Linn Berglund

Membranes Based on Cellulose Nanofibers and Activated Carbon for Removal of Escherichia coli Bacteria from Water

Cellulosic nanomaterials are potential candidates in different areas, especially in water treatment. In the current work, palm fruit stalks cellulose nanofibers (CNF), TEMPO-oxidized CNF (OCNF), and activated carbon (AC) were used to make thin film membranes for removal of E. coli bacteria from water. Two types of layered membranes were produced: a single layer setup of crosslinked CNF and a two-layer setup of AC/OCNF (bottom) and crosslinked CNF (up) on hardened filter paper. The prepared membranes were evaluated regarding their microstructure and layers thickness using scanning electron microscopy (SEM). Water flux and rejection of E. coli bacteria was tested using dead end stirred cells at 1 MPa pressure. Thickness of the cosslinked CNF layer in both types of membranes was about 0.75 micron. The results showed that exchanging water by isopropyl alcohol before drying increased porosity of membranes, and thus resulted in increasing pure water flux and flux of bacteria suspension. The two-layer AC/OCNF/CNF membrane had much higher water flux than the single layer CNF due to higher porosity seen on the surface of the former. Both types of membranes showed high capability of removing E. coli bacteria (rejection ~96–99%) with slightly higher efficiency for the AC/OCNF/CNF membrane than CNF membrane. AC/OCNF/CNF membrane also showed resistance against growth of E. coli and S. aureus bacteria on the upper CNF surface while the single layer CNF membrane did not show resistance against growth of the aforementioned bacteria.

Use of Bacterial Cellulose and Crosslinked Cellulose Nanofibers Membranes for Removal of Oil from Oil-in-Water Emulsions

Never-dried bacterial cellulose (BC) and crosslinked cellulose nanofibers (CNF) were used for the removal of oil from stabilized and non-stabilized oil-in-water emulsions with droplet sizes less than 1 µm. The CNF membranes were exchanged with isopropyl alcohol before drying. The microscopic structure of the prepared membranes was evaluated using scanning electron microscopy (SEM); the water flux and the rejection of oil were evaluated using a dead-end filtration cell. BC harvested after different incubation time periods (2 to 10 days) did not show a change in the width of the nanofibers, but only the thickness of the membranes was increased. Pure water flux was not affected as a result of increasing thicknesses of BC membranes harvested after 4–10 days while BC harvested after two days had significantly higher water flux than the others. BC showed a higher flux and efficiency in removing oil from oil emulsions than CNF membranes. Removal of oil by the different membranes from the non-stabilized oil emulsion was more efficient than from the stabilized one.

Gliding arc surface modification of carrot nanofibre coating - perspective for composite processing

Surfaces of carrot nanofibre coatings were modified by a gliding arc in atmospheric pressure air. The treatment strengthened wetting of deionized water and glycerol, increased an oxygen content, C-O and C=O, and moderately roughened the surfaces. In the perspective of composite materials, these changes to the nanofibres can potentially improve their processability when they are to be impregnated with a polymeric matrix. However, longer exposure to the gliding arc reduced oxidation and roughness of the surface, and thus there exists an optimum condition to achieve good wetting to solvents.

Dielectric barrier discharge plasma treatment of cellulose nanofibre surfaces

ABSTRACT Dielectric barrier discharge plasma treatment was applied to modify cellulose nanofibre (CNF) surfaces with and without ultrasonic irradiation. The plasma treatment improved the wetting by deionised water and glycerol, and increased the contents of oxygen, carbonyl group, and carboxyl group on the nanofibre surface. Ultrasonic irradiation further enhanced the wetting and oxidation of the nanofibre coating. Scanning electron microscopic observations showed skeleton-like features on the plasma-treated surface, indicating preferential etching of weaker domains, such as low-molecular weight domains and amorphous phases. Ultrasonic irradiation also improved the uniformity of the treatment. Altogether, it is demonstrated that atmospheric pressure plasma treatment is a promising technique to modify the CNF surface before composite processing.

Effect of xylanase pretreatment of rice straw unbleached soda and neutral sulfite pulps on isolation of nanofibers and their properties

There is a recent interest in producing cellulose nanofibers with different surface properties from unbleached cellulose pulps for economic and environmental reasons. In the current study we investigated the use of xylanase pretreatment on two types of unbleached rice straw pulps, namely, soda and neutral sulfite, and their fibrillation to nanofibers using ultrafine grinding. The effect of xylanase pretreatment on the fibrillation progress, energy consumption, and nanofiber dimensions was studied. In addition, mechanical properties, water contact angle, water absorption, and roughness of produced nanopapers were studied. Although very thin nanofibers with a homogenous width could be isolated from both xylanase-treated and untreated pulps, the xylanase pretreatment resulted in faster fibrillation. In addition, nanopapers prepared from xylanase-treated nanofibers had better mechanical properties than those isolated from the untreated pulps. The energy consumption during fibrillation depended on the type of pulp; a slightly lower energy consumption (~ 8%) was recorded for xylanase-treated soda pulp while a higher energy consumption (~ 21%) was recorded for xylanase-treated neutral sulfite pulp compared to the untreated pulps.Graphical Abstract

Potential of municipal solid waste paper as raw material for production of cellulose nanofibres

When aiming for higher resource efficiency, greater utilization of waste streams is needed. In this work, waste paper separated from mixed municipal solid waste (MSW) was studied as a potential starting material for the production of cellulose nanofibres (CNFs). The waste paper was treated using three different techniques, namely pulping, flotation and washing, after which it was subjected to an ultrafine grinding process to produce CNFs. The energy consumption of the nanofibrillation and nanofibre morphology, as well as properties of the prepared nanofibers, were analysed. Despite the varying amounts of impurities in the waste fibres, all samples could be fibrillated into nanoscale fibres. The tensile strengths of the CNF networks ranged from 70 to 100 MPa, while the stiffness was ∼7 GPa; thus, their mechanical strength can be adequate for applications in which high purity is not required. The contact angles of the CNF networks varied depending on the used treatment method: the flotation-treated networks were more hydrophilic (contact angle 52.5°) and the washed networks were more hydrophobic (contact angle 72.6°).