Mathias Christensen

Efficient generation of 1.9 W yellow light by cascaded frequency doubling of a distributed Bragg reflector tapered diode

Watt-level yellow emitting lasers are interesting for medical applications, due to their high hemoglobin absorption, and for efficient detection of certain fluorophores. In this paper, we demonstrate a compact and robust diode-based laser system in the yellow spectral range. The system generates 1.9 W of single-frequency light at 562.4 nm by cascaded single-pass frequency doubling of the 1124.8 nm emission from a distributed Bragg reflector (DBR) tapered laser diode. The absence of a free-space cavity makes the system stable over a base-plate temperature range of 30 K. At the same time, the use of a laser diode enables the modulation of the pump wavelength by controlling the drive current. This is utilized to achieve a power modulation depth above 90% for the second harmonic light, with a rise time below 40  μs.

Megahertz measurement rate wavemeter with sub-picometer resolution using second harmonic generation

Information on the wavelength is essential for most laser applications and a wide range of devices are available for measuring it. Commercially available wavemeters can provide femtometer resolution in a wide wavelength range but their refresh rate rarely goes into the kHz range. Streak cameras, on the other hand, provide extremely fast measurements with a wide spectrum. However, the spectral resolution is severely limited due to the use of a grating as the wavelength separating element. Here we present a wavemeter that combines a megahertz measurement rate and sub-picometer wavelength resolution. The technique uses the steep wavelength acceptance curve of a thick non-linear crystal to calculate the wavelength from just two power measurements. The bandwidth is limited only by the speed of a photodiode while the resolution and wavelength range can be engineered by choosing a suitable crystal type and geometry. We use the wavemeter to examine how the longitudinal mode evolves during a single pulse from a tapered diode laser. High resolution, high speed measurements of the wavelength can give new information about laser diodes, which is valuable for applications requiring short but wavelength stable pulses, such as pulsing of the second harmonic light.

Diffraction-limited 577 nm true-yellow laser by frequency doubling of a tapered diode laser

A wide range of laser medical treatments are based on coagulation of blood by absorption of the laser radiation. It has, therefore, always been a goal of these treatments to maximize the ratio of absorption in the blood to that in the surrounding tissue. For this purpose lasers at 577 nm are ideal since this wavelength is at the peak of the absorption in oxygenated hemoglobin. Furthermore, 577 nm has a lower absorption in melanin when compared to green wavelengths (515 − 532 nm), giving it an advantage when treating at greater penetration depth. Here we present a laser system based on frequency doubling of an 1154 nm Distributed Bragg Reflector (DBR) tapered diode laser, emitting 1.1 W of single frequency and diffraction limited yellow light at 577 nm, corresponding to a conversion efficiency of 30.5%. The frequency doubling is performed in a single pass configuration using a cascade of two bulk non-linear crystals. The system is power stabilized over 10 hours with a standard deviation of 0.13% and the relative intensity noise is measured to be 0.064 % rms.

Modulation of Frequency Doubled DFB-Tapered Diode Lasers for Medical Treatment

The use of visible lasers for medical treatments is on the rise, and together with this comes higher expectations for the laser systems. For many medical treatments, such as ophthalmology, doctors require pulse on demand operation together with a complete extinction of the light between pulses. We have demonstrated power modulation from 0.1 Hz to 10 kHz at 532 nm with a modulation depth above 97% by wavelength detuning of the laser diode. The laser diode is a 1064 nm monolithic device with a distributed feedback (DFB) laser as the master oscillator (MO), and a tapered power amplifier (PA). The MO and PA have separate electrical contacts and the modulation is achieved with wavelength tuning by adjusting the current through the MO 40 mA.

1.9 W yellow, CW, high-brightness light from a high efficiency semiconductor laser-based system

Semiconductor lasers are ideal sources for efficient electrical-to-optical power conversion and for many applications where their small size and potential for low cost are required to meet market demands. Yellow lasers find use in a variety of bio-related applications, such as photocoagulation, imaging, flow cytometry, and cancer treatment. However, direct generation of yellow light from semiconductors with sufficient beam quality and power has so far eluded researchers. Meanwhile, tapered semiconductor lasers at near-infrared wavelengths have recently become able to provide neardiffraction- limited, single frequency operation with output powers up to 8 W near 1120 nm. We present a 1.9 W single frequency laser system at 562 nm, based on single pass cascaded frequency doubling of such a tapered laser diode. The laser diode is a monolithic device consisting of two sections: a ridge waveguide with a distributed Bragg reflector, and a tapered amplifier. Using single-pass cascaded frequency doubling in two periodically poled lithium niobate crystals, 1.93 W of diffraction-limited light at 562 nm is generated from 5.8 W continuous-wave infrared light. When turned on from cold, the laser system reaches full power in just 60 seconds. An advantage of using a single pass configuration, rather than an external cavity configuration, is increased stability towards external perturbations. For example, stability to fluctuating case temperature over a 30 K temperature span has been demonstrated. The combination of high stability, compactness and watt-level power range means this technology is of great interest for a wide range of biological and biomedical applications.

Photo-electro Catalytic Water Splitting over Pure and Modified Iron Oxide Thin Films

Photo-catalysis offers the possibility to utilize solar energy to split water, thereby extracting chemical energy in the form of hydrogen. The general challenge is to synthesize a material with the right electronic and chemical properties for efficiently driving the process, while being sustainable in terms of stability and costs. The focus of this bachelor thesis is photo-electrocatalytic splitting of water on modified iron oxide thin films. Through various surface treatments and modification of thin film compositions, this material has shown that its water splitting properties can be improved.