M. Carmo Lança

Study of Electrical Properties of Natural Cork and Two Derivative Products

Electrical properties of natural cork, commercial cork agglomerates (for floor and wall coverings) and a recently developed composite of cork/TetraPak® were studied. Measurements of isothermal charge and discharge currents were made for natural cork samples in different directions (axial, radial and tangential cuts). The isothermal current characteristics and the samples conductivity were investigated under different conditions (electric field, temperature and environmental conditions: in air at ambient relative humidity (RH), dry air and vacuum), also the samples could be or not conditioned (dried in vacuum or in a P2O5 atmosphere at room temperature). From these results the influence of water on the electrical properties of natural cork could be seen. In order to compare the three different cork materials a preliminary study was made. Isothermal charge and discharge currents and conductivity after 1h charging were measured and compared for different electric fields and temperature in air at ambient RH.

The determination of the metal-dielectric interface barrier height from the open-circuit isothermal charging current

There is a sustained interest both from theoretical and from practical points of view to understand the isothermal charging and the isothermal discharging currents in dielectrics. The measured currents are analyzed either in terms of polarization mechanisms or in terms of charge injection/extraction at the metal-dielectric interface and the conduction current through the dielectric material. As long as we do not know the nature of the origin of the current, it is not clear what information we can get by analyzing the experimental data. We propose to measure the open-circuit isothermal charging and discharging currents just to overpass the difficulties related to the analysis of the conduction mechanisms in dielectric materials. We demonstrate that besides a polarization current, there is a current related with charge injection or extraction at the metal-dielectric contact and a reverse current related to the charge trapped into the superficial trap states of the dielectric and that can jump at the interfa...

Space Charge Studies of Aged XLPE Using Combined Isothermal and Thermostimulated Current Measurements

Space charge in electrically aged cross-linked polyethylene (XLPE) was studied using a procedure combining isothermal and non-isothermal measurements of charge and discharge currents. Aging is carried out using an AC field while immersing the disk-shaped samples in an ionic aqueous solution at constant temperature. After aging the samples were isothermally DC charged and discharged. Next a non-isothermal experiment with constant heating rate was performed (FTSDC). Finally the sample was kept at the highest temperature in order to completely discharge the polymer. The space charge introduced in the XLPE during aging can be analyzed from the study of the FTSDC spectra. The thermogram (FTSDC) shows a very broad peak. The peak is attributed to trapped space charge in traps with long relaxation times. It is possible to decompose it into three or four individual peaks and obtain the corresponding activation energies. The results were compared with previous ones obtained for LDPE (low density polyethylene) aged under similar conditions.

Dielectric Properties of Electrically Aged Low Density Polyethylene

Low density polyethylene (LDPE) films kept in a sodium chloride aqueous solution, were aged under a high AC electrical field. The films were prepared from press moulding of LDPE pellets with small amounts of antioxidants. The dielectric spectra at 30 o C in the range of 10 -5 Hz to 10 5 Hz were obtained prior and after ageing. Three different experimental techniques were used to obtain the full spectrum. For the low frequency (LF) region (10 -5 Hz to 10 -1 Hz) the time domain technique was used (charge and discharge currents were also measured). The measuring device used for the 10 -1 Hz to 10 1 Hz medium frequency (MF) region was a lock-in amplifier. While for the high frequency (HF), 10 -1 Hz to 10 5 Hz, RLC bridge measurements were performed. Differences can be seen between aged and unaged PE. The region showing less changes with ageing is the MF region where the peak of the unaged samples seems to become less defined with ageing time. This peak is probably due to additives and impurities (such as antioxidants) that will tend to slowly diffuse out with time. The LF peak is a broad peak related to localised space charge injection driven by the electric field. This peak increases in an earlier stage of ageing decreasing afterwards possibly when the polymer becomes more conductive. Finally the HF shows the beginning of a peak due to and transitions. The later is related to dipolar rotation of carbonyl groups in amorphous polymer regions, while the former is associated to crankshaft motions in the main polymer chain. This peak decreases with ageing disappearing for the most aged samples. This could also be explained if the sample becomes more conductive.

Electrical Properties Studies of a Cork/TetraPak®/Paraffin Wax Composite

Lately the electrical and dielectric properties of cork and some cork-based materials (commercial and non-commercial) have been studied in order to understand their ability to store electrical charge. The main problem found so far is related to the water content in cork, only of a few % weight, but large enough to influence greatly the conductivity of cork and, consequently, the charge storage capability. To overcome this problem cork has been combined with hydrophobic materials. In this work a commercial wax (paraffin wax) was used to produce a cork/paraffin composite by hot pressing. After milled and mixed natural cork, TetraPak® containers waste and paraffin were pressed to make plaques of a new composite. Different concentrations of cork, TetraPak® and paraffin, different granules size, different temperature and pressure were used to produce the samples. The electrical properties of the new composite were measured by the isothermal charging and discharging current method and the results compared to previously ones obtained for natural cork and other derivative products. The new composite has shown to have lower conductivity than the commercial agglomerate, which makes it a better material for charge storage.

The determination of the pull-in voltage from the condition of bridge stability

An analytical expression for the pull-in voltage is deduced for an RF micro-electromechanical system (MEMS) switch, by tacking into account the presence of a dielectric layer deposited on the coplanar waveguide. The model allows investigation of the influence of the dielectric permittivity and the geometry of the device on the displacement d of the bridge and on the pull-in voltage. A comparison of the experimental data and the simulated data gives indication about the best way to estimate the pull-in voltage. The difference between the value obtained for the pull-in voltage, when the contribution of the dielectric layer is taken into account and the value of the pull-in voltage obtained by neglecting the presence of the dielectric layer is significant indicating that the presence of the dielectric layer cannot be neglected.

New Experimental Facts Concerning the Thermally Stimulated Discharge Current in Dielectric Materials

The thermally stimulated discharge current (TSDC) method is a very sensitive and a very selective technique to analyze dipole disorientation and the movement of de-trapped space charge (SC). We have proposed a variant of the TSDC method, namely the final thermally stimulated discharge current (FTSDC) technique. The experimental conditions can be selected so that the FTSDC is mainly determined by the SC de-trapping. The temperatures of the maximum intensity of the fractional polarization peaks obtained at low temperature, in the range of the local (secondary) relaxation, are in general about 10 to 20 K above the poling temperature. Measurements of the FTSDC in a wide temperature range demonstrate the existence of an apparent peak at a temperature Tma shifted with about 10 to 30 K above the charging temperature Tc. The shift of Tma with respect to Tc depends on the experimental conditions. The peak width at the half maximum intensity decreases as Tc increases and the thermal apparent activation energy increases. The variations are not monotonous revealing the temperature range where the molecular motion is stronger and consequently the charge trapping and de-trapping processes are affected. Our results demonstrate that there is a strong similarity between the elementary peaks obtained by the two methods, and the current is mainly determined by SC de-trapping. Even the best elementary peaks are not fitted very well by the analytical equation, indicating that the hypothesis behind this equation have to be reconsidered.

Space Charge Studies in XLPE from Power Cables Using Combined Isothermal and Thermostimulated Current Measurements

Cross-linked polyethylene (XLPE) peelings from aged power cables from three different sources were studied using a combined procedure of isothermal and thermo-stimulated current measurements. Different parameters, such as electric field, temperature, charging/discharging times, can be selected in order to make an analysis of the space charge characteristics (such as, relaxation times and activation energies). Three different cables peelings were analyzed: A – electrically aged in the laboratory at high temperature, B – service aged for 18 years and C – thermally aged in the laboratory at high temperature. The results were compared for the different types of samples and also with previous results on laboratory aged and produced films of low-density polyethylene (LDPE) and XLPE.

Comparative study of space charge in aged low-density polyethylene and crosslinked polyethylene

Polyethylene is one of the most widely used polymeric insulators in medium and high voltage power cables. However the importance of space charge distribution and its influence on the electrical aging in this polymer is not fully understood. The very good insulating properties of the material implying very long relaxation times (few days and even longer are usual) and low currents (few pA or below) make individual measurements of isothermal charge/discharge currents and thermostimulated currents difficult to analyze and reproduce. A single type of measurements does not take into account the space charge that remains trapped for long times. A combined procedure of isothermal and non-isothermal current measurements developed for high insulating polymers was used for low density polyethylene (LDPE) and crosslinked polyethylene (XLPE) films electrically aged. The press-molded LDPE and XLPE films were electrically aged under similar conditions using an AC electric field while immersed in a sodium chloride aqueous solution at constant temperature (electro-thermal aging). The use of the combined procedure for current measurement allowed obtaining information about space charge traps, activation energies and relaxation times for both LDPE and XLPE. This data was used to compare electrical aging under similar conditions for the two types of polyethylene.

Dielectric Breakdown Statistics of Polyethylene for Progressively-Censored Data

The dielectric breakdown of thin films of low-density polyethylene (LDPE) electrically aged in an aqueous solution of NaCl under an AC electric field was investigated. A two-parameter Weibull function was used for the dielectric breakdown time to failure. The probability of failure for a sample was obtained by the White method for progressively censored data. Samples aged at different temperatures were compared. The results show that initially the samples aged at lower temperature ( 25C) are more prone to fail, while those aged at higher temperature (50 C) fail at longer times. This was attributed to a competition between oxidation and diffusion.