Łukasz Zinkiewicz

Transmission phase gratings fabricated with direct laser writing as color filters in the visible

Simple diffraction structures having the form of a regular grid of pillars can generate a significant range of hues in white light transmission due to color-dependent diffraction into higher orders. We present the fabrication of such submicrometer scale structures by three dimensional laser two-photon photolithography, results of their optical properties measurements and compare the latter with numerical simulations.

Highly asymmetric near infrared light transmission in an all-dielectric grating-on-mirror photonic structure.

We demonstrate a photonic structure, composed of a dielectric quarter-wavelength stack topped with a transmission phase grating, designed to exhibit a significant asymmetry in the near infrared light transmission for waves propagating in opposite directions. The asymmetry, defined as the difference between the intensity transmission coefficients, reaches 0.72 ± 0.06 for a single wavelength and exceeds 0.2 over a spectral range spanning from 700 to 850 nm for one incident polarization and 750-800 nm for both polarizations. The experimental results are consistent with the numerical model of light propagation in the structure.

Witnessing the pulse birth—transient dynamics in a passively mode-locked femtosecond laser

High temporal resolution measurements of the output of an Yb:KYW femtosecond laser, recorded immediately after opening the laser cavity, give an insight into the transient laser dynamics. The evolution of the light intensity measured with linear and nonlinear detectors, together with the time-resolved laser spectrum were measured and the process of the mode-locking onset was investigated. A phenomenological model of the laser dynamics has been developed that reproduces the experimental results.

Continuously tunable Yb:KYW femtosecond oscillator based on a tunable highly dispersive semiconductor mirror

The optimized nonuniform growth process was used to achieve spatially dependent reflectivity and dispersions characteristics in a highly dispersive semiconductor mirror. The mirror, together with a semiconductor saturable absorber mirror (SESAM), was used to demonstrate a tunable femtosecond Yb:KYW oscillator. In the passive modelocking regime the laser could be continuously tuned over 3.5 nm spectral band around 1032 nm with high resolution, maintaining the average output power above 140 mW.

Optical fiber micro-connector with nanometer positioning precision for rapid prototyping of photonic devices

Prototyping of fiber-coupled integrated photonic devices requires robust and reliable way of docking optical fibers to other structures, often with sub-micron accuracy. We have developed an optical fiber micro-connector 3D-printed with Direct Laser Writing on a planar substrate. The connector provides fiber core precision positioning better than 120 nm and sustains cryogenic cycling without any signs of degradation. It can be fabricated and used on glass and non-transparent substrates, including photonic integrated circuits, semiconductor samples, and microfluidic systems.

Saturable absorber mirrors for ytterbium mode-locked femtosecond lasers

The paper presents the way that colour can serve solving the problem of calibration points indexing in a camera geometrical calibration process. We propose a technique in which indexes of calibration points in a black-and-white chessboard are represented as sets of colour regions in the neighbourhood of calibration points. We provide some general rules for designing a colour calibration chessboard and provide a method of calibration image analysis. We show that this approach leads to obtaining better results than in the case of widely used methods employing information about already indexed points to compute indexes. We also report constraints concerning the technique. Nowadays we are witnessing an increasing need for camera geometrical calibration systems. They are vital for such applications as 3D modelling, 3D reconstruction, assembly control systems, etc. Wherever possible, calibration objects placed in the scene are used in a camera geometrical calibration process. This approach significantly increases accuracy of calibration results and makes the calibration data extraction process easier and universal. There are many geometrical camera calibration techniques for a known calibration scene [1]. A great number of them use as an input calibration points which are localised and indexed in the scene. In this paper we propose the technique of calibration points indexing which uses a colour chessboard. The presented technique was developed by solving problems we encountered during experiments with our earlier methods of camera calibration scene analysis [2]-[3]. In particular, the proposed technique increases the number of indexed points points in case of local lack of calibration points detection. At the beginning of the paper we present a way of designing a chessboard pattern. Then we describe a calibration point indexing method, and finally we show experimental results. A black-and-white chessboard is widely used in order to obtain sub-pixel accuracy of calibration points localisation [1]. Calibration points are defined as corners of chessboard squares. Assuming the availability of rough localisation of these points, the points can be indexed. Noting that differences in distances between neighbouring points in calibration scene images differ slightly, one of the local searching methods can be employed (e.g. [2]). Methods of this type search for a calibration point to be indexed, using a window of a certain size. The position of the window is determined by a vector representing the distance between two previously indexed points in the same row or column. However, experiments show that this approach has its disadvantages, as described below. * E-mail: A.Nowakowski@ire.pw.edu.pl Firstly, there is a danger of omitting some points during indexing in case of local lack of calibration points detection in a neighbourhood (e.g. caused by the presence of non-homogeneous light in the calibration scene). A particularly unfavourable situation is when the local lack of detection effects in the appearance of separated regions of detected calibration points. It is worth saying that such situations are likely to happen for calibration points situated near image borders. Such points are very important for the analysis of optical nonlinearities, and a lack of them can significantly influence the accuracy of distortion modelling. Secondly, such methods may give wrong results in the case of optical distortion with strong nonlinearities when getting information about the neighbouring index is not an easy task. Beside this, the methods are very sensitive to a single false localisation of a calibration point. Such a single false localisation can even result in false indexing of a big set of calibration points. To avoid the above-mentioned problems, we propose using a black-and-white chessboard which contains the coded index of a calibration point in the form of colour squares situated in the nearest neighbourhood of each point. The index of a certain calibration point is determined by colours of four nearest neighbouring squares (Fig.1). An order of squares in such foursome is important. Because the size of a colour square is determined only by the possibility of correct colour detection, the size of a colour square can be smaller than the size of a black or white square. The larger size of a black or white square is determined by the requirements of the exact localisation step which follows the indexing of calibration points [3]. In this step, edge information is extracted from a blackand-white chessboard. This edge information needs larger Artur Nowakowski, Wladyslaw Skarbek Institute of Radioelectronics, Warsaw University of Technology, Nowowiejska 15/19, 00-665 Warszawa, A.Nowakowski@ire.pw.edu.pl Received February 10, 2009; accepted March 27, 2009; published March 31, 2009 http://www.photonics.pl/PLP

Measurement of the mass of an object hanging from a spring?revisited

In an open competition, students were to determine the mass of a metal cylinder hanging on a spring inside a transparent enclosure. With the time for experiments limited to 24 h due to the unexpectedly large number of participants, a few surprisingly accurate results were submitted, the best of them differing by no more than 0.5% from the true value with a relative uncertainty of less than 1%.