Marcos R. V. Lanza

Electrochemical sensor highly selective for estradiol valerate determination based on a modified carbon paste with iron tetrapyridinoporphyrazine

This work reports the use of iron tetrapyridinoporphyrazine (FeTPyPz) as a highly selective catalyst in the construction of an electrochemical sensor for estradiol valerate (EV) determination. The sensor was prepared by modifying a carbon paste with FeTPyPz. The best results were obtained in a mixture of acetonitrile (MeCN) and 0.1 mol L(-1) phosphate buffer solution (pH 6.0) in a volume ratio of 47 : 53. A linear response range was observed between 45 and 450 micromol L(-1) with a sensitivity of 12160 +/- 306 microA L mol(-1) and quantification and detection limits of 45 and 13 micromol L(-1), respectively. The repeatability, expressed as the relative standard deviation (RSD) for n = 10, was 5.9% ([EV] = 50 micromol L(-1)). The reproducibility (RSD) for the sensor construction was better than 4% and the operational stability (RSD) over 50 measurements was 1.8%. A detailed investigation regarding the selectivity and electrochemical characteristics was carried out. Finally, in a first step to evaluate the application potential of the sensor, it was successfully applied to determine EV in a commercial formulation.

Construction and application of an electrochemical sensor for paracetamol determination based on iron tetrapyridinoporphyrazine as a biomimetic catalyst of P450 enzyme

This work describes the construction and application of a biomimetic sensor for paracetamol determination in different samples . The sensor was prepared by modifying a glassy carbon electrode surface with a Nafion® membrane doped with FeTPyPz. The best performance of the sensor in 0.1 mol L-1 acetate buffer was at pH 3.6. Under these conditions, an oxidation potential of paracetamol was observed at 445 mV vs. Ag|AgCl. The sensor presented a linear response range between 4.0 and 420 µmol L-1, a sensitivity of 46.015 mA L mol-1 cm-2, quantification and detection limits of 4.0 µmol L-1 and 1.2 µmol L-1, respectively. A detailed investigation about its electrochemical behavior and selectivity was carried out. The results suggested that FeTPyPz presents catalytic properties similar to P450 enzyme for paracetamol oxidation. Finally, the sensor was applied for paracetamol determination in commercial drugs and for the monitoring of its degradation in an electrochemical batch reactor effluent.

Avaliação da degradação do diclofenaco sódico utilizando H2O2/fenton em reator eletroquímico

This paper describes a degradation study of the anti-inflammatory sodium diclofenac in aqueous medium using an electro-chemical flow reactor with a gas diffusion electrode as cathode. Two degradation processes were compared: by H2O2 electro-generated and H2O2 electro-generated/Fe(II). Concentration of sodium diclofenac was determined during the experiments by HPLC. The changes in chemical oxigen demand (COD) were also evaluated. Under the specific reaction conditions, 350 mg L-1 of H2O2 was electro-generated and 99.2% of sodium diclofenac was degradated, with 27.4% COD reduction. At the same conditions, but using Fe(II), drug degradation was 99.4% and the COD reduction was 63.2%.

Estudo da degradação de ranitidina via H2O2 eletrogerado/Fenton em um reator eletroquímico com eletrodos de difusão gasosa

The study of the electrochemical degradation of the ranitidine was developed using an electrochemical reactor with a gas diffusion electrode (GDE) as cathode. The electrolysis experiments was performed at constant current (1 4 A. The process reached a production of 630 mg L-1 of the H2O2 at 7 A. The ranitidine concentrations was reduced in 99.9% (HPLC) and chemical oxygen demand (COD) was reduced in 86.7% by electro-Fenton.

Development and Application of a Highly Selective Biomimetic Sensor for Detection of Captopril, an Important Ally in Hypertension Control

A biomimetic sensor is proposed as a promising new analytical method for determination of captopril in different classes of samples. The sensor was prepared by modifying a carbon paste electrode with iron (II) phthalocyanine bis(pyridine) [FePc(dipy)] complex. Amperometric measurements in a batch analytical mode were first carried out in order to optimize the sensor response. An applied potential lower than 0.2 V vs Ag|AgCl in 0.1 mol L-1 of TRIS buffer at pH 8.0 provided the best response, with a linear range of 2.5 x 10-5 to 1.7 x 10-4 mol L-1. A detailed investigation of the selectivity of the sensor, employing seventeen other drugs, was also performed. Recovery studies were carried out using biological and environment samples in order to evaluate the sensors potential for use with these sample classes. Finally, the performance of the biomimetic sensor was optimized in a flow injection (FIA) system using a wall jet electrochemical cell. Under optimized flow conditions, a broad linear response range, from 5.0 x 10-4 to 2.5 x 10-2 mol L-1, was obtained for captopril, with a sensitivity of 210 ± 1 μA L mol-1.

Development of biomimetic sensor for fast and sensitive detection of Norfloxacin

A biomimetic sensor is proposed as a promising new analytical method for determination of norfloxacin (NF) in pharmaceuticals. The sensor was prepared by modifying a glassy carbon electrode surface with a Nafion ® membrane doped with poly(copper phthalocyanine) complex (poly-CuPc). Amperometric measurements carried out with the sensor under an applied potential of -0.05 V vs Ag|AgCl in 0.1 mol L -1 acetic acid containing 1.5 � 10 -3 mol L -1 hydrogen peroxide showed a linear response range from 2.0 � 10 -4 to 1.2 � 10 -3 mol L -1 . Selectivity and interference studies were also performed. A sensor response mechanism is proposed, based on the experimental evidence. Recovery studies were carried out using environmental samples, in order to evaluate the sensors potential for use with these sample classes. Finally, sensor performance was evaluated using analyses of commercial formulations.

Selective UV-filter detection with sensors based on stainless steel electrodes modified with polyaniline doped with metal tetrasulfonated phthalocyanine films

This work describes the construction and application of two amperometric sensors for sensitive UV-filter determination. The sensors were prepared using stainless steel electrodes in which polyaniline (PANI) was electrochemically polymerized in the presence of nickel (NiPcTS) or iron (FePcTS) tetrasulfonated phthalocyanines. The sensor surface characterizations were carried out using atomic force microscopy (AFM). The PANI/NiPcTS sensor was selective for the chemical UV-filter p-aminobenzoic acid (PABA) and the PANI/FePcTS sensor was selective for octyldimethyl-PABA (ODP), both in a mixture of tetrahydrofuran (THF) and 0.1 mol L(-1) H2SO4 at a volume ratio of 30 : 70, and with an applied potential of 0.0 mV vs. Ag|AgCl. A detailed investigation of the selectivity was carried out for both sensors, in order to determine their responses for ten different UV filters. Finally, each sensor was successfully applied to PABA or ODP quantification in sunscreen formulations and water from swimming pools.

Aplicação e avanços da espectroscopia de luminescência em análises farmacêuticas

This paper provides a review on the latest advances and applications of the luminescence spectroscopy for the development of pharmaceuticals analyses methods, basically based on the photo- and chemiluminescence. The different forms of the drugs determination on pharmaceuticals through the fluorescence and chemiluminescence are discussed. The analyses include the drugs native fluorescence (liquid and solid-phases); the fluorescence from the oxidizing or reducing forms of the drug; the fluorescence from the chemical derivatization and their photochemistry and hydrolysis reactions. The quenching of luminescence and chemiluminescence generation for the pharmaceutical quantification are also shown. Finally, the trends and future perspectives of the luminescence spectroscopy in the field of the pharmaceutical research are discussed.

Online Monitoring of Electrochemical Degradation of Paracetamol through a Biomimetic Sensor

This paper reports, for the first time, the online monitoring to the electrochemical degradation of the paracetamol using a biomimetic sensor coupled to a Flow Injection Analysis (FIA) system. The electrochemical degradation of the drug was carried out in aqueous medium using a flow-by reactor with a DSA anode. The process efficiency was monitored at real time by the biomimetic sensor constructed by modifying a glassy carbon electrode with a Nafion membrane doped with iron tetrapyridinoporphyrazine (FeTPyPz). Simultaneously, we carried out off-line analysis by liquid chromatography (HPLC) during the experiments in order to validate the proposed system. In addition, to investigate the degradation products of the paracetamol electrolysis, we used the techniques of UPLC/MS and GC/MS.

Degradação eletroquímica do cloranfenicol em reator de fluxo

This paper reports a study of electrochemical degradation of the chloramphenicol antibiotic in aqueous medium using a flow-by reactor with DSA® anode. The process efficiency was monitored by chloramphenicol concentration analysis with liquid chromatography (HPLC) during the experiments. Analysis of Total Organic Carbon (TOC) was performed to estimate the degradation degree and Ion Chromatography (IC) was performed to determinate inorganic ions formed during the eletrochemical degradation process. In electrochemical flow-by reactor, 52% of chloramphenicol was degraded, with 12% TOC reduction. IC analysis showed the production of chloride ions (25 mg L-1), nitrate ions (6 mg L-1) and nitrite ions (4.5 mg L-1).