Mariko Hattori

A new simple evaluation method of the monosyllable /sa/ using a psychoacoustic system in maxillectomy patients

PURPOSE An objective assessment of speech would benefit the prosthetic rehabilitation of maxillectomy patients. This study aimed to establish a simple, objective evaluation of monosyllable /sa/ utterances in maxillectomy patients by using a psychoacoustic system typically used in industry. MATERIALS AND METHODS This study comprised two experiments. Experiment 1 involved analysis of the psychoacoustic parameters (loudness, sharpness and roughness) in monosyllable /sa/ utterances by 18 healthy subjects (9 males, 9 females). The utterances were recorded in a sound-treated room. The coefficient of variation (CV) for each parameter was compared to identify the most suitable parameter for objective evaluation of speech. Experiment 2 involved analysis of /sa/ utterances by 18 maxillectomy patients (9 males, 9 females) with and without prosthesis, and comparisons of the psychoacoustic data between the healthy subjects and maxillectomy patients without prosthesis, between the maxillectomy patients with and without prosthesis, and between the healthy subjects and maxillectomy patients with prosthesis. RESULTS The CV for sharpness was the lowest among the three psychoacoustic parameters in both the healthy males and females. There were significant differences in the sharpness of /sa/ between the healthy subjects and the maxillectomy patients without prosthesis (but not with prosthesis), and between the maxillectomy patients with and without prosthesis. CONCLUSION We found that the psychoacoustic parameters typically adopted in industrial research could also be applied to evaluate the psychoacoustics of the monosyllable /sa/ utterance, and distinguished the monosyllable /sa/ in maxillectomy patients with an obturator from that without an obturator using the system.

Evaluation of articulation simulation system using artificial maxillectomy models.

Acoustic evaluation is valuable for guiding the treatment of maxillofacial defects and determining the effectiveness of rehabilitation with an obturator prosthesis. Model simulations are important in terms of pre-surgical planning and pre- and post-operative speech function. This study aimed to evaluate the acoustic characteristics of voice generated by an articulation simulation system using a vocal tract model with or without artificial maxillectomy defects. More specifically, we aimed to establish a speech simulation system for maxillectomy defect models that both surgeons and maxillofacial prosthodontists can use in guiding treatment planning. Artificially simulated maxillectomy defects were prepared according to Aramanys classification (Classes I-VI) in a three-dimensional vocal tract plaster model of a subject uttering the vowel /a/. Formant and nasalance acoustic data were analysed using Computerized Speech Lab and the Nasometer, respectively. Formants and nasalance of simulated /a/ sounds were successfully detected and analysed. Values of Formants 1 and 2 for the non-defect model were 675.43 and 976.64 Hz, respectively. Median values of Formants 1 and 2 for the defect models were 634.36 and 1026.84 Hz, respectively. Nasalance was 11% in the non-defect model, whereas median nasalance was 28% in the defect models. The results suggest that an articulation simulation system can be used to help surgeons and maxillofacial prosthodontists to plan post-surgical defects that will be facilitate maxillofacial rehabilitation.

Measurement of Voice Onset Time in Maxillectomy Patients

Objective speech evaluation using acoustic measurement is needed for the proper rehabilitation of maxillectomy patients. For digital evaluation of consonants, measurement of voice onset time is one option. However, voice onset time has not been measured in maxillectomy patients as their consonant sound spectra exhibit unique characteristics that make the measurement of voice onset time challenging. In this study, we established criteria for measuring voice onset time in maxillectomy patients for objective speech evaluation. We examined voice onset time for /ka/ and /ta/ in 13 maxillectomy patients by calculating the number of valid measurements of voice onset time out of three trials for each syllable. Wilcoxons signed rank test showed that voice onset time measurements were more successful for /ka/ and /ta/ when a prosthesis was used (Z = −2.232, P = 0.026 and Z = −2.401, P = 0.016, resp.) than when a prosthesis was not used. These results indicate a prosthesis affected voice onset measurement in these patients. Although more research in this area is needed, measurement of voice onset time has the potential to be used to evaluate consonant production in maxillectomy patients wearing a prosthesis.

Effect of Experimental Palatal Prosthesis on Voice Onset Time.

PURPOSE Objective evaluation of a patients speech is needed in prosthetic dentistry because the prostheses can affect the intelligibility of speech. Measurement of voice onset time is one evaluation method of consonant production used in phonetic science. The purpose of this study was to confirm the influence of a palatal prosthesis on consonant production by measuring voice onset time. MATERIALS AND METHODS In this study, voice onset time was measured in 10 healthy women (mean age 26.5 years) under two conditions: with and without an experimental palatal prosthesis. In this study, voice onset time of /ta/ and /ka/ were used to determine the effect of wearing a palatal prosthesis; /pa/ was tested as a control, with the null hypothesis that voice onset time of /ta/ and /ka/ would not change when wearing a palatal prosthesis. RESULTS Medial voice onset time of /pa/, /ta/, and /ka/ syllables without the palatal prosthesis was 22.5 ms, 19.5 ms, and 42.5 ms, whereas that with the palatal prosthesis was 22.5 ms, 23.5 ms, and 55.0 ms. Voice onset times for /ta/ and /ka/ were prolonged when wearing the experimental palatal prosthesis, whereas /pa/ showed no significant difference. CONCLUSION Consonant production was affected by wearing a palatal prosthesis, and this change in sound was detected by measuring voice onset time.

The Role of Portable Documentation Format in Three-Dimensional Interactive Visualization in Maxillofacial Prosthetics

Although digital technology has advanced the visualization of treatment planning and rehabilitation in prosthodontics, the field of maxillofacial prosthetics is in vital need of an accessible document for exchange of interactive three-dimensional (3D) model visualization without requiring installation of any additional software. This article introduces a 3D data documentation method for effective interactive digital visualization in maxillofacial prosthetics using a portable documentation format (PDF).

Orientation of handle for successful prosthetic treatment in patients with an anatomic compromise after a maxillectomy

This clinical technique provides a key procedure for successful prosthetic treatment in patients with an anatomical compromise after a maxillectomy. When making a preliminary impression, the clinician must keep the handle of the stock tray parallel to the patients interpupillary line extraorally to maintain the correct position of the tray and to make a record of the inclination of the occlusal plane. This simple consideration during this first step of making a preliminary impression can be an important guide for both dentists and dental technicians. Information about the correct positioning of the tray and the inclination of the occlusal plane obtained by using a stock tray handle will greatly reduce the stress experienced by dentists, dental technicians, and patients during the fabrication of the prosthesis and will ultimately lead to successful prosthetic treatment in patients with anatomic compromise resulting from a maxillectomy.

The Role of Digitization in the Rapid Reproduction of an Obturator in a Frail Elderly Patient.

This case report describes the reproduction of the current obturator of a frail elderly patient using the digitization concept. A computed tomography scanner was used to scan the obturator. The virtual model was created using three-dimensional modeling software. The model was printed using a plastic with a low melting point with a fused deposition modeling technique in a three-dimensional printer and then conventionally processed. The definitive obturator was inserted and evaluated for fit, function, and esthetics and was successfully delivered at the second visit. The patient was satisfied with the oral function and esthetics of the reproduced obturator. This case report confirms the effectiveness of digitization in the reproduction of an obturator that enabled satisfactory oral function and esthetics.

Preschool and School Phases of Postmaxillectomy Prosthetic Rehabilitation in a Child: A Clinical Report

This report describes the postmaxillectomy prosthetic rehabilitation of a child with maxillary chondrosarcoma over an 8-year period. Specifically, it (1) describes the planning and rehabilitation procedures carried out during the period from before the operation to the time when the patient started elementary school and (2) reports the results of evaluations of the patients oral and psychosocial function conducted during the school phase. The prosthetic treatment plan was separated into two phases (the preschool and school phases) and was started prior to surgery, when an immediate surgical obturator was designed by the surgeons. After the operation, it was considered important to provide the patient and her mother with training regarding how the defect should be cleaned, trismus prevention, and how the prosthesis should be fitted. In addition, esthetic improvements and the ability to speak clearly were also targeted during treatment planning. After surgery, obturators were fabricated in a conventional manner and fitted at the ages of 2, 4, 6, 8, and 10 years. The patients oral function during the use of the obturators was evaluated objectively. Marked improvements in oral function were seen during both treatment phases. The patients ability to perform psychosocial functions at school also improved during the use of the obturators.

Feasibility and Accuracy of Noncontact Three-Dimensional Digitizers for Geometric Facial Defects: An In Vitro Comparison

PURPOSE To evaluate the feasibility and accuracy of noncontact three-dimensional (3D) digitization systems for capturing facial defects. MATERIALS AND METHODS A stone model of a facial defect was digitized using high-accuracy industrial computed tomography as a reference scan. The model was also scanned using four different types of noncontact 3D digitizers: a laser beam light-sectioning technology with camera system and three different stereophotogrammetry systems. All 3D images were reconstructed with corresponding software and saved as standard triangulated language (STL) files. The 3D datasets were geometrically evaluated and compared to the reference data using 3D evaluation software. Kruskal-Wallis H tests were performed to assess differences in absolute 3D deviations between scans, with statistical significance defined as P < .05. RESULTS The four noncontact 3D digitization systems were feasible for digitizing the facial defect model, although the median 3D deviation of the four digitizers varied. There was a significant difference in accuracy among the digitizers (P < .001). CONCLUSION Digitization of facial defect models using various noncontact 3D digitizers appears to be feasible and is most accurate with laser beam light-sectioning technology. Further investigations assessing digitization of facial defects among patients are required to clinically verify the results of this study.

Geometric Evaluation of the Effect of Prosthetic Rehabilitation on Facial Asymmetry in Patients with Unilateral Maxillectomy

PURPOSE This study aimed (1) to geometrically evaluate areas of facial asymmetry in patients with two different types of maxillectomy defect compared to a control group, (2) to geometrically evaluate the effect of an obturator prosthesis on facial asymmetry, and (3) to investigate the correlation between three-dimensional (3D) deviation values and number of missing teeth. MATERIALS AND METHODS Facial data from 13 normal control participants and 26 participants with two types of maxillectomy defect (groups 1 and 2) were acquired with a noncontact 3D digitizer. Facial asymmetry was evaluated by superimposing a facial scan onto its mirror scan using 3D evaluation software. Facial scans with and without obturator prostheses were also superimposed to evaluate the obturator effect. The correlation between 3D deviation values and number of missing teeth was also evaluated. Statistical analyses were performed. RESULTS Facial asymmetry was significantly different between the control group and each maxillectomy defect group (group 1: P < .0001 and P = .020 without and with obturator, respectively; group 2: P < .0001 for both conditions). There were no significant differences in asymmetry between groups 1 and 2 either without or with obturator (P = .457 and P = .980, respectively). There was a significant difference in the obturator effect between groups 1 and 2 (P = .038). 3D deviation values were positively correlated with number of missing teeth in group 1 (r = 0.594, P = .032), but not in group 2. CONCLUSION A noncontact 3D digitizer and 3D deviation assessment were effective for analyzing facial data of maxillectomy patients. Obturators were effective for improving facial deformities in these patients.