M.A. Lopez-Anton

Application of thermal desorption for the identification of mercury species in solids derived from coal utilization

The speciation of mercury is currently attracting widespread interest because the emission, transport, deposition and behaviour of toxic mercury species depend on its chemical form. The identification of these species in low concentrations is no easy task and it is even more complex in coal combustion products due to the fact that these products contain organic and mineral matter that give rise to broad peaks and make it difficult to carry out qualitative and quantitative analysis. In this work, a solution to this problem is proposed using a method based on thermal desorption. A sequential extraction procedure was employed for the comparison and validation of the method developed. Samples of fly ashes and soils were analyzed by both of these methods, and thermal desorption was found to be an appropriate technique for mercury speciation. Even in the case of low mercury contents, recovery percentages were close to 100%. The main mercury species identified in the samples studied were HgS and, to a lesser extent, HgO and HgSO4. In addition, although the presence of mercury complexes cannot be demonstrated, the desorption behaviour and sequential extraction results suggest that this element might be associated with the mineral matrix or with carbon particles in some of the solids.

Biomass gasification chars for mercury capture from a simulated flue gas of coal combustion.

The combustion of coal can result in trace elements, such as mercury, being released from power stations with potentially harmful effects for both human health and the environment. Research is ongoing to develop cost-effective and efficient control technologies for mercury removal from coal-fired power plants, the largest source of anthropogenic mercury emissions. A number of activated carbon sorbents have been demonstrated to be effective for mercury retention in coal combustion power plants. However, more economic alternatives need to be developed. Raw biomass gasification chars could serve as low-cost sorbents for capturing mercury since they are sub-products generated during a thermal conversion process. The aim of this study was to evaluate different biomass gasification chars as mercury sorbents in a simulated coal combustion flue gas. The results were compared with those obtained using a commercial activated carbon. Chars from a mixture of paper and plastic waste showed the highest retention capacity. It was found that not only a high carbon content and a well developed microporosity but also a high chlorine content and a high aluminium content improved the mercury retention capacity of biomass gasification chars. No relationship could be inferred between the surface oxygen functional groups and mercury retention in the char samples evaluated.

A comparison of devices using thermal desorption for mercury speciation in solids

The goal of this work is to emphasize the reliability of the thermal desorption technique in identifying mercury species. The analysis of mercury species in solids is essential for assessing the risk of disposal or re-use of mercury-contaminated materials. This study evaluates the accuracy and reliability of thermal desorption as a technique for identifying mercury species by means of different thermo-desorption devices. For this purpose, mercury species present in samples related with coal utilization processes were identified. Three devices were compared for analyzing samples free of carbon or with a low carbon content (fly ashes, gypsums and soils), and a new equipment was developed to analyze samples with a high carbon content (coal). In spite of the fact that the first three devices employ different experimental conditions (i.e., heating rate, gas flow and carrier gas), the mercury species identified in the samples were comparable in all cases. The need for new equipment for mercury speciation in materials containing carbon was a consequence of interferences produced from the pyrolysis products of the organic matter. The new device consists of two furnaces and two gas inlets to allow thermal oxidation of organic pyrolysis products and the identification of mercury species in carbonaceous samples. This new approach offers the application of thermal desorption to mercury speciation in all types of materials contaminated with mercury.

Impact of oxy-fuel combustion gases on mercury retention in activated carbons from a macroalgae waste: Effect of water

The aim of this study is to understand the different sorption behaviors of mercury species on activated carbons in the oxy-fuel combustion of coal and the effect of high quantities of water vapor on the retention process. The work evaluates the interactions between the mercury species and a series of activated carbons prepared from a macroalgae waste (algae meal) from the agar-agar industry in oxy-combustion atmospheres, focussing on the role that the high concentration of water in the flue gases plays in mercury retention. Two novel aspects are considered in this work (i) the impact of oxy-combustion gases on the retention of mercury by activated carbons and (ii) the performance of activated carbons prepared from biomass algae wastes for this application. The results obtained at laboratory scale indicate that the effect of the chemical and textural characteristics of the activated carbons on mercury capture is not as important as that of reactive gases, such as the SOx and water vapor present in the flue gas. Mercury retention was found to be much lower in the oxy-combustion atmosphere than in the O2+N2 (12.6% O2) atmosphere. However, the oxidation of elemental mercury (Hg0) to form oxidized mercury (Hg2+) amounted to 60%, resulting in an enhancement of mercury retention in the flue gas desulfurization units and a reduction in the amalgamation of Hg0 in the CO2 compression unit. This result is of considerable importance for the development of technologies based on activated carbon sorbents for mercury control in oxy-combustion processes.

The stability of arsenic and selenium compounds that were retained in limestone in a coal gasification atmosphere

The aim of this work was to evaluate the stability of arsenic and selenium species retained in a lime/limestone mixture obtained by using limestone as a sorbent for gas cleaning in a coal gasification atmosphere. It was found that the stability of arsenic and selenium species produced by the gas-solid reactions with lime/limestone may be affected by their exposure to air and by their contact with water. The results confirm the conclusions of a previous work in which Ca(AsO(2))(2) and CaSe was postulated as the products of the reaction between the arsenic and selenium species present in a coal gasification atmosphere with lime/limestone. Moreover it was proved that the compounds (Ca(AsO(2))(2) and CaSe) may undergo transformations when the sorbents post-retention are stored or disposed of in air. From the results obtained by XAFS it was possible to identify the Ca(3)(AsO(4))(2) produced by the oxidation of the Ca(AsO(2))(2) on the sorbent surface. The XAFS results for selenium showed that the CaSe formed on the sorbent was transformed to form several species, but mainly elemental Se. These changes in the speciation of arsenic and selenium may explain the behavior of the sorbent post-retention during the water solubility test. Although the selenium compounds and the products that may originate from their decomposition in water are not toxic, in the case of arsenic, species like Ca(AsO(2))(2) and Ca(3)(AsO(4))(2) may lixiviate, and generate toxic arsenic compounds in solution that could pose a risk when the sorbent is finally disposed of.

Leaching of major and trace elements from paper-plastic gasification chars: an experimental and modelling study.

The control of soluble metal species in the sub-product leachate generated in electricity production processes is of great concern from an environmental and health point of view. Unlike fly ash, the leaching behaviour of char materials has received little attention. Yet, these solids are captured together with fly ashes in the particle control devices of power plants and are emitted in the same way as by-products. The present study was carried out using two char samples: (i) a raw char and (ii) the same type of char employed in a previous study so that it could serve as a sorbent for mercury species in gas phase. The char samples were by-products (residues) that had been generated during the gasification of plastic and paper waste. The leachates were analyzed for the following elements: Al, Ca, Si, Mg, Ba, Cu, Ni, Pb, Zn, Mo and Hg. In addition, geochemical modelling of the leaching test results was employed to identify the underlying chemical processes that led to the release of toxic elements. The results showed that at alkaline pH values, sorption on the solid surfaces of the char was negligible due to the inorganic complexation of cations in the solution. When the char was used as mercury sorbent slight changes occurred on the reactive surface resulting in the modification of the binding of some elements. As the pH increased, complexation with dissolved organic matter played a more important role in the case of some elements such as Cu because of the greater concentration of dissolved organic matter in solution.