Ludmilla Steier

Highly efficient planar perovskite solar cells through band alignment engineering

The simplification of perovskite solar cells (PSCs), by replacing the mesoporous electron selective layer (ESL) with a planar one, is advantageous for large-scale manufacturing. PSCs with a planar TiO2 ESL have been demonstrated, but these exhibit unstabilized power conversion efficiencies (PCEs). Herein we show that planar PSCs using TiO2 are inherently limited due to conduction band misalignment and demonstrate, with a variety of characterization techniques, for the first time that SnO2 achieves a barrier-free energetic configuration, obtaining almost hysteresis-free PCEs of over 18% with record high voltages of up to 1.19 V.

Monolithic perovskite/silicon-heterojunction tandem solar cells processed at low temperature

Tandem solar cells combining silicon and perovskite absorbers have the potential to outperform state-of-the-art high efficiency silicon single junction devices. However, the practical fabrication of monolithic silicon/perovskite tandem solar cells is challenging as material properties and processing requirements such as temperature restrict the device design. Here, we fabricate an 18% efficient monolithic tandem cell formed by a silicon heterojunction bottom- and a perovskite top-cell enabling a very high open circuit voltage of 1.78 V. The monolithic integration was realized via low temperature processing of the semitransparent perovskite sub-cell where an energetically aligned electron selective contact was fabricated by atomic layer deposition of tin oxide. The hole selective, transparent top contact was formed by a stack of the organic hole transport material spiro-OMeTAD, molybdenum oxide and sputtered indium tin oxide. The tandem cell design is currently limited by the photocurrent generated in the silicon bottom cell that is reduced due to reflectance losses. Based on optical modelling and first experiments, we show that these losses can be significantly reduced by combining optical optimization of the device architecture including light trapping approaches.

Highly efficient and stable planar perovskite solar cells by solution-processed tin oxide

Perovskite solar cells (PSCs) are one of the most promising lab-scale technologies to deliver inexpensive solar electricity. Low-temperature planar PSCs are particularly suited for large-scale manufacturing. Here, we propose a simple, solution-processed technological approach for depositing SnO2 layers. The use of these layers in planar PSCs yields a high stabilized power conversion efficiency close to 21%, exhibiting stable performance under real operating conditions for over 60 hours. In addition, this method yielded remarkable voltages of 1214 mV at a band gap of 1.62 eV (approaching the thermodynamic limit of 1.32 V) confirming the high selectivity of the solution-processed layers. PSCs aged under 1 sun illumination and maximum power point tracking showed a final PCE of 20.7% after ageing and dark storage, which is slightly higher than the original efficiency. This approach represents an advancement in the understanding of the role of electron selective layers on the efficiency and stability of PSCs. Therefore, the newly proposed approach constitutes a simple, scalable method paving the way for industrialization of perovskite solar cells.

Cu2O Nanowire Photocathodes for Efficient and Durable Solar Water Splitting

Due to its abundance, scalability, and nontoxicity, Cu2O has attracted extensive attention toward solar energy conversion, and it is the best performing metal oxide material. Until now, the high efficiency devices are all planar in structure, and their photocurrent densities still fall well below the theoretical value of 14.5 mA cm(-2) due to the incompatible light absorption and charge carrier diffusion lengths. Nanowire structures have been considered as a rational and promising approach to solve this issue, but due to various challenges, performance improvements through the use of nanowires have rarely been achieved. In this work, we develop a new synthetic method to grow Cu2O nanowire arrays on conductive fluorine-doped tin oxide substrates with well-controlled phase and excellent electronic and photonic properties. Also, we introduce an innovative blocking layer strategy to enable high performance. Further, through material engineering by combining a conformal nanoscale p-n junction, durable protective overlayer, and uniform catalyst decoration, we have successfully fabricated Cu2O nanowire array photocathodes for hydrogen generation from solar water splitting delivering unprecedentedly high photocurrent densities of 10 mA cm(-2) and stable operation beyond 50 h, establishing a new benchmark for metal oxide based photoelectrodes.

Efficient photosynthesis of carbon monoxide from CO2 using perovskite photovoltaics.

Artificial photosynthesis, mimicking nature in its efforts to store solar energy, has received considerable attention from the research community. Most of these attempts target the production of H2 as a fuel and our group recently demonstrated solar-to-hydrogen conversion at 12.3% efficiency. Here, in an effort to take this approach closer to real photosynthesis, which is based on the conversion of CO2, we demonstrate the efficient reduction of CO2 to carbon monoxide driven solely by simulated sunlight using water as the electron source. Employing series-connected perovskite photovoltaics and high-performance catalyst electrodes, we reach a solar-to-CO efficiency exceeding 6.5%, which represents a new benchmark in sunlight-driven CO2 conversion. Considering hydrogen as a secondary product, an efficiency exceeding 7% is observed. Furthermore, this study represents one of the first demonstrations of extended, stable operation of perovskite photovoltaics, whose large open-circuit voltage is shown to be particularly suited for this process.

On the stability enhancement of cuprous oxide water splitting photocathodes by low temperature steam annealing

Given the intermittent nature of solar radiation, the large-scale use of solar energy requires an efficient energy storage solution. So far, the only practical way to store such large amounts of energy is in the form of a chemical energy carrier, i.e., a fuel. Photoelectrochemical (PEC) cells offer the ability to convert solar energy directly into chemical energy in the form of hydrogen. Cuprous oxide (Cu2O) is being investigated for photoelectrochemical solar water splitting since it has a band gap of 2.0 eV with favorable energy band positions for water cleavage; it is abundant and environmentally friendly. A major challenge with Cu2O is its limited chemical stability in aqueous environments. We present a simple and low-cost treatment to create a highly stable photocathode configuration for H2 production, consisting of steam treatment of the multilayer structures. The role of this treatment was investigated and the optimized electrodes have shown photocurrents over −5 mA cm−2 with 90% stability over more than 50 h of light chopping (biased at 0 VRHE in pH 5 electrolyte).

Solution Transformation of Cu2O into CuInS2 for Solar Water Splitting

Though Cu2O has demonstrated high performance as a photocathode for solar water splitting, its band gap is too large for efficient use as the bottom cell in tandem configurations. Accordingly, copper chalcopyrites have recently attracted much attention for solar water splitting due to their smaller and tunable band gaps. However, their fabrication is mainly based on vacuum evaporation, which is an expensive and energy consuming process. Here, we have developed a novel and low-cost solution fabrication method, and CuInS2 was chosen as a model material due to its smaller band gap compared to Cu2O and relatively simple composition. The nanostructured CuInS2 electrodes were synthesized at low temperature in crystalline form by solvothermal treatment of electrochemically deposited Cu2O films. Following the coating of overlayers and decoration with Pt catalyst, the as-fabricated CuInS2 electrode demonstrated water splitting photocurrents of 3.5 mA cm(-2) under simulated solar illumination. To the best of our knowledge, this is the highest performance yet reported for a solution-processed copper chalcopyrite electrode for solar water splitting. Furthermore, the electrode showed good stability and had a broad incident photon-to-current efficiency (IPCE) response to wavelengths beyond 800 nm, consistent with the smaller bandgap of this material.

The effect of illumination on the formation of metal halide perovskite films

Optimizing the morphology of metal halide perovskite films is an important way to improve the performance of solar cells when these materials are used as light harvesters, because film homogeneity is correlated with photovoltaic performance. Many device architectures and processing techniques have been explored with the aim of achieving high-performance devices, including single-step deposition, sequential deposition and anti-solvent methods. Earlier studies have looked at the influence of reaction conditions on film quality, such as the concentration of the reactants and the reaction temperature. However, the precise mechanism of the reaction and the main factors that govern it are poorly understood. The consequent lack of control is the main reason for the large variability observed in perovskite morphology and the related solar-cell performance. Here we show that light has a strong influence on the rate of perovskite formation and on film morphology in both of the main deposition methods currently used: sequential deposition and the anti-solvent method. We study the reaction of a metal halide (lead iodide) with an organic compound (methylammonium iodide) using confocal laser scanning fluorescence microscopy and scanning electron microscopy. The lead iodide crystallizes before the intercalation of methylammonium iodide commences, producing the methylammonium lead iodide perovskite. We find that the formation of perovskite via such a sequential deposition is much accelerated by light. The influence of light on morphology is reflected in a doubling of solar-cell efficiency. Conversely, using the anti-solvent method to form methyl ammonium lead iodide perovskite in a single step from the same starting materials, we find that the best photovoltaic performance is obtained when films are produced in the dark. The discovery of light-activated crystallization not only identifies a previously unknown source of variability in opto-electronic properties, but also opens up new ways of tuning morphology and structuring perovskites for various applications.

Low-Temperature Atomic Layer Deposition of Crystalline and Photoactive Ultrathin Hematite Films for Solar Water Splitting

We developed a low-temperature atomic layer deposition route to deposit phase pure and crystalline hematite (α-Fe2O3) films at 230 °C without the need for postannealing. Homogenous and conformal deposition with good aspect ratio coverage was demonstrated on a nanostructured substrate and analyzed by transmission electron microscopy. These as-deposited α-Fe2O3 films were investigated as photoanodes for photoelectrochemical water oxidation and found to be highly photoactive. Combined with a TiO2 underlayer and a low-cost Ni(OH)2 catalyst, hematite films of less than 10 nm in thickness reached photocurrent densities of 0.3 mA cm(-2) at 1.23 V vs RHE and a photocurrent onset potential of less than 0.9 V vs RHE, previously unseen for films this thin and without high temperature annealing. In a thickness-dependent photoelectrochemical analysis, we identified a hematite thickness of only 10 nm to yield the highest internal quantum efficiency when using a suitable underlayer such as TiO2 that induces doping of the hematite film and reduces electron/hole recombination at the back contact. We find that, at high bias potentials, photocurrent density and quantum efficiency proportionally increase with light absorption in films thinner than 10 nm and are limited by the space charge layer width in thicker films. Thus, we propose to apply hematite films of 10 nm in thickness for future developments on suitable nanostructured conductive scaffolds that can now be extended to organic scaffolds due to our low-temperature process.

A copper nickel mixed oxide hole selective layer for Au-free transparent cuprous oxide photocathodes

State-of-the-art cuprous oxide (Cu2O) photocathodes for photoelectrochemical (PEC) water splitting have a long tradition of using gold (Au)-coated F-doped SnO2 (FTO) substrates for the improvement of Cu2O electrodeposition and overall PEC performance. Au is one of the best contact materials for Cu2O photocathodes due to its large work function enabling proper alignment with the valence band level of Cu2O. Due to its relatively large band gap (2.0 eV), Cu2O is preferentially used as the top-cell absorber in tandem with a photoanode or a photovoltaic (PV) cell for overall solar-driven water splitting. However, the Au contact poses a major issue due to its poor transparency. Moreover, Au is a precious metal, which increases the cost and can hinder the scalability of PEC devices. In this work, we propose an effective replacement of the Au layer with a transparent and cost-efficient copper-nickel mixed oxide (CuO/NiO) thin film, which is prepared by a facile sequential sputtering deposition combined with an annealing process in air. We successfully demonstrate that a thin layer of the CuO/NiO film shows better transparency as well as well-aligned energy levels for efficient hole collection leading to an improved PEC performance compared to the performance of a Au-contact based equivalent device in a pH 5 electrolyte biased at 0 V versus the reversible hydrogen electrode. This new transparent and efficient CuO/NiO layer paves the way for the development of efficient, yet inexpensive PEC–PV or photocathode–photoanode stacked tandem devices for a hydrogen fuel based economy.