Maryse Maugey

Engineering hybrid nanotube wires for high-power biofuel cells

Poor electron transfer and slow mass transport of substrates are significant rate-limiting steps in electrochemical systems. It is especially true in biological media, in which the concentrations and diffusion coefficients of substrates are low, hindering the development of power systems for miniaturized biomedical devices. In this study, we show that the newly engineered porous microwires comprised of assembled and oriented carbon nanotubes (CNTs) overcome the limitations of small dimensions and large specific surface area. Their improved performances are shown by comparing the electroreduction of oxygen to water in saline buffer on carbon and CNT fibres. Under air, and after several hours of operation, we show that CNT microwires exhibit more than tenfold higher performances than conventional carbon fibres. Consequently, under physiological conditions, the maximum power density of a miniature membraneless glucose/oxygen CNT biofuel cell exceeds by far the power density obtained for the current state of art carbon fibre biofuel cells.

Shape and Temperature Memory of Nanocomposites with Broadened Glass Transition

Shape-memory polymers can revert to their original shape when they are reheated. The stress generated by shape recovery is a growing function of the energy absorbed during deformation at a high temperature; thus, high energy to failure is a necessary condition for strong shape-memory materials. We report on the properties of composite nanotube fibers that exhibit this particular feature. We observed that these composites can generate a stress upon shape recovery up to two orders of magnitude greater than that generated by conventional polymers. In addition, the nanoparticles induce a broadening of the glass transition and a temperature memory with a peak of recovery stress at the temperature of their initial deformation.

Anisotropic Thin Films of Single-Wall Carbon Nanotubes from Aligned Lyotropic Nematic Suspensions

Lyotropic nematic aqueous suspensions of single-wall carbon nanotubes can be uniformly aligned in thin cells by shearing. Homogeneous anisotropic thin films of nanotubes can be prepared by drying the nematic. Optical transmission between parallel or crossed polarizers is measured and described in order to estimate the dichroic ratio. The order parameter is measured using polarized Raman spectroscopy and found to be quite weak due to entanglement of the nanotubes and/or to an intrinsic viscoelastic behavior of the nanotube suspensions.

Dispersion and orientation of single-walled carbon nanotubes in a chromonic liquid crystal

A post-synthesis alignment of individual single-walled carbon nanotubes (SWCNTs) is desirable for translating their unique anisotropic properties to a macroscopic scale. Here, we demonstrate excellent dispersion, orientation and concomitant-polarised photoluminescence of SWCNTs in a nematic chromonic liquid crystal. The methods to obtain stable suspension are described, and order parameters of the liquid crystal matrix and of the nanotubes are measured independently.

Dispersion and film-forming properties of poly(acrylic acid)-stabilized carbon nanotubes.

We present a detailed study of the influence of pH on the dispersion and film-forming properties of poly(acrylic acid)-stabilized carbon nanotubes. Poly(acrylic acid) (PAA) is a weak polyelectrolyte, with a pH-responsive behavior in aqueous solution. We obtain quantitative UV-visible measurements to show that the amount of polyelectrolyte in optimal pH conditions is weak, showing a good efficiency of the polymer as a carbon nanotube dispersing agent. The best dispersion conditions are achieved at pH 5, a value close to the pK(a) of PAA. Apart from this tenuous pH value, the PAA is not efficient at stabilizing nanotubes and atomic force microscopy allows us to explain the delicate balance between the PAA adsorption and the suspension stability. This study finally permits optimal conditions for making homogeneous and conductive composite films to be determined.

A chemically reactive spinning dope for significant improvements in wet spun carbon nanotube fibres

Single-walled carbon nanotubes can be spun in a polyvinyl alcohol stream to produce nanocomposite fibres. We use a facile ester linking between both elements to create improved fibres which exhibit outstanding enhancements in the absence of post-processing stages, providing a promising alternative based on a chemical method.

Sensitivity of Carbon Nanotubes to the Storage of Stress in Polymers

Residual stress in polymers arises from the freezing of unstable molecular conformations. Residual stress is critical because its relaxation can cause shrinkage, defects, and fractures of polymer materials. The storage of stress is purposely enhanced to develop shape memory materials. Unfortunately, the storage of mechanical stress is still poorly controlled and understood. An approach to sense the storage of stress based on the spectroscopic response of carbon nanotubes is explored. The Raman response of nanotubes exhibits a variable sensitivity to strain when embedded in polymers that have experienced different thermal and mechanical treatments. This unique feature opens up new possibilities for the use of carbon nanotubes as mechanical nanosensors.