Mahtab Asadian

Surface Treatment of PEOT/PBT (55/45) with a Dielectric Barrier Discharge in Air, Helium, Argon and Nitrogen at Medium Pressure

This work describes the surface modification of 300PEO-PEOT/PBT 55/45 thin films using a medium pressure dielectric barrier discharge system operated in argon, helium, nitrogen or dry air to improve cell-surface interactions of this established biomaterial. The first part of the paper describes the optimization of the plasma processing parameters using water contact angle goniometry. The optimized samples are then characterized for changes in surface topography and surface chemical composition using atomic force microscopy (AFM) and X-ray fluorescence spectroscopy (XPS) respectively. For all plasma treatments, a pronounced increase in surface wettability was observed, of which the extent is dependent on the used plasma discharge gas. Except for dry air, only minor changes in surface topography were noted, while XPS confirmed that the changes in wettability were mainly chemical in nature with the incorporation of 5–10% of extra oxygen as a variety of polar groups. Similarly, for the nitrogen plasma, 3.8% of nitrogen polar groups were additionally incorporated. Human foreskin fibroblast (HFF) in vitro analysis showed that within the first 24 h after cell seeding, the effects on cell-surface interactivity were highly dependent on the used discharge gas, nitrogen plasma treatment being the most efficient. Differences between untreated and plasma-treated samples were less pronounced compared to other biodegradable materials, but a positive influence on cell adhesion and proliferation was still observed.

Micropatterning of beta tricalcium phosphate bioceramic surfaces, by femtosecond laser, for bone marrow stem cells behavior assessment

The bioactivity of synthetic bone implants is highly impacted by their surface topography, especially by the presence of micro-patterns likely to generate cells growth guidance. In this study, laser machining technology was employed in order to produce controlled regular micro-patterns on dense calcium phosphate surfaces, without any contamination. The choice of the source was directed towards a femtosecond pulsed laser in order to limit the thermal impact of such a process and thus to avoid the unwanted phase transformations potentially induced by the temperature elevation. Beta tricalcium phosphate substrates with perfectly controlled micro-patterning and without any secondary phase were obtained by optimization of the process parameters (laser power, scanning speed, pulse frequency). The microstructural characteristics were investigated by microscopy (optical, confocal, scanning electron) and the phase identification was performed by X-ray diffraction. This work allowed highlighting the effects of the process parameters on the patterning. The high benefits of the laser treatment on wettability were shown by contact angle assays. Finally, the influence of surface micro-patterning on cell behavior was highlighted in vitro. This technique seems to provide an interesting alternative to conventional surface treatments of calcium phosphates.

Improving the surface properties of an UHMWPE shoulder implant with an atmospheric pressure plasma jet

Insufficient glenoid fixation is one of the main reasons for failure in total shoulder arthroplasty. This is predominantly caused by the inert nature of the ultra-high molecular weight polyethylene (UHMWPE) used in the glenoid component of the implant, which makes it difficult to adhesively bind to bone cement or bone. Previous studies have shown that this adhesion can be ameliorated by changing the surface chemistry using plasma technology. An atmospheric pressure plasma jet is used to treat UHMWPE substrates and to modify their surface chemistry. The modifications are investigated using several surface analysis techniques. The adhesion with bone cement is assessed using pull-out tests while osteoblast adhesion and proliferation is also tested making use of several cell viability assays. Additionally, the treated samples are put in simulated body fluid and the resulting calcium phosphate (CaP) deposition is evaluated as a measure of the in vitro bioactivity of the samples. The results show that the plasma modifications result in incorporation of oxygen in the surface, which leads to a significant improved adhesion to bone cement, an enhanced osteoblast proliferation and a more pronounced CaP deposition. The plasma-treated surfaces are therefore promising to act as a shoulder implant.

Complete static repopulation of decellularized porcine tissues for heart valve engineering : an in vitro study

To date, a completely in vitro repopulated tissue-engineered heart valve has not been developed. This study focused on sequentially seeding 2 cell populations onto porcine decellularized heart valve leaflets (HVL) and pericardia (PER) to obtain fully repopulated tissues. For repopulation of the interstitium, porcine valvular interstitial cells (VIC) and bone marrow-derived mesenchymal stem cells (BM-MSC) or adipose tissue-derived stem cells (ADSC) were used. In parallel, the culture medium was supplemented with ascorbic acid 2-phosphate (AA) and its effect on recolonization was investigated. Subsequently and in order to obtain an endothelial surface layer similar to those in native HVL, valvular endothelial cells (VEC) were seeded onto the scaffolds. It was shown that VIC efficiently recolonized HVL and partially also PER. On the other hand, stem cells only demonstrated limited or no subsurface cell infiltration of HVL and PER. Interestingly, the addition of AA increased the migratory capacity of both stem cell populations. However, this was more pronounced for BM-MSC, and recolonization of HVL appeared to be more efficient than that of PER tissue. VEC were demonstrated to generate a new endothelial layer on HVL and PER. However, scanning microscopy revealed that these endothelial cells were not allowed to fully spread onto PER. This study provided a proof of concept for the future generation of a bioactive tissue-engineered heart valve by showing that bioactive HVL could be generated in vitro within 14 days via complete repopulation of the interstitium with BM-MSC or VIC and subsequent generation of an entirely new endothelium.

Atmospheric Pressure Plasma Jet Treatment of Poly-ε-caprolactone Polymer Solutions To Improve Electrospinning

An atmospheric pressure plasma jet (APPJ) specifically designed for liquid treatment has been used in this work to improve the electrospinnability of a 5 w/v % solution of poly-ε-caprolactone (PCL) in a mixture of chloroform and N,N-dimethylformamide. Untreated PCL solutions were found to result in nonuniform fibers containing a large number of beads, whereas plasma-treated solutions (exposure time of 2-5 min) enabled the generation of beadless, uniform nanofibers with an average diameter of 450 nm. This enhanced electrospinnability was found to be mainly due to the highly increased conductivity of the plasma-modified PCL solutions. Consequently, more stretching of the polymer jet occurred during electrospinning, leading to the generation of bead-free fibers. Plasma treatment also results in an increased viscosity and decreased pH values. To explain these observed changes, optical emission spectroscopy (OES) has been used to examine the excited species present in the APPJ in contact with the PCL solution. This study revealed that the peaks attributed to H, CH, CH2, and C2 species could be responsible for the degradation of solvent molecules and/or PCL structures during the plasma treatment. Size exclusion chromatography and X-ray photoelectron spectroscopy results showed that the molecular weight and the chemical composition of PCL were not significantly affected by the APPJ treatment. Plasma exposure mainly results in the degradation of the solvent molecules instead of modifying the PCL macromolecules, preserving the original polymer as much as possible. A hypothesis for the observed macroscopic changes in viscosity and pH values could be the generation of new chemical species such as HCl and/or HNO3. These species are characterized by their high conductivity, low pH values, and strong polarity and could enhance the solvent quality for PCL, leading to the expansion of the polymer coil, which could in turn explain the observed enhanced viscosity after plasma modification.

Fabrication of PEOT/PBT Nanofibers by Atmospheric Pressure Plasma Jet Treatment of Electrospinning Solutions for Tissue Engineering

This study focuses on the enhanced electrospinning of 300-Polyethylene oxide-polyethylene oxide terephthalate/polybutylene terephthalate (PEOT/PBT). An atmospheric pressure plasma jet for liquid treatment is applied to a solution with 9 w/v% PEOT/PBT dissolved in either chloroform (CHCl3 ), CHCl3 xa0+xa0N,N-dimethylformamide (DMF), CHCl3 xa0+xa0methanol (MeOH), or CHCl3 xa0+xa0hexafluoroisopropanol (HFIP). For all conditions, the plasma-treated samples present better-quality fibers: less or no-beads and uniform fiber diameter distribution. Except for CHCl3 xa0+xa0DMF, no significant changes to the material bulk are detected, as shown with size exclusion chromatography (SEC). X-ray photoelectron spectroscopy (XPS) spectra performed on nanofibers record an increase in C-C bonds for the CHCl3 xa0+xa0DMF combination upon plasma modification, while a shift and slight increase in oxygen-containing bonds is found for the CHCl3 xa0+xa0HFIP and CHCl3 xa0+xa0MeOH mixtures. MTT assay shows no-cytotoxic effects for CHCl3 xa0+xa0DMF, while a better cellular adhesion is found on nanofibers from CHCl3 xa0+xa0MeOH and CHCl3 xa0+xa0HFIP. Among the examined additives, MeOH is preferable as it produces beadless electrospun nanofibers with an average diameter of 290xa0±xa0100xa0nm without causing significant changes to the final nanofiber surface properties.

Effects of a dielectric barrier discharge (DBD) treatment on chitosan/polyethylene oxide nanofibers and their cellular interactions

In this study, chitosan (CS)/polyethylene oxide (PEO) nanofibrous mats (Ø: 166u2009±u200943u2009nm) were fabricated by electrospinning and subsequently surface-modified by a dielectric barrier discharge (DBD) sustained in argon, ammonia/helium or nitrogen. The surface properties of the CS/PEO nanofibers (NFs) before and after plasma treatment were characterized using contact angle measurements, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Additionally, the mechanical properties and PEO leaching in aqueous conditions of the different NFs under study were examined by tensile tests and nuclear magnetic resonance (1H NMR) spectroscopy respectively. Finally, cell behavior and cell morphology of human foreskin fibroblasts (HFFs) on the CS/PEO NFs were evaluated via live/dead fluorescence microscopy, MTT assays and SEM. The obtained results revealed that the surface free energy of the CS/PEO NFs was significantly increased after plasma modification, which was correlated to an enrichment in surface oxygen (Ar, N2, NH3/He) and nitrogen (N2, NH3/He) functional groups. All performed plasma treatments also led to an increase in ultimate tensile strength, most likely due to an increased fiber-to-fiber friction. Additionally, it was also observed that N2 plasma treatment resulted in a decrease in PEO release, which could be attributed to more pronounced surface cross-linking. Cellular interactions on the CS/PEO NFs also significantly increased due to the performed plasma treatments. The best cellular response was noted for the Ar plasma modification although the surface hydrophilicity was the lowest in this case. These observations thus suggest that not only the wettability characteristics but also the presence of distinct functional groups on plasma-treated CS/PEO NFs have a significant influence on the observed enhanced cellular interactions.

Effects of pre- and post-electrospinning plasma treatments on electrospun PCL nanofibers to improve cell interactions

In this study, liquid plasma treatment was used to improve the morphology of Poly-є-CaproLactone (PCL) NanoFibers (NFs), followed by performing a Dielectric Barrier Discharge (DBD) plasma surface modification to enhance the hydrophilicity of electrospun mats generated from plasma-modified PCL solutions. Cell interaction studies performed after 1 day and 7 days clearly revealed the highly increased cellular interactions on the double plasma-treated nanofibers compared to the pristine ones due to the combination of (1) a better NF morphology and (2) an increased surface hydrophilicity.