Massimiliano Polidori

Decay Heat Removal and Transient Analysis in Accidental Conditions in the EFIT Reactor

The development of a conceptual design of an industrial-scale transmutation facility (EFIT) of several 100 MW thermal power based on accelerator-driven system (ADS) is addressed in the frame of the European EUROTRANS Integral Project. In normal operation, the core power of EFIT reactor is removed through steam generators by four secondary loops fed by water. A safety-related decay heat removal (DHR) system provided with four independent inherently safe loops is installed in the primary vessel to remove the decay heat by natural convection circulation under accidental conditions which are caused by a loss-of-heat sink (LOHS). In order to confirm the adequacy of the adopted solution for decay heat removal in accidental conditions, some multi-D analyses have been carried out with the SIMMER-III code. The results of the SIMMER-III code have been then used to support the RELAP5 1D representation of the natural circulation flow paths in the reactor vessel. Finally, the thermal-hydraulic RELAP5 code has been employed for the analysis of LOHS accidental scenarios.

Cross-Comparison of One-Dimensional Thermal-Hydraulic Codes on Natural Circulation Analysis of NACIE Loop Test for Lead-Alloy Cooled Advanced Nuclear Energy Systems (LACANES)

As one of the Generation-IV reactor concepts, lead-alloy-cooled advanced nuclear energy systems (LACANES) have been studied worldwide in order to utilize the advantages of good heat transfer properties, neutron transparency and chemical inertness with air and water. Since the Fukushima accident, the passive safety aspect of the LACANES is increasingly emphasized due to outstanding natural circulation capability. To investigate the thermal-hydraulic capability of LBE, an international cooperation has been performed under OECD/NEA program, under the guidance of the Nuclear Science Committee by a task force named as Lead Alloy Cooled Advanced Nuclear Energy Systems (LACANES) since 2007. This international collaboration had dealt with computational benchmarking of isothermal LBE forced convection tests in the phase I, and the working group published a guideline for using one-dimensional system codes to simulate LBE forced circulation test results from HELIOS loop. The phase II was started after that, to give an additional guideline in the case of natural circulation. NACIE, one of benchmarking targets for the phase II which is a rectangular-shape loop located at ENEA-Brasimone Research Centre, Italy. NACIE test results were benchmarked by each participant using their one-dimensional thermal-hydraulic codes, and they are to follow the guideline from the LACANES phase I for regions where hydraulic loss occurs. Due to the selection of hydraulic loss coefficient relations by users, the cross-comparison results of international participants showed some discrepancies and the estimated mass flow rates had 13% of maximum error. Also, the future R&D areas are identified.Copyright

Preliminary Results on the Coupling of a Three-Dimensional Lead Fast Reactor Model and a One-Dimensional External Loop

An accurate three-dimensional simulation of all the components of the primary circuit of a LFR (Lead Fast Reactor) cannot be performed with the current computational power. One strategy to deal with such complex systems is to adopt a multi-scale approach, where different models and geometric representations are introduced for different parts of the reactor. This paper presents a preliminary assessment of a methodology developed in the framework of the FEM-LCORE code to simulate an accident scenario where natural circulation plays a key role in the heat removal.Copyright

Validation of CATHARE V2.5 Thermal-Hydraulic Code Against Full-Scale PERSEO Tests for Decay Heat Removal in LWRs

The PERSEO experimental program was performed in the framework of a domestic research program on innovative safety systems with the purpose to increase the reliability of passive decay heat removal systems implementing in-pool heat exchangers. The conceived system was tested at SIET laboratories by modifying the existing PANTHERS IC-PCC facility utilized in the past for testing a full scale module of the GE-SBWR in-pool heat exchanger. Integral tests and stability tests were conducted to verify the operating principles, the steadiness and the effectiveness of the system. Two of the more representative tests have been analyzed with CATHARE V2.5 for code validation purposes. The paper deals with the comparison of code results against experimental data. The capabilities and the limits of the code in simulating such kind of tests are highlighted. An improvement in the modeling of the large water reserve pool is suggested trying to reduce the discrepancies observed between code results and test measurements.Copyright

Analysis of Protected Accidental Transients in the EFIT Reactor With the RELAP5 Thermal-Hydraulic Code

The European Facility for Industrial Transmutation (EFIT) is aimed at demonstrating the feasibility of transmutation process through the Accelerator Driven System (ADS) route on an industrial scale. The conceptual design of this reactor of about 400 MW thermal power is under development in the frame of the European EUROTRANS Integrated Project of the EURATOM Sixth Framework Program (FP6). EFIT is a pool-type reactor cooled by forced circulation of lead in the primary system where the heat is removed by steam generators installed inside the reactor vessel. The reactor power is sustained by a spallation neutron source supplied by a proton beam impinging on a lead target at the core centre. A safety-related Decay Heat Removal (DHR) system provided with four independent inherently safe loops is installed in the primary vessel to remove the decay heat in case of loss of secondary circuits heat removal capability. A quite detailed model of the EFIT reactor has been developed for the RELAP5 thermal-hydraulic code to be used in preliminary accidental transient analyses aimed at verifying the validity of the adopted solutions for the current reactor design with respect to the safety requirements, and confirm the inherent safety behavior of the reactor, such as decay heat removal in accidental conditions relying on natural circulation in the primary system. The accident analyses for the EFIT reactor include both protected and unprotected transients, on whether the reactor automatic trip, consisting in proton beam switch off, is actuated or not by the protection system. In this paper, the main results of the analyses of some protected transients with RELAP5 are presented. The analyzed transients concern the Protected Loss of Heat Sink (PLOHS), in which the DHR system plays a key role in bringing the reactor in safe conditions, and the Protected Loss of Flow (PLOF) transients with partial or total loss of forced circulation in the primary system.Copyright