Linda Zou

Photosynthesis of hydrogen and methane as key components for clean energy system

Abstract While researchers are trying to solve the world’s energy woes, hydrogen is becoming the key component in sustainable energy systems. Hydrogen could be produced through photocatalytic water-splitting technology. It has also been found that hydrogen and methane could be produced through photocatalytic reduction of carbon dioxide with water. In this exploratory study, instead of coating catalysts on a substrate, pellet form of catalyst, which has better adsorption capacity, was used in the photo-reduction of carbon dioxide with water. In the experiment, some water was first absorbed into titanium dioxide pellets. Highly purified carbon dioxide gas was then discharged into a reactor containing these wet pellets, which were then illuminated continuously using UVC lamps. Gaseous samples accumulated in the reactor were extracted at different intervals to analyze the product yields. The results confirmed that methane and hydrogen were photosynthesized using pellet form of TiO2 catalysts. Hydrogen was formed at a rate as high as 0.16 micromoles per hourμmol h–1). The maximum formation rate of CH4 was achieved at 0.25 μmol h–1 after 24 h of irradiation. CO was also detected.

Photocatalytic Production of Methane and Hydrogen Through Reduction of Carbon Dioxide with Water Using Titania Pellets

This paper presents an experimental study on employing a pellet form of catalyst in photo-reduction of carbon dioxide with water. Water was first absorbed into titania pellets. Highly purified carbon dioxide gas was then discharged into a reactor containing the wet pellets, which were then illuminated continuously for 65 hours using UVC lamps. Analysing the products accumulated in the reactor confirmed that methane and hydrogen were produced through photo-reduction of carbon dioxide with water. No other hydrocarbons were detected. Increasing the temperature in the reactor has showed little change on the amount of methane produced.

Enhanced degradation efficiency of toluene using titania/silica photocatalysis as a regeneration process

Three kinds of titania/silica pellets were prepared using the sol-gel method with surface areas of 50.4m2 g−1, 421.1m2.g−1 and 89.1m2.g−1. An annular reactor was designed and built to determine the degradation efficiency of toluene and to investigate the relationship between the adsorption and desorption-photocatalytic processes. Surface area is an important factor influencing the adsorption-photocatalytic efficiency. Higher surface areas of pellets contribute to high rates of conversion of toluene. Un-reacted toluene and reaction intermediates accumulating on their surface deactivated the titania/silica catalyst. To overcome this problem, the adsorption and regeneration process were alternated in a dual reactor system. Connecting or disconnecting the toluene feed gas enabled one reactor to adsorb toluene, while the second reactor was regenerated by photocatalysis. Using UV irradiation and titania/silica pellets with high BET surface area (421.1 m2.g−1), the alternating adsorption/regeneration processes kept the degradation efficiency of toluene at 90% after 8 hours operation. By improving the adsorption-photocatalysis efficiency, and minimising the generation and accumulation of intermediate on the surface of pellets, the method extended catalyst life and maintained a high degradation efficiency of toluene.

A comparative study on preparation of TiO2 pellets as photocatalysts based on different precursors

The porous TiO2 pellets were prepared based on pigment grade titaina, P25 titania powder and titanium(IV) butoxide. The characterization was done with X-Ray diffraction, scanning electron microscopy and BET measurements. The result shows that TiO2 pellets by using titanium(IV) butoxide with some addictive have the best surface porosity, with specific surface area of 196.9m2/g. For pigment grade titania and P25 titania powder, it is still effective to enhance the surface area after reassembling. The surface area increased from 11.6 to 29.2 m2/g for pigment grade titania and from 50 to 84.4 m2/g for P25 titania powder. Furthermore, it has been investigated on how to optimize and get the highest surface area by controlling the sintering temperature, reaction temperature, pH of solution, and the amount of alcohol and addictive of surfactant during preparation. The experimental photocatalytic degradation of acetone and toluene was performed using titania pellets made from P25 titania powder.