Malancha Gupta

Measuring Densities of Solids and Liquids Using Magnetic Levitation: Fundamentals

This paper describes an analytical system that uses magnetic levitation to measure densities of solids and water-immiscible organic liquids with accuracies ranging from +/-0.0002 to +/-0.02 g/cm(3), depending on the type of experiment. The technique is compatible with densities of 0.8-3 g/cm(3) and is applicable to samples with volumes of 1 pL to 1 mL; the samples can be either spherical or irregular in shape. The method employs two permanent NdFeB magnets positioned with like poles facing one another--with the axis between the poles aligned with the gravitational field--and a container filled with paramagnetic medium (e.g., MnCl(2) dissolved in water) placed between these magnets. Density measurements are obtained by placing the sample into the container and measuring the position of the sample relative to the bottom magnet. The balance of magnetic and gravitational forces determines the vertical position of the sample within the device; knowing this position makes it possible to calculate the density of the sample.

Two-phase microfluidic droplet flows of ionic liquids for the synthesis of gold and silver nanoparticles.

Droplet-based microfluidic platforms have the potential to provide superior control over mixing as compared to traditional batch reactions. Ionic liquids have advantageous properties for metal nanoparticle synthesis as a result of their low interfacial tension and complexing ability; however, droplet formation of ionic liquids within microfluidic channels in a two-phase system has not yet been attained because of their complex interfacial properties and high viscosities. Here, breakup of an imidazolium-based ionic liquid into droplets in a simple two-phase system has for the first time been achieved and characterized by using a microchannel modified with a thin film fluoropolymer. This microfluidic/ionic liquid droplet system was used to produce small, spherical gold (4.28 ± 0.84 nm) and silver (3.73 ± 0.77 nm) nanoparticles.

Hybrid microcavity humidity sensor

This work presents an optical humidity sensing technique based on the combination of a whispering gallery mode microtoroidal cavity sensor and a nm-scale thick humidity-responsive polymer coating deposited via the initiated chemical vapor deposition process. As a result of the conformational change by the polymer in response to humidity, the sensitivity is increased by nearly two orders of magnitude in comparison to conventional refractometric sensing. Additionally, the dependence of the device performance on the film thickness is studied. Specifically, the thinner film enabled a faster response rate, yet a slower recovery rate, as compared to the thicker films.

Three-dimensional patterning of porous materials using vapor phase polymerization

The ability to pattern porous materials with functional polymeric coatings is important for the fabrication of next-generation microfluidic platforms, membranes, tissue scaffolds, and optical devices. Here, we demonstrate for the first time that solventless initiated chemical vapor deposition (iCVD) can be used for three-dimensional patterning of porous substrates. The individual fibers of hydrophilic chromatography paper were uniformly coated with a thin layer of hydrophobic photoresponsive poly(o-nitrobenzyl methacrylate) (PoNBMA). X-Ray photoelectron spectroscopy and contact angle measurements confirmed that the PoNBMA coating penetrated the entire depth of the paper and scanning electron microscope images confirmed that the porosity and hierarchical structure of the paper were retained during the coating process. The PoNBMA coating was then patterned through the entire depth of the paper by exposure to ultraviolet light followed by rinsing in biologically compatible buffer. We demonstrated the utility of our patterning process by fabricating three-dimensional hydrophilic and hydrophobic regions into the chromatography paper for use as paper-based microfluidic devices. Our patterning process represents an environmentally friendly method to pattern three-dimensional materials since no organic solvents are used during the polymerization process or patterning step.

Heterogeneous Films of Ionotropic Hydrogels Fabricated From Delivery Templates of Patterned Paper

The use of delivery templates makes it possible to fabricate shaped, millimeter-thick heterogeneously patterned films of ionotropic hydrogels. These structures include two-dimensional (2-D) patterns of a polymer cross-linked by different ions (e.g., alginic acid cross-linked with Ca2+ and Fe3+) and patterns of step gradients in the concentration of a single cross-linking ion. The delivery templates consist of stacked sheets of chromatography paper patterned with hydrophobic barriers (waterproof tape, transparency film, or toner deposited by a color laser printer). Each layer of paper serves as a reservoir for a different solution of cross-linking ions, while the hydrophobic barriers prevent solutions on adjacent sheets from mixing. Holes cut through the sheets expose different solutions of cross-linking ions to the surface of the templates. Films with shaped regions of hydrogels cross-linked by paramagnetic ions can be oriented with a bar magnet. Variations in the concentrations of cations used to cross-link the gel can control the mechanical properties of the film: for single alginate films composed of areas cross-linked with different concentrations of Fe3+, the regions cross-linked with high concentrations of Fe3+ are more rigid than regions cross-linked with low concentrations of Fe3+. The heterogeneous hydrogel films can be used to culture bacteria in various 2-D designs. The pattern of toxic and nontoxic ions used to cross-link the polymer determines the pattern of viable colonies of Escherichia coli within the film.

Flow invariant droplet formation for stable parallel microreactors.

The translation of batch chemistries onto continuous flow platforms requires addressing the issues of consistent fluidic behaviour, channel fouling and high-throughput processing. Droplet microfluidic technologies reduce channel fouling and provide an improved level of control over heat and mass transfer to control reaction kinetics. However, in conventional geometries, the droplet size is sensitive to changes in flow rates. Here we report a three-dimensional droplet generating device that exhibits flow invariant behaviour and is robust to fluctuations in flow rate. In addition, the droplet generator is capable of producing droplet volumes spanning four orders of magnitude. We apply this device in a parallel network to synthesize platinum nanoparticles using an ionic liquid solvent, demonstrate reproducible synthesis after recycling the ionic liquid, and double the reaction yield compared with an analogous batch synthesis.

Vapor phase deposition of functional polymers onto paper-based microfluidic devices for advanced unit operations.

Paper-based microfluidic devices have recently received significant attention as a potential platform for low-cost diagnostic assays. However, the number of advanced unit operations, such as separation of analytes and fluid manipulation, that can be applied to these devices has been limited. Here, we use a vapor phase polymerization process to sequentially deposit functional polymer coatings onto paper-based microfluidic devices to integrate multiple advanced unit operations while retaining the fibrous morphology necessary to generate capillary-driven flow. A hybrid grafting process was used to apply hydrophilic polymer coatings with a high surface concentration of ionizable groups onto the surface of the paper fibers in order to passively separate analytes, which allowed a multicomponent mixture to be separated into its anionic and cationic components. Additionally, a UV-responsive polymer was sequentially deposited to act as a responsive switch to control the path of fluid within the devices. This work extends the advanced unit operations available for paper-based microfluidics and allows for more complex diagnostics. In addition, the vapor phase polymerization process is substrate independent, and therefore, these functional coatings can be applied to other textured materials such as membranes, filters, and fabrics.

Patterned fluoropolymer barriers for containment of organic solvents within paper-based microfluidic devices.

In this study, we demonstrate for the first time the ability to pattern lipophobic fluoropolymer barriers for the incorporation of pure organic solvents as operating liquids within paper-based microfluidic devices. Our fabrication method involves replacing traditional wax barriers with fluoropolymer coatings by combining initiated chemical vapor deposition with inhibiting transition metal salt to pattern the polymer. Multiple techniques for patterning the transition metal salt are tested including painting, spray coating, and selective wetting through the use of a photoresist. The efficacy of the barrier coatings to contain organic solvents is found to be dependent on the conformality of the polymer deposited around the paper fibers. We demonstrate examples of the benefits provided by the containment of organic solvents in paper-based microfluidic applications including the ability to tune the separation of analytes by varying the operating solvent and by modifying the channel region of the devices with additional polymer coatings. The work exhibited in this paper has the potential to significantly expand the applications of paper-based microfluidics to include detection of water insoluble analytes. Additionally, the generality of the patterning process allows this technique to be extended to other applications that may require the use of patterned hydrophobic and lipophobic regions, such as biosensing, chemical detection, and optics.

Patterning precipitates of reactions in paper

This article describes a method for patterning certain solids—insoluble salts and reduced metals—in sheets of paper. Chemical reactions that produce these solids as precipitates occur when a stamp of patterned paper inked with an aqueous solution of reagent comes into contact with a paper substrate containing a second reagent. The pattern is determined by a hydrophobic barrier on the stamp that restricts delivery of the ink in two dimensions. The technique is one of the few methods available to generate two-dimensional patterns of solids within the bulk of sheets of paper. It can reliably produce features with lateral dimensions only down to 1 mm, but is convenient, inexpensive, and amenable to use in large-area patterning. The method can be used to introduce function to paper-based systems: (i) paramagnetic salts precipitated within paper allow pieces of it to be manipulated or separated from mixtures with a bar magnet, (ii) the precipitation of transition metals or enzymes can be used to position and store catalysts on paper for subsequent use, (iii) catalysts patterned in two dimensions in paper can be used to generate dynamic 3-D structures when exposed to appropriate substrates: for example, a ring of Pd0 deposited on a sheet of paper will generate a cylindrical “cage” of rising oxygen bubbles when exposed to an aqueous solution of hydrogen peroxide, and (iv) patterns of catalysts or colored precipitates can serve as deterrents to counterfeiting.

Directed deposition of functional polymers onto porous substrates using metal salt inhibitors.

This paper demonstrates the ability to control the location of polymer deposition onto porous substrates using vapor phase polymerization in combination with metal salt inhibitors. Functional polymers such as hydrophobic poly(1H,1H,2H,2H-perfluorodecyl acrylate), click-active poly(pentafluorophenyl methacrylate), and light-responsive poly(ortho-nitrobenzyl methacrylate) were patterned onto porous hydrophilic substrates using metal salts. A combinatorial screening approach was used to determine the effects of different transition metal salts and reaction parameters on the patterning process. It was found that CuCl(2) and Cu(NO(3))(2) were effective at uniformly inhibiting the deposition of all three polymers through the depth of the porous substrate and along the entire cross section. This study offers a new and convenient method to selectively deposit a wide variety of functional polymers onto porous materials and will enable the production of next-generation multifunctional paper-based microfluidic devices, polymeric photonic crystals, and filtration membranes.