Marica Markovic

Enzymatic synthesis of hyaluronic acid vinyl esters for two-photon microfabrication of biocompatible and biodegradable hydrogel constructs

Two-photon polymerization (2PP) allows 3D microfabrication of biomaterial scaffolds with user-defined geometry. This technique is highly promising for 3D cell culture and tissue engineering. However, biological applications of 2PP require photopolymerizable hydrogels with high reactivity and low cytotoxicity. This paper describes a novel hydrogel system based on hyaluronic acid vinyl esters (HA-VE), which enabled fast 2PP-fabrication of 3D hydrogel constructs with μm-scale accuracy. A series of HA-VE macromers with tunable degrees of substitution were synthesized by lipase-catalyzed transesterification. HA-VE gels were proved to be injectable, photocurable, enzymatically degradable and mechanically comparable to various soft tissues. Owing to the unique molecular design, degradation products of HA-VE gels through hydrolysis are non-toxic polyvinyl alcohol and adipic acid. Furthermore, HA-VE gels were systematically characterized and compared to HA-acrylates (HA-AC) and HA-methacrylates (HA-MA) gels including macromer cytotoxicity, photoreactivity, swelling, and gel stiffness. Cytotoxicity assay with L929 fibroblasts revealed that HA-VE was significantly less toxic than HA-AC (P < 0.01) and HA-MA (P < 0.05). Crosslinking efficiency of HA-VE was comparable to HA-AC and much higher than HA-MA. Although the reactivity of HA-VE for homopolymerization was insufficient for 2PP, it was demonstrated that thiol–ene chemistry could substantially improve its reactivity. This optimization led to 2PP-fabrication of a HA-VE hydrogel construct with μm-scale accuracy. Low cytotoxicity, high reactivity and good biodegradability makes HA-VE promising candidates for biological applications in cell culture and tissue engineering.

Hybrid Tissue Engineering Scaffolds by Combination of Three-Dimensional Printing and Cell Photoencapsulation

Three-dimensional (3D) printing offers versatile possibilities for adapting the structural parameters of tissue engineering scaffolds. However, it is also essential to develop procedures allowing efficient cell seeding independent of scaffold geometry and pore size. The aim of this study was to establish a method for seeding the scaffolds using photopolymerizable cell-laden hydrogels. The latter facilitates convenient preparation, and handling of cell suspension, while distributing the hydrogel precursor throughout the pores, before it is cross-linked with light. In addition, encapsulation of living cells within hydrogels can produce constructs with high initial cell loading and intimate cell-matrix contact, similar to that of the natural extra-cellular matrix (ECM). Three dimensional scaffolds were produced from poly(lactic) acid (PLA) by means of fused deposition modeling. A solution of methacrylamide-modified gelatin (Gel-MOD) in cell culture medium containing photoinitiator Li-TPO-L was used as a hydrogel precursor. Being an enzymatically degradable derivative of natural collagen, gelatin-based matrices are biomimetic and potentially support the process of cell-induced remodeling. Preosteoblast cells MC3T3-E1 at a density of 10 × 106 cells per 1 mL were used for testing the seeding procedure and cell proliferation studies. Obtained results indicate that produced constructs support cell survival and proliferation over extended duration of our experiment. The established two-step approach for scaffold seeding with the cells is simple, rapid, and is shown to be highly reproducible. Furthermore, it enables precise control of the initial cell density, while yielding their uniform distribution throughout the scaffold. Such hybrid tissue engineering constructs merge the advantages of rigid 3D printed constructs with the soft hydrogel matrix, potentially mimicking the process of ECM remodeling.

Cross-Linkable Gelatins with Superior Mechanical Properties Through Carboxylic Acid Modification: Increasing the Two-Photon Polymerization Potential

The present work reports on the development of photo-cross-linkable gelatins sufficiently versatile to overcome current biopolymer two-photon polymerization (2PP) processing limitations. To this end, both the primary amines as well as the carboxylic acids of gelatin type B were functionalized with photo-cross-linkable moieties (up to 1 mmol/g) resulting in superior and tunable mechanical properties (G′ from 5000 to 147000 Pa) enabling efficient 2PP processing. The materials were characterized in depth prior to and after photoinduced cross-linking using fully functionalized gelatin-methacrylamide (gel-MOD) as a benchmark to assess the effect of functionalization on the protein properties, cross-linking efficiency, and mechanical properties. In addition, preliminary experiments on hydrogel films indicated excellent in vitro biocompatibility (close to 100% viability) both in the presence of MC3T3 preosteoblasts and L929 fibroblasts. Moreover, 2PP processing of the novel derivative was superior in terms of applied laser power (≥40 vs ≥60 mW for gel-MOD at 100 mm/s) as well as post-production swelling (0–20% vs 75–100% for gel-MOD) compared to those of gel-MOD. The reported novel gelatin derivative (gel-MOD-AEMA) proves to be extremely suitable for direct laser writing as both superior mimicry of the applied computer-aided design (CAD) was obtained while maintaining the desired cellular interactivity of the biopolymer. It can be anticipated that the present work will also be applicable to alternative biopolymers mimicking the extracellular environment such as collagen, elastin, and glycosaminoglycans, thereby expanding current material-related processing limitations in the tissue engineering field.

Calibration of colloidal probes with atomic force microscopy for micromechanical assessment

Mechanical assessment of biological materials and tissue-engineered scaffolds is increasingly focusing at lower length scale levels. Amongst other techniques, atomic force microscopy (AFM) has gained popularity as an instrument to interrogate material properties, such as the indentation modulus, at the microscale via cantilever-based indentation tests equipped with colloidal probes. Current analysis approaches of the indentation modulus from such tests require the size and shape of the colloidal probe as well as the spring constant of the cantilever. To make this technique reproducible, there still exist the challenge of proper calibration and validation of such mechanical assessment. Here, we present a method to (a) fabricate and characterize cantilevers with colloidal probes and (b) provide a guide for estimating the spring constant and the sphere diameter that should be used for a given sample to achieve the highest possible measurement sensitivity. We validated our method by testing agarose samples with indentation moduli ranging over three orders of magnitude via AFM and compared these results with bulk compression tests. Our results show that quantitative measurements of indentation modulus is achieved over three orders of magnitude ranging from 1 kPa to 1000 kPa via AFM cantilever-based microindentation experiments. Therefore, our approach could be used for quantitative micromechanical measurements without the need to perform further validation via bulk compression experiments.

Acylstannanes: Cleavable and Highly Reactive Photoinitiators for Radical Photopolymerization at Wavelengths above 500 nm with Excellent Photobleaching Behavior

Within this work, a novel acylstannane-based photoinitiator (PI) is presented. Tetrakis(2,4,6-trimethylbenzoyl)stannane (1) displays outstanding properties compared to state-of-the-art acylgermane-based initiators. Most importantly, the initiator shows absorption up to 550 nm, which allows higher penetration depths, especially in highly filled photopolymers. Besides that, 1 shows extremely high photoinitiating activity towards (meth)acrylic double bonds, as well as very fast photobleaching. Furthermore, unlike many organotin compounds, 1 shows surprisingly low cytotoxicity.