M. Kalish

Exploration of Spherical Torus Physics in the NSTX Device

The National Spherical Torus Experiment (NSTX) is being built at the Princeton Plasma Physics Laboratory to test the fusion physics principles for the Spherical Torus (ST) concept at the MA level. The NSTX nominal plasma parameters are R {sub 0} = 85 cm, a = 67 cm, R/a greater than or equal to 1.26, B {sub T} = 3 kG, I {sub p} = 1 MA, q {sub 95} = 14, elongation {kappa} less than or equal to 2.2, triangularity {delta} less than or equal to 0.5, and plasma pulse length of up to 5 sec. The plasma heating/current drive (CD) tools are High Harmonic Fast Wave (HHFW) (6 MW, 5 sec), Neutral Beam Injection (NBI) (5 MW, 80 keV, 5 sec), and Coaxial Helicity Injection (CHI). Theoretical calculations predict that NSTX should provide exciting possibilities for exploring a number of important new physics regimes including very high plasma beta, naturally high plasma elongation, high bootstrap current fraction, absolute magnetic well, and high pressure driven sheared flow. In addition, the NSTX program plans to explore fully noninductive plasma start-up, as well as a dispersive scrape-off layer for heat and particle flux handling.

Measurements of tritium retention and removal on the Tokamak Fusion Test Reactor

Recent experiments on the Tokamak Fusion Test Reactor have afforded an opportunity to measure the retention of tritium in a graphite limiter that is subject to erosion, codeposition, and high neutron flux. The tritium was injected by both gas puff and neutral beams. The isotopic mix of hydrogenic recycling was measured spectroscopically and the tritium fraction T/(H+D+T) transiently increased to as high as 75%. Some tritium was pumped out during the experimental run and some removed in a subsequent campaign using various clean‐up techniques. While the short term retention of tritium was high, various conditioning techniques were successful in removing ≊8000 Ci and restoring the tritium inventory to a level well below the administrative limit.

Engineering design of the National Spherical Torus Experiment

NSTX is a proof-of-principle experiment aimed at exploring the physics of the ‘spherical torus’ (ST) configuration, which is predicted to exhibit more efficient magnetic confinement than conventional large aspect ratio tokamaks, among other advantages. The low aspect ratio (R:a, typically 1.2‐2 in ST designs compared to 4‐5 in conventional tokamaks) decreases the available cross sectional area through the center of the torus for toroidal and poloidal field coil conductors, vacuum vessel wall, plasma facing components, etc., thus increasing the need to deploy all components within the so-called ‘center stack’ in the most efficient manner possible. Several unique design features have been developed for the NSTX center stack, and careful engineering of this region of the machine, utilizing materials up to their engineering allowables, has been key to meeting the desired objectives. The design and construction of the machine has been accomplished in a rapid and cost effective manner thanks to the availability of extensive facilities, a strong experience base from the TFTR era, and good cooperation between institutions.

Update on Design of the ITER In-Vessel Coils

Abstract The ITER project baseline now includes two sets of in-vessel coils, one to mitigate the effects of Edge Localized Modes (ELMs) and another to provide vertical stabilization (VS). The in-vessel location presents special challenges in terms of nuclear radiation and temperature, and requires the use of mineral-insulated conductors. An update to the preliminary design based on this conductor technology is presented for both coil designs. Results from an on-going R&D program consisting of conductor development, welding and brazing process development, electrical testing and mechanical testing in order to demonstrate manufacturability of this style of conductor are presented. Plans for two prototype coils, one of each type, are presented.

A Neutral Beam Injector Upgrade for NSTX

The National Spherical Torus Experiment (NSTX) capability with a Neutral Beam Injector (NBI) capable of 80 kiloelectronvolt (keV), 5 Megawatt (MW), 5 second operation. This 5.95 million dollar upgrade reused a previous generation injector and equipment for technical, cost, and schedule reasons to obtain these specifications while retaining a legacy capability of 120 keV neutral particle beam delivery for shorter pulse lengths for possible future NSTX experiments. Concerns with NBI injection included power deposition in the plasma, aiming angles from the fixed NBI fan array, density profiles and beam shine through, orbit losses of beam particles, and protection of the vacuum vessel wall against beam impingement. The upgrade made use of the beamline and cryo panels from the Neutral Beam Test Stand facility, existing power supplies and controls, beamline components and equipment not contaminated by tritium during DT [deuterium-tritium] experiments, and a liquid Helium refrigerator plant to power and cryogenically pump a beamline and three ion sources. All of the Tokamak Fusion Test Reactor (TFTR) ion sources had been contaminated with tritium, so a refurbishment effort was undertaken on selected TFTR sources to rid the three sources destined for the NSTX NBI of as much tritium as possible. An interconnecting duct was fabricated using some spare and some new components to attach the beamline to the NSTX vacuum vessel. Internal vacuum vessel armor using carbon tiles was added to protect the stainless steel vacuum vessel from beam impingement in the absence of plasma and interlock failure. To date, the NBI has operated to 80 keV and 5 MW and has injected requested power levels into NSTX plasmas with good initial results, including high beta and strong heating characteristics at full rated plasma current.

Design and Analysis of the ITER Vertical Stability (VS) Coils

Abstract The ITER vertical stability (VS) coils have been developed through the preliminary design phase by Princeton Plasma Physics Laboratory (PPPL). Final design, prototyping and construction will be carried out by the Chinese Participant Team contributing lab, Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP). The VS coils are a part of the in-vessel coil systems which include edge localized mode (ELM) coils as well as the VS coils. The VS design employs four turns of stainless steel jacketed mineral insulated copper (SSMIC) conductors The mineral insulation is Magnesium Oxide (MgO). Joule and nuclear heat are removed by water flowing through the hollow copper conductor. The slightly elevated temperatures in the conductor and its support spine during operation impose compressive stresses that mitigate fatigue damage. Away from joints, and breakouts, conductor thermal stresses are low because of the axisymmetry of the winding (there are no corner bends as in the ELM coils).The joints, and break-out or terminal regions are designed with similar but imperfect constraint compared with the ring coil portion of the VS. The support for the break-out region is made from a high strength copper alloy, CuCrZr. This is needed to conduct nuclear heat to the actively cooled conductor and to the vessel wall. The support “spine” for the ring coil portion of the VS is 316 stainless steel, held to the vessel with preloaded Inconel 718 bolts. Lorentz loads resulting from normal operating loads, disruption loads and loads from disruption currents in the support spine shared with vessel, are applied to the VS coil. Stresses in the coil, joints, and break-outs are presented. These are compared with static and fatigue allowables. Design for fatigue is much less demanding than for the ELM coils. A total of 30,000 cycles is required for VS design.

Operation of the tokamak fusion test reactor tritium systems during initial tritium experiments

Abstract The high power D-T experiments on the tokamak fusion test reactor (TFTR) at the Princeton Plasma Physics Laboratory commenced in November 1993. During initial operation of the tritium systems a number of start-up problems surfaced and had to be corrected. These were corrected through a series of system modifications and upgrades and by repair of failed or inadequate components. Even as these operational concerns were being addressed, the tritium systems continued to support D-T operations on the tokamak. During the first six months of D-T operations more than 107 kCi of tritium were processed successfully by the tritium systems. D-T experiments conducted at TFTR during this period provided significant new data. Fusion power in excess of 9 MW was achieved in May 1994. This paper describes some of the early start-up issues, and reports on the operation of the tritium system and the tritium tracking and accounting system during the early phase of TFTR D-T experiments.

Design and construction of the NSTX bakeout, cooling and vacuum systems

This paper will describe the design, construction and initial operation of the NSTX bakeout, water cooling and vacuum systems. The bakeout system is designed for two modes of operation. The first mode allows heating of the first wall components to 350/spl deg/C while the external vessel is cooled to 150/spl deg/C. The second mode cools the first wall to 150/spl deg/C and the external vessel to 50/spl deg/C. The system uses a low viscosity heat transfer oil which is capable of high temperature low pressure operation.

Preliminary Thermal and Hydraulic Analysis on the ITER Upper Diagnostic Port Plug During Normal Operation and Baking

A preliminary thermo-hydraulic analysis was performed on the ITER diagnostic upper port plug. Relevant thermal and hydraulic parameters, such as coolant pressure drop, maximum structure temperature and bake-out time, were calculated for normal operation and baking. The upper port plug considered is based on the preliminary generic structure design of Princeton Plasma Physics Laboratory and the Blanket Shield Module (BSM) developed in Europe. The diagnostic shield modules are modeled so that the Korean diagnostic procurement package, which includes Vacuum Ultra-Violet (VUV) spectrometer and neutron activation system, can be integrated. The analysis provides design inputs to optimize flow in the cooling channels of the plug. The conjugated heat transfer analysis for the port plug confirms that it is important to secure accurate nuclear heat and accurate electro-magnetic (EM) force for the design of the joining flange between the BSM and the main body. Thermal analysis shows that it will take ten hours for the port plug to reach the bake-out temperature (240°C), if the window plate is heated additionally from the rear side.

Making of the NSTX facility

The NSTX (National Spherical Torus Experiment) facility located at Princeton Plasma Physics Laboratory is the newest national fusion science experimental facility for the restructured US Fusion Energy Science Program. The NSTX project was approved in FY 97 as the first proof-of-principle national fusion facility dedicated to the spherical torus research. On Feb. 15, 1999, the first plasma was achieved 10 weeks ahead of schedule. The project was completed on budget and with an outstanding safety record. This paper gives an overview of the NSTX facility construction and the initial plasma operations.