Lippo Lassila
University of Turku
Network
Latest external collaboration on country level. Dive into details by clicking on the dots.
Publication
Featured researches published by Lippo Lassila.
Acta Odontologica Scandinavica | 2005
Lippo Lassila; Arzu Tezvergil; Milla S. Lahdenperä; Pasi Alander; Akiyoshi Shinya; Akikazu Shinya; Pekka K. Vallittu
Objective. Water sorption, flexural properties, bonding properties, and elemental composition of photopolymerizable resin-impregnated fiber-reinforced composite (FRC) materials (everStick C&B and BR-100) (FPD) were evaluated in this study. Material and methods. Bar-shaped specimens (2×2×25 mm) were prepared for water sorption and flexural strength testing. The specimens (n=6) were polymerized either with a hand light-curing unit for 40 s or, additionally, in a light-curing oven for 20 min and stored in water for 30 days. Water sorption was measured during this time, followed by measurements of flexural strength and modulus. A shear bond strength test was performed to determine the bonding characteristics of polymerized FRC to composite resin luting cement (Panavia-F), (n=15). The cement was bonded to the FRC substrate and the specimens were thermocycled 5000 times (5–55°C) in water. SEM/EDS were analyzed to evaluate the elemental composition of the glass fibers and the fiber distribution in cross section. Results. ANOVA showed significant differences in water sorption according to brand (p<0.05). Water sorption of everStick C&B was 1.86 wt% (hand-unit polymerized) and 1.94 wt% (oven polymerized), whereas BR-100 was 1.07 wt% and 1.17 wt%, respectively. The flexural strength of everStick C&B after 30 days’ water storage was 559 MPa (hand-unit polymerized) and 796 MPa (oven-polymerized); for BR-100, the values were 547 MPa and 689 MPa, respectively. Mean shear bond strength of composite resin cement to the FRC varied between 20.1 and 23.7 MPa, showing no statistical difference between the materials. SEM/EDS analysis revealed that fibers of both FRC materials consist of the same oxides (SiO2, CaO, and Al2O3) in ratios. The distribution of fibers in the cross section of specimens was more evenly distributed in everStick C&B than in BR-100. Conclusion. The results of this study suggest that there are some differences in the tested properties of the FRC materials.
Journal of Adhesion Science and Technology | 2011
Jukka Pekka Matinlinna; Pekka K. Vallittu; Lippo Lassila
The hydrolytic stability of various silane combinations and their effects on biomechanical properties and water sorption of an experimental dental composite made of bis-GMA and TEGDMA and silane-treated fillers were evaluated. Four silane coupling agents and their blends with a cross-linker silane were used as coupling agents for the 0.7-μm BaSiO3 fillers. The silanization was carried out in toluene containing 1% (v/v) of one of the four following organofunctional silane coupling agents: 3-acryloxypropyltrimethoxysilane, 3methacryloxypropyltrimethoxysilane, 3-styrylethyltrimethoxysilane and 3-isocyanatopropyltriethoxysilane. Blends of these functional silanes with 1% (v/v) of a cross-linker silane, 1,2- bis -(triethoxysilyl)ethane were also used for silanization. Composites were prepared by mixing 5.00 g Ba-glass filler with 2.00 g of a resin mixture consisting of bis-GMA (58.8 wt%) and TEGDMA (39.2 wt%) in a high-speed mixer. Threepoint bending test specimens (2.0 mm × 2.0 mm × 25.0 mm) were fabricated (n= 8) in a mould and photo-polymerized. The degree of conversion was measured with FT-IR. Biomechanical testing was carried out according to the ISO 10477 standard. Specimens were tested (flexural strength) after 30 days of water storage (37° C, distilled water). Water sorption and solubility (in wt%) were also measured on 1, 2, 3, 5, 7, 14, 21 and 30 days in water storage. Statistical analysis with ANOVA showed that the highest flexural strength was obtained when 3-acryloxypropyltrimethoxysilane + 1,2- bis -(triethoxysilyl)ethane (100.5 MPa; SD, 25.7 MPa) was used in the silanization step, and the lowest was obtained when 3isocyanatopropyltriethoxysilane + 1,2- bis-(triethoxysilyl)ethane (28.9 MPa; SD, 8.8 MPa) was used. The three-point bending strength was significantly affected by the functionality of the main silane tested (p< 0.05), but not by the addition of the cross-linker silane ( p> 0.05). The composite that had been silanized with 3-isocyanatopropyltriethoxysilane had the greatest amount of water uptake (1.75%), and the composite silanized with 3-methacryloxypropyltrimethoxysilane + 1,2- bis-(triethoxysilyl)ethane had the least (1.08%). In conclusion, selection of the functional silane monomer can be a significant factor in developing filled resin composites in dentistry.
Acta Odontologica Scandinavica | 2016
Ippei Hamanaka; Misa Iwamoto; Lippo Lassila; Pekka K. Vallittu; Hiroshi Shimizu; Yutaka Takahashi
Abstract Objective. The aim of this study was to evaluate the effect of cycling deflection on the flexural behavior of injection-molded thermoplastic resins. Materials and methods. Six injection-molded thermoplastic resins (two polyamides, two polyesters, one polycarbonate, one polymethyl methacrylate) and, as a control, a conventional heat-polymerized denture based polymer of polymethyl methacrylate (PMMA) were used in this study. The cyclic constant magnitude (1.0 mm) of 5000 cycles was applied using a universal testing machine to demonstrate plasticization of the polymer. Loading was carried out in water at 23ºC with eight specimens per group (n = 8). Cycling load (N) and deformation (mm) were measured. Results. Force required to deflect the specimens during the first loading cycle and final loading cycle was statistically significantly different (p < 0.05) with one polyamide based polymer (Valplast) and PMMA based polymers (Acrytone and Acron). The other polyamide based polymer (LucitoneFRS), polyester based polymers (EstheShot and EstheShotBright) and polycarbonate based polymer (ReigningN) did not show significant differences (p > 0.05). None of the materials fractured during the loading test. One polyamide based polymer (Valplast) displayed the highest deformation and PMMA based polymers (Acrytone and Acron) exhibited the second highest deformation among the denture base materials. Conclusion. It can be concluded that there were considerable differences in the flexural behavior of denture base polymers. This may contribute to the fatigue resistance of the materials.
Archive | 2002
Pekka Vallittu; Lippo Lassila; Mikael Skrifvas; Eeva K. Viljanen; Antti Ylu-Urpo
Archive | 2002
Timo Närhi; Antti Yli-Urpo; Pekka Vallittu; Marju Väkiparta; Teemu Tirri; Mervi Puska; Lippo Lassila; T.M Lastumäki; Allan Ho
Archive | 2002
Pekka Vallittu; Lippo Lassila; Antti Yli-Urpo
Archive | 2003
Pekka Vallittu; Lippo Lassila; llkka Kangasniemi
Archive | 2002
Pekka Vallittu; Lippo Lassila; Antti Yli-Urpo
Archive | 2004
Pekka Vallittu; Antti Yli-Urpo; Lippo Lassila; Timo Närhi; Tuomas Waltimo
Archive | 2003
Pekka Vallittu; Lippo Lassila; Ilkka Kangasniemi