Mark Kearns

Banana and Abaca Fiber-Reinforced Plastic Composites Obtained by Rotational Molding Process

Natural fibers can be used in rotational molding process to obtain parts with improved mechanical properties. Different approaches have been followed in order to produce formulations containing banana or abaca fiber at 5% weight, in two- and three-layer constructions. Chemically treated abaca fiber has also been studied, causing some problems in processability. Fibers used have been characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), optical microscopy, and single-fiber mechanical tests. Rotomolded parts have been tested for tensile, flexural, and impact properties, demonstrating that important increases in elastic modulus are achieved with these fibers, although impact properties are reduced.

Study of Adhesion Between Two Layers in Multilayer Rotomolded Products

Manufacturing multilayer objects by rotomolding is a new technology, which is expected to have several industrial applications in future. For multilayer objects it is important to know whether the layers are adequately welded. This communication describes the characterization of the interface between two polymeric layers, grafted polyethylene and poly(ethylene vinyl alcohol), which were thermally welded during rotomolding.

The Rotational Molding Characteristics of Metallocene Polyethylene Skin/Foam Structures

This article reports on the results of ongoing work in which the foaming characteristics of metallocene-catalyzed linear low density polyethylenes for rotational molding are investigated. Earlier publications related rheological and thermal parameters to the polymer structure and mechanical properties and found that metallocene polyethylene can be used in rotational foam molding to produce a foam that will perform as well as a Ziegler-Natta catalyzed foam. Through adjustments to molding conditions, the significant processing and physical material parameters, which optimize metallocene catalyzed linear low-density polyethylene foam structure, have been identified. This article details the optimum processing route for the production of two layer skin/foam parts using the drop box method.

Rapid prototyping applied to a new development in moulds for rotational moulding

The aim of this work has been to adapt and apply the advantages of rapid prototyping and electroforming technologies to try to achieve an innovative mould design for rotational moulding. The new innovative design integrates an electroformed shell, manufactured starting from a rapid prototyping mandrel, with different designed standard aluminium tools. The shell holder enables mould assembly with high precision manufacture of a shell in a few minutes. The overall mould cost is significantly decreased because it is only necessary to manufacture one or two shells each time; however, the rest of the elements of the mould are standard and usable for an infinite number of shells, depending on size.

Recycling of polymeric fraction of cable waste by rotational moulding

This study focuses on the mechanical recycling of polymeric waste that is produced in considerable amount from the cable industry. Every year large amounts of cables become waste; wires recycling has traditionally focused on metal recovery, while the polymer cover has just been considered as a residue, being landfilled or incinerated. Nowadays, increasingly restrictive regulations and concern about environment make necessary to reduce landfilling as much as possible. Main novelty of the study is that the material used in the research is a post-consumer material and the entire residual material is used, without a previous purification, in contrast with similar studies. Characterization of this residue was performed by thermal analysis, showing that the material is mainly made up of a heavy fraction (84% of the residue), which is not able to melt, fact what makes recycling more difficult. Once characterized, the material was ground, blended with virgin polyethylene and reprocessed by rotational moulding. The influence of the amount of residue and parts structure (1, 2 and 3 layers) was assessed, studying the mechanical behaviour of obtained parts (tensile, flexural and impact properties). It has been found that although mechanical properties get reduced with the increased amount of residue, up to a 35% of residue can be used without an important decrease in mechanical properties. On the other hand, the use of multiple layers in the mouldings allowed obtaining a better external appearance without compromising the mechanical properties.

An innovative electroforming process for oil heated rotational moulding tools

Rotational moulding is a method to produce hollow plastic articles. Heating is normally carried out by placing the mould into a hot air oven where the plastic material in the mould is heated. The most common cooling media are water and forced air. Due to the inefficient nature of conventional hot air ovens most of the energy supplied by the oven does not go to heat the plastic and as a consequence the procedure has very long cycle times. Direct oil heating is an effective alternative in order to achieve better energy efficiency and cycle times. This research work has combined this technology with new innovative design of mould, applying the advantages of electroforming and rapid prototyping. Complex cavity geometries are manufactured by electroforming from a rapid prototyping mandrel. The approach involves conformal heating and cooling channels, where the oil flows into a parallel channel to the electroformed cavity (nickel or copper). Because of this the mould enables high temperature uniformity with direct heating and cooling of the electroformed shell. Uniform heating and cooling is important not only for good quality parts but also for good uniform wall thickness distribution in the rotationally moulded part. The experimental work with the manufactured prototype mould has enabled analysis of the thermal uniformity in the cavity, under different temperatures.Copyright

Investigation of the processing characteristics and mechanical properties of metallocene-catalysed polyethylene foams for rotational moulding

The object of this work is to investigate the foaming characteristics of three grades of metallocene-catalysed linear low-density polyethylenes for rotational moulding using both an exothermic and endothermic chemical blowing agent. This paper reports on the results of ongoing experimental investigations in which rheological and thermal parameters are related to the polymer structure and mechanical properties. Through adjustments to moulding conditions, the significant processing and physical material parameters, which optimise metallocene-catalysed linear low-density polyethylene foam structure, have been identified. The results obtained from equivalent conventional grades of Ziegler-Natta-catalysed linear low-density polyethylene are used as a basis for comparison.

The effect of internal mould water spray cooling on rotationally moulded polyethylene parts

The conventional method of cooling during the rotational moulding process is through the use of forced air. During the cooling phase of a typical rotomoulding cycle, large volumes of high velocity room temperature air are forced across the outside of the rotating rotomoulding tool to encourage cooling of the metal mould and molten polymer. Since no cooling is applied to the inside of the mould, the inner surface of the polymer (polyethylene) cools more slowly and will have a tendency to be more crystalline and the polyethylene will have a higher density in this region. The side that cools more quickly (in contact with the inside mould wall) will be less crystalline, and will therefore have a lower density. The major consequence of this difference in crystallinity will be a buildup of internal stresses producing warpage and excessive shrinkage of the part with subsequent increased levels of scrap. Therefore excessive cooling on the outside of the mould should be avoided. One consequence of this effect is t...

Multilayered glass fibre-reinforced composites in rotational moulding

The potential of multiple layer fibre‐reinforced mouldings is of growing interest to the rotational moulding industry because of their cost/performance ratio. The particular problem that arises when using reinforcements in this process relate to the fact that the process is low shear and good mixing of resin and reinforcement is not optimum under those conditions. There is also a problem of the larger/heavier reinforcing agents segregating out of the powder to lay up on the inner part surface. In this study, short glass fibres were incorporated and distributed into a polymer matrix to produce fibre‐reinforced polymer composites using the rotational moulding process and characterised in terms of morphology and mechanical properties.