Luc Thévenaz

Brillouin gain spectrum characterization in single-mode optical fibers

A novel method for Brillouin gain spectrum measurements in optical fibers is presented. It is based on the pump and probe technique with the specificity to use a single laser source together with an external modulator to generate the interacting lightwaves. The high accuracy and inherent stability of the technique makes it suitable for calibration and reference measurements. Different fibers with different refractive index profiles have been tested and characterized. The problem of the evolution of the polarization of the interacting waves is addressed in the article and a polarization insensitive determination of the actual Brillouin gain coefficient is made possible through two successive measurements with different polarizations. The effects of strain and temperature on the Brillouin gain spectrum are also fully characterized.

Observation of pulse delaying and advancement in optical fibers using stimulated Brillouin scattering

We demonstrate experimentally that it is possible to control optically the group velocity of an optical pulse as it travels along an optical fiber. To achieve this control we use the effect of Stimulated Brillouin Scattering. In our experiments we have achieved changes in the group index of 10-3 in several kilometer-length fibers, thus leading to pulse delaying and advancement in the range of tens of nanoseconds. We believe that this is the first evidence of such optically-controlled strong delay changes in optical fibers. In this paper we derive the basic theory behind these group-delay changes and we demonstrate the effect in two kinds of fibers which are conventionally used.

Distributed fiber‐optic temperature sensing for hydrologic systems

Instruments for distributed fiber-optic measurement of temperature are now available with temperature resolution of 0.01°C and spatial resolution of 1 m with temporal resolution of fractions of a minute along standard fiber-optic cables used for communication with lengths of up to 30,000 m. We discuss the spectrum of fiber-optic tools that may be employed to make these measurements, illuminating the potential and limitations of these methods in hydrologic science. There are trade-offs between precision in temperature, temporal resolution, and spatial resolution, following the square root of the number of measurements made; thus brief, short measurements are less precise than measurements taken over longer spans in time and space. Five illustrative applications demonstrate configurations where the distributed temperature sensing (DTS) approach could be used: (1) lake bottom temperatures using existing communication cables, (2) temperature profile with depth in a 1400 m deep decommissioned mine shaft, (3) air-snow interface temperature profile above a snow-covered glacier, (4) air-water interfacial temperature in a lake, and (5) temperature distribution along a first-order stream. In examples 3 and 4 it is shown that by winding the fiber around a cylinder, vertical spatial resolution of millimeters can be achieved. These tools may be of exceptional utility in observing a broad range of hydrologic processes, including evaporation, infiltration, limnology, and the local and overall energy budget spanning scales from 0.003 to 30,000 m. This range of scales corresponds well with many of the areas of greatest opportunity for discovery in hydrologic science.

Simple distributed fiber sensor based on Brillouin gain spectrum analysis

A novel configuration of a distributed fiber sensor by Brillouin gain analysis has been developed for temperature and strain monitoring. It uses a single laser source, and the required light signals are all generated with an electro-optic modulator, resulting in high stability and excellent reliability of the measuring setup. Measurement of the induced strain in a wound fiber is presented as a demonstration of the system performance.

Arbitrary-bandwidth Brillouin slow light in optical fibers

Brillouin slow light in optical fibers is a promising technique for the development of all-optical buffers to be used in optical routers. The main drawback of this technique up to now has been its narrow bandwidth, normally restricted to 35 MHz in conventional single-mode optical fibers. In this paper we demonstrate experimentally that Brillouin slow light with an arbitrary large bandwidth can be readily obtained in conventional optical fibers using a simple and inexpensive pump spectral broadening technique. In our experiments, we show the delaying of 2.7 ns pulses over slightly more than one pulse length with only some residual broadening (<25%) of the pulse width. We see no limit to extend this technique to the delaying of GHz-bandwidth signals.

Wavelength modulation spectroscopy: combined frequency and intensity laser modulation

A theoretical model of wavelength modulation spectroscopy that uses a laser diode on a Lorentzian absorption line is presented. This theory describes the general case of a current-modulated semiconductor laser, for which a combined intensity and frequency modulation with an arbitrary phase shift occurs. On the basis of this model, the effect of several modulation parameters on the detected signals is evaluated. Experimental signals measured on an absorption line of CO2 by use of a 2-microm distributed-feedback laser are also presented and validate this analysis. These experimental results agree with the calculated signals, confirming the relevance of the model.

Optically controlled slow and fast light in optical fibers using stimulated Brillouin scattering

We demonstrate a method to achieve an extremely wide and flexible external control of the group velocity of signals as they propagate along an optical fiber. This control is achieved by means of the gain and loss mechanisms of stimulated Brillouin scattering in the fiber itself. Our experiments show that group velocities below 71 000 kms on one hand, well exceeding the speed of light in vacuum on the other hand and even negative group velocities can readily be obtained with a simple benchtop experimental setup. We believe that the fact that slow and fast light can be achieved in a standard single-mode fiber, in normal environmental conditions and using off-the-shelf instrumentation, is very promising for a future use in real applications.

Vector analysis of stimulated Brillouin scattering amplification in standard single-mode fibers.

The polarization properties of stimulated Brillouin scattering (SBS) amplification or attenuation in standard single-mode fibers are examined through vectorial analysis, simulation and experiment. Vector propagation equations for the signal wave, incorporating SBS and birefringence, are derived and analyzed in both the Jones and Stokes spaces. The analysis shows that in the undepleted pump regime, the fiber may be regarded as a polarization-dependent gain (or loss) medium, having two orthogonal input SOPs, and corresponding two orthogonal output SOPs, for the signal, which, respectively, provide the signal with maximum and minimum SBS amplification (or attenuation). Under high Brillouin gain conditions and excluding zero-probability cases, the output SOP of arbitrarily polarized input signals, would tend to converge towards that of maximum SBS gain. In the case of high SBS attenuation the output SOP of an arbitrarily polarized signal would approach the output SOP corresponding to minimum attenuation. It is found that for a wide range of practical pump powers ( < or = 100mW) and for sufficiently long fibers with typical SBS and birefringence parameters, the signal aligned for maximum SBS interaction will enter/emerge from the fiber with its electric field closely tracing the same ellipse in space as that of the pump at the corresponding side of the fiber, albeit with the opposite sense of rotation. The analytic predictions are experimentally demonstrated for both Stokes (amplification) and anti-Stokes (attenuation) signals.

Modeling and evaluating the performance of Brillouin distributed optical fiber sensors

A thorough analysis of the key factors impacting on the performance of Brillouin distributed optical fiber sensors is presented. An analytical expression is derived to estimate the error on the determination of the Brillouin peak gain frequency, based for the first time on real experimental conditions. This expression is experimentally validated, and describes how this frequency uncertainty depends on measurement parameters, such as Brillouin gain linewidth, frequency scanning step and signal-to-noise ratio. Based on the model leading to this expression and considering the limitations imposed by nonlinear effects and pump depletion, a figure-of-merit is proposed to fairly compare the performance of Brillouin distributed sensing systems. This figure-of-merit offers to the research community and to potential users the possibility to evaluate with an objective metric the real performance gain resulting from any proposed configuration.

Simplex-coded BOTDA fiber sensor with 1 m spatial resolution over a 50 km range

In this Letter, we propose the use of optical pulse coding techniques for long-range distributed sensors based on Brillouin optical time-domain analysis (BOTDA). Compared to conventional BOTDA sensors, optical coding provides a significant sensing-range enhancement, allowing for temperature and strain measurements with 1 m spatial resolution over 50 km of standard single-mode fiber, with an accuracy of 2.2 degrees C/44 muepsilon, respectively.