Łukasz Piskorski

Room-temperature continuous-wave operation of the In(Ga)As/GaAs quantum-dot VCSELs for the 1.3 µm optical-fibre communication

Efficient room-temperature (RT) continuous-wave (CW) lasing operation of the 1.3 µm MBE (molecular-beam epitaxy) In(Ga)As/GaAs quantum-dot (QD) top-emitting oxide-confined vertical-cavity surface-emitting diode lasers (VCSELs) for the second-generation optical-fibre communication has been achieved. In their design, a concept of a QD inside a quantum well (QW) has been utilized. The proposed In(Ga)As/GaAs QD active region is composed of five groups of three 8 nm In0.15Ga0.85As QWs, each containing one InAs QD sheet layer. In each group located close to successive anti-node positions of the optical standing wave within the 3λ cavity, QWs are separated by 32 nm GaAs barriers. Besides, at both active-region edges, additional single InGaAs QWs are located containing single QD layers. For the 10 µm diameter QD VCSELs, the RT CW threshold current of only 6.2 mA (7.9 kA cm−2), differential efficiency of 0.11 W A−1 and the maximal output power of 0.85 mW have been recorded. The experimental characteristics are in excellent agreement with theoretical ones obtained using the optical-electrical-thermal-recombination self-consistent computer model. According to this, for the 10 µm devices, the fundamental linearly polarized LP01 mode remains the dominating one up to the current of 9.1 mA. The lowest RT CW lasing threshold below 5 mA is expected for 6 µm devices.

Self-consistent model of 650 nm GaInP/AlGaInP quantum-well vertical-cavity surface-emitting diode lasers

A comprehensive fully self-consistent model of oxide-confined GaAs-based vertical-cavity surface-emitting diode lasers (VCSELs) with GaInP/AlGaInP quantum-well active regions to simulate their room-temperature (RT) continuous-wave (CW) operation is presented. The model takes into consideration all observed or expected special features of GaInP/AlGaInP VCSELs. A complete set of model parameters is given. The model enables a deeper understanding of a VCSEL operation with full complexity of many inter-related physical phenomena taking place within its volume. It may also be used to design and optimize the above VCSEL structures for their numerous applications, in particular as sources of the 650 nm carrier wave in communication systems using plastic optical fibres. With the aid of this model, anticipated VCSEL RT CW performance characteristics may be determined.

Investigation of temperature characteristics of modern InAsP/InGaAsP multi-quantum-well TJ-VCSELs for optical fibre communication

Continuous-wave (CW) performance of modern 1.3-μm InAsP/InGaAsP multi-quantum-well (MQW) tunnel-junction vertical-cavity surface-emitting diode lasers (TJ-VCSELs) is investigated using our comprehensive self-consistent simulation model to suggest their optimal design for room and elevated temperatures. For increasing ambient temperatures, an increase in the VCSEL threshold current has happened to be mostly associated with the Auger recombination. Nevertheless, the InAsP/InGaAsP VCSELs have been found to exhibit encouraging thermal behaviour with the quite high value of maximal operating temperature of 350 K. It has been found that 5-μm devices seem to be the most optimal ones because they demonstrate both the room temperature (RT) threshold current equal to only 0.55 mA and maximum operating temperature equal to as much as 345 K. For these devices, the characteristic temperature T0 is equal to 92 K for 290–305 K, 51 K for 310–325 K and 29 K for 330–345 K. Therefore, the InAsP/InGaAsP VCSELs have been found to offer very promising performance both at room and elevated temperatures as sources of the carrier 1.3-μm wave in the fibre optical communication using silica fibres.

Analysis of anticipated performance of 650-nm GaInP/AlGaInP quantum-well GaAs-based VCSELs at elevated temperatures

The possibility of application of the 650-nm oxide-confined GaInP/AlGaInP quantum-well vertical-cavity surface-emitting diode lasers (VCSELs) at elevated temperatures as sources of the carrier 650-nm wave in the fibre optical communication using POFs has been investigated with the aid of the comprehensive self-consistent model. An increase in the VCSEL threshold current at higher temperatures has been found to be mostly associated with both the carrier leakage from the valley of the Ga0.43In0.57P quantum-well material to the X-valley of the (Al0.67Ga0.33)0.52In0.48P barriers and the band-to-band absorption within the Ga0.52In0.48P layer of the band-gap comparable with the energy of emitted radiation. Nevertheless, the AlGaInP VCSELs exhibit encouraging thermal behaviour with the characteristic temperature T0 equal to as much as 134 K for the active-region temperatures up to 357 K. For the 5-μm devices, the maximal achievable output has been determined to decrease from a quite high value of 1.0 mW for 293 K to 0.6 mW for 320 K and to still high 0.33 mW for 340 K. However, an efficient operation of the above VCSEL at elevated temperatures requires still some structure modifications leading to a reduction of both the above effects, the electron leakage from the valley and the band-to-band absorption within GaInP layers.

Structure optimisation of modern GaAs-based InGaAs/GaAs quantum-dot VCSELs for optical fibre communication

Room-temperature (RT) continuous-wave (CW) performance of modern 1300-nm oxide-confined In(Ga)As/GaAs quantum-dot (QD) vertical-cavity surface-emitting diode lasers (VCSELs) taking advantage of many QD sheets is investigated using our comprehensive self-consistent simulation model to suggest their optimal design. Obviously, quantum dots should be as uniform as possible and as dense as possible to ensure high enough optical gain. Besides, our simulation reveals that efficient and uniform current injection into VCSEL active regions necessary to enhance excitation of the desired fundamental LP01 mode is accomplished in the VCSEL configuration with the broad-area bottom contact and the ring upper one as well as with the oxide aperture localized within the first period of the upper p-type DBR. The doping of the DBR mirrors is chosen as a compromise between their high enough electrical conductivity and low enough free-carrier absorption. The oxide aperture is additionally introducing the radial optical waveguiding. Moreover, our analysis has been concluded that VCSEL active regions should be composed of at least 9 QD sheets to acquire efficient RT CW operation. Furthermore, rather longer optical cavities are recommended in this case because localization of QD sheets should be adjusted to the anti-node positions of the optical cavity standing wave.

VCSEL modeling with self-consistent models: From simple approximations to comprehensive numerical analysis

In the talk we show the process of modeling complete physical properties of VCSELs and we present a step-by-step development of its complete multi-physics model, gradually improving its accuracy. Then we introduce high contrast gratings to the VCSEL design, which strongly complicates its optical modeling, making the comprehensive multi-physics VCSEL simulation a challenging task. We show, however, that a proper choice of a self-consistent simulation algorithm can still make such a simulation a feasible one, which is necessary for an efficient optimization of the laser prior to its costly manufacturing.

The vertical-cavity surface-emitting laser incorporating a high contrast grating mirror as a sensing device

We propose a novel optical sensing system based on one device that both emits and detects light consisting of a verticalcavity surface-emitting laser (VCSEL) incorporating an high contrast grating (HCG) as a top mirror. Since HCGs can be very sensitive to the optical properties of surrounding media, they can be used to detect gases and liquid. The presence of a gas or a liquid around an HCG mirror causes changes of the power reflectance of the mirror, which corresponds to changes of the VCSEL’s cavity quality factor and current-voltage characteristic. By observation of the current-voltage characteristic we can collect information about the medium around the HCG. In this paper we investigate how the properties of the HCG mirror depend on the refractive index of the HCG surroundings. We present results of a computer simulation performed with a three-dimensional fully vectorial model. We consider silicon HCGs on silica and designed for a 1300 nm VCSEL emission wavelength. We demonstrate that our approach can be applied to other wavelengths and material systems.

Metalized monolithic high-contrast grating as a mirror for GaN-based VCSELs

In this paper, we present a novel design of a nitride-based VCSEL emitting at 414 nm and perform numerical analysis of optical, electrical and thermal phenomena. The bottom mirror of the laser is a Al(In)N/GaN DBR (Distributed Bragg Reflector), whereas the top mirror is realized as a semiconductor-metal subwavelength-grating, etched in GaN with silver stripes deposited between the stripes of the semiconductor grating. In this monolithic structure simulations show a uniform active-region current density on the level of 5.5 kA/cm2 for the apertures as large as 10 μm. In the case of a broader apertures, e.g. 40 μm, we showed that, assuming a homogeneous current injection at the level of 5.5 kA/cm2 , the temperature inside the laser should not exceed 360 K, which gives promise to improve thermal management by uniformisation of the current injection.

Numerical study of VECSELs for generation of mid-infrared radiation

Two different approaches to developing new laser sources operating in the mid-infrared range based on vertical-external cavity surface-emitting lasers (VECSELs) are studied with the aid of numerical modelling. The first one consists in enhancing a maximal emission wavelength of currently available GaSb-based structures beyond 3 μm. The second approach consists in using dual-wavelength VECSEL (DW-VECSEL), emitting two coaxial laser beams of different wavelengths, to generate radiation from the 3-5 μm spectral range with the aid of difference frequency generation.

Modelowanie i optymalizacja antymonkowych laserów typu VCSEL

In this work results of the threshold operation of antimonide-based vertical-cavity surface-emitting laser have been presented with the aid of the comprehensive fully self-consistent optical-electrical-thermal-recombination numerical model. Calculations have been carried out for the structure emitting at 2.6 μm. The advantages of incorporating the tunnel junction for current confinement have been shown and the influence of a layer shift caused by presence of the tunnel junction on the mode selectivity has been examined. It was shown that reducing the layer shift, with initial height equal to 55 nm, by the 35 nm leads to 7 and 25 times higher mode losses for LP11 and LP21 modes, respectively, and only 10% higher threshold current for the LP01 mode. Further reduction of the layer shift leads to high increment of the threshold current value: 20% for 40 nm reduction and 50% for 45 nm one. (Modelling and optimisation of the antimonide-based VCSELs). Słowa kluczowe: przyrządy półprzewodnikowe, lasery typu VCSEL, model numeryczny, obszar czynny GaInAsSb/GaSb, średnia podczerwień.