WPM are not build up by simple polymer chains but possess a complex hierarchical structure consisting of strands formed by clusters of aggregated denatured proteins that act as primary building blocks. They were flexible enough to respond to changes of the environment, and were stable enough to tolerate pH values where the proteins were highly charged and the strands were stretched.

On the Crucial Importance of the pH for the Formation and Self-Stabilization of Protein Microgels and Strands

Stable suspensions of protein microgels are formed by heating salt-free β-lactoglobulin solutions at concentrations up to about C = 50 g·L(-1) if the pH is set within a narrow range between 5.75 and 6.1. The internal protein concentration of these spherical particles is about 150 g·L(-1) and the average hydrodynamic radius decreases with increasing pH from 200 to 75 nm. The formation of the microgels leads to an increase of the pH, which is a necessary condition to obtain stable suspensions. The spontaneous increase of the pH during microgel formation leads to an increase of their surface charge density and inhibits secondary aggregation. This self-stabilization mechanism is not sufficient if the initial pH is below 5.75 in which case secondary aggregation leads to precipitation. Microgels are no longer formed above a critical initial pH, but instead short, curved protein strands are obtained with a hydrodynamic radius of about 15-20 nm.

Tuning the structure of protein particles and gels with calcium or sodium ions.

The effect of the addition of NaCl or CaCl2 on the structure of protein particles and gels was investigated in detail for aqueous solutions of the globular milk protein β-lactoglobulin at 40g/L and pH 7.0. When heated in the presence of NaCl or at very low CaCl2 concentrations, the proteins form small strand-like particles, but if more than about two Ca(2+) ions per protein are present, larger spherical particles (microgels) are formed, which increase in size with increasing CaCl2 concentration. The effect of the heating temperature was investigated between 62 and 85 °C. At lower heating temperatures, more Ca(2+) ions per protein are needed to drive the formation of microgels. Particle size measurements done with dynamic light scattering suggest that the aggregation occurs via a nucleation and growth process. The nuclei grow either by fusion or by addition of denatured proteins. If more than three Ca(2+) ions per protein are added, particulate gels are formed by random association of the microgels. Similar particulate gels are also formed at high NaCl concentrations (>200 mM), but by a different mechanism. In this case, the randomly aggregated small strands formed at the early stage of the heating process formed dense spherical domains at a later stage of the heating process by microphase separation that randomly associated to form a particulate gel.

Heteroprotein Complex Coacervation: Bovine β‑Lactoglobulin and Lactoferrin

Lactoferrin (LF) and β-lactoglobulin (BLG), strongly basic and weakly acidic bovine milk proteins, form optically clear coacervates under highly limited conditions of pH, ionic strength I, total protein concentration C(P), and BLG:LF stoichiometry. At 1:1 weight ratio, the coacervate composition has the same stoichiometry as its supernatant, which along with DLS measurements is consistent with an average structure LF(BLG2)2. In contrast to coacervation involving polyelectrolytes here, coacervates only form at I < 20 mM. The range of pH at which coacervation occurs is similarly narrow, ca. 5.7-6.2. On the other hand, suppression of coacervation is observed at high C(P), similar to the behavior of some polyelectrolyte-colloid systems. It is proposed that the structural homogeneity of complexes versus coacervates with polyelectrolytes greatly reduces the entropy of coacervation (both chain configuration and counterion loss) so that a very precise balance of repulsive and attractive forces is required for phase separation of the coacervate equilibrium state. The liquid-liquid phase transition can however be obscured by the kinetics of BLG aggregation which can compete with coacervation by depletion of BLG.