Maxime J.-F. Guinel

Surface energy engineering for tunable wettability through controlled synthesis of MoS2.

MoS2 is an important member of the transition metal dichalcogenides that is emerging as a potential 2D atomically thin layered material for low power electronic and optoelectronic applications. However, for MoS2 a critical fundamental question of significant importance is how the surface energy and hence the wettability is altered at the nanoscale in particular, the role of crystallinity and orientation. This work reports on the synthesis of large area MoS2 thin films on insulating substrates (SiO2/Si and Al2O3) with different surface morphology via vapor phase deposition by varying the growth temperatures. The samples were examined using transmission electron microscopy and Raman spectroscopy. From contact angle measurements, it is possible to correlate the wettability with crystallinity at the nanoscale. The specific surface energy for few layers MoS2 is estimated to be about 46.5 mJ/m(2). Moreover a layer thickness-dependent wettability study suggests that the lower the thickness is, the higher the contact angle will be. Our results shed light on the MoS2-water interaction that is important for the development of devices based on MoS2 coated surfaces for microfluidic applications.

Bottom-up solution synthesis of narrow nitrogen-doped graphene nanoribbons.

Large quantities of narrow graphene nanoribbons with edge-incorporated nitrogen atoms can be synthesized via Yamamoto coupling of molecular precursors containing nitrogen atoms followed by cyclodehydrogenation using Scholl reaction.

EFhd2 is a novel amyloid protein associated with pathological tau in Alzheimer's disease

EFhd2 is a conserved calcium‐binding protein, abundant within the central nervous system. Previous studies identified EFhd2 associated with pathological forms of tau proteins in the tauopathy mouse model JNPL3, which expresses the human tauP301L mutant. This association was validated in human tauopathies, such as Alzheimers disease (AD). However, the role that EFhd2 may play in tauopathies is still unknown. Here, we show that EFhd2 formed amyloid structures in vitro, a capability that is reduced by calcium ions. Electron microscopy (EM) analyses demonstrated that recombinant EFhd2 formed filamentous structures. EM analyses of sarkosyl‐insoluble fractions derived from human AD brains also indicated that EFhd2 co‐localizes with aggregated tau proteins and formed granular structures. Immunohistological analyses of brain slices demonstrated that EFhd2 co‐localizes with pathological tau proteins in AD brains, confirming the co‐aggregation of EFhd2 and pathological tau. Furthermore, EFhd2s coiled‐coil domain mediated its self‐oligomerization in vitro and its association with tau proteins in JNPL3 mouse brain extracts. The results demonstrate that EFhd2 is a novel amyloid protein associated with pathological tau proteins in AD brain and that calcium binding may regulate the formation of EFhd2s amyloid structures. Hence, EFhd2 may play an important role in the pathobiology of tau‐mediated neurodegeneration.

Influence of nanostructured ceria support on platinum nanoparticles for methanol electrooxidation in alkaline media

The catalytic activity of platinum (Pt) nanoparticles (NPs) towards methanol electrooxidation in alkaline media was demonstrated to be dependent on their interactions with their nanostructured ceria support. Ceria nanorods (NRs) with diameters of 5 to 10 nm and lengths of 15 to 50 nm as well as ceria NPs with diameters of 2 to 6 nm were applied as supports for similarly sized Pt NPs with diameters of 2 to 5 nm. Cyclic voltammetry data showed that Pt NPs supported on ceria NPs exhibited a 2-to-5-fold higher catalytic current density versus ceria NRs. X-ray photoelectron spectroscopic data indicated that Pt NPs deposited onto ceria NRs were disproportionally composed of oxidized species (Pt2+, Pt4+ and Pt–O–M) rather than Pt0 while Pt NPs on ceria NPs mainly consisted of Pt0. Stronger metal-support interactions between Pt NPs and ceria NRs are postulated to induce preferential oxidation of Pt NPs and consequently decrease the catalytic sites and overall activity.

Temperature dependent Raman scattering studies of three dimensional topological insulators Bi2Se3

We investigate the temperature dependent (83 K≤T≤523 K) frequency shift of 2Ag1 and 1Eg2 phonon modes in the three dimensional topological insulator Bi2Se3, using Raman spectroscopy. The high quality single crystals of Bi2Se3 were grown using a modified Bridgman technique and characterized by Laue diffraction and high resolution transmission electron microscopy. A significant broadening in the line shape and red-shift in the frequencies were observed with increase in temperature. Polarized Raman scattering measurement shows a strong polarization effect of Ag1 and Ag2 phonon modes which confirms the good quality single crystals of Bi2Se3. Temperature co-efficient for A1g1, Eg2, and A1g2 modes was estimated to be −1.44 × 10−2, −1.94 × 10−2, and −1.95 × 10−2 cm−1∕K, respectively. Our results shed light on anharmonic properties of Bi2Se3.

Microscopy and microanalysis of complex nanosized strengthening precipitates in new generation commercial Al–Cu–Li alloys

Precipitates (ppts) in new generation aluminum–lithium alloys (AA2099 and AA2199) were characterised using scanning and transmission electron microscopy and atom probe tomography. Results obtained on the following ppts are reported: Guinier–Preston zones, T1 (Al2CuLi), β’ (Al3Zr) and δ’ (Al3Li). The focus was placed on their composition and the presence of minor elements. X‐ray energy‐dispersive spectrometry in the electron microscopes and mass spectrometry in the atom probe microscope showed that T1 ppts were enriched in zinc (Zn) and magnesium up to about 1.9 and 3.5 at.%, respectively. A concentration of 2.5 at.% Zn in the δ’ ppts was also measured. Unlike Li and copper, Zn in the T1 ppts could not be detected using electron energy‐loss spectroscopy in the transmission electron microscope because of its too low concentration and the small sizes of these ppts. Indeed, Monte Carlo simulations of EEL spectra for the Zn L2,3 edge showed that the signal‐to‐noise ratio was not high enough and that the detection limit was at least 2.5 at.%, depending on the probe current. Also, the simulation of X‐ray spectra confirmed that the detection limit was exceeded for the Zn Kα X‐ray line because the signal‐to‐noise ratio was high enough in that case, which is in agreement with our observations.

Magnetothermal repair of a PMMA/iron oxide magnetic nanocomposite

We report on the magnetothermal repair of a thermoplastic magnetic nanocomposite consisting of iron oxide nanoparticles embedded in poly(methyl methacrylate) (PMMA). The nanoparticles responded to an applied alternating magnetic field by dissipating heat, raising the nanocomposite temperature to above the glass transition temperature and resulting in the repair of the nanocomposite. This was demonstrated by cutting the nanocomposite and subsequently joining two pieces together under the action of an alternating magnetic field. Examination by optical and transmission electron microscopy of the region where the two pieces were joined demonstrated the healing and disappearance of the interface between both pieces down to the nanoscale.

Curing of a Bisphenol E Based Cyanate Ester Using Magnetic Nanoparticles as an Internal Heat Source through Induction Heating

We report on the control of cyclotrimerization forming a polycyanurate polymer using magnetic iron oxide nanoparticles in an alternating-current (ac) field as an internal heat source, starting from a commercially available monomer. Magnetic nanoparticles were dispersed in the monomer and catalytic system using sonication, and the mixture was subjected to an alternating magnetic field, causing the magnetic nanoparticles to dissipate the energy of the magnetic field in the form of heat. Internal heating of the particle/monomer/catalyst system was sufficient to start and sustain the polymerization reaction, producing a cyanate ester network with conversion that compared favorably to polymerization through heating in a conventional laboratory oven. The two heating methods gave similar differential scanning calorimetry temperature profiles, conversion rates, and glass transition temperatures when using the same temperature profile. The ability of magnetic nanoparticles in an ac field to drive the curing reaction should allow for other reactions forming high-temperature thermosetting polymers and for innovative ways to process such polymers.

Single-step route to diamond-nanotube composite

Candle wax was used as a precursor for the production of a diamond-nanotube composite in a single step. The composite films were fabricated by sulfur-assisted hot-filament chemical vapor deposition technique. The morphology of the composite films was analyzed by scanning electron microscopy and transmission electron microscopy. Raman spectra of the films show characteristic diamond band at 1,332 cm−1, D-band around 1,342 cm−1, and graphitic G-band around 1,582 cm−1. The electron energy-loss spectroscopy recorded at the carbon K-edge region shows signature features of diamond and carbon nanotube in the fabricated material. The ability to synthesize diamond-nanotube composites at relatively low temperatures by a single-step process opens up new possibilities for the fabrication of nanoelectronic devices.

Nickel oxide crystalline nano flakes: synthesis, characterization and their use as anode in lithium-ion batteries

Nickel oxide crystalline nano flakes (NONFs)—only about 10 nm wide—were produced using a simple and inexpensive chemistry method followed by a short annealing in ambient air. In a first step, Ni(OH)2 sheets were synthesized by adding sodium hydroxide (NaOH) drop-wise in a Ni(NO3)2 aqueous solution that was then sonicated for up to 60 min, washed and vigorously stirred overnight in deionized water. In a second step, the products of this reaction were annealed in ambient air in the temperature range 285–450 °C producing the desired NONFs. The products were characterized using x-ray diffraction, scanning electron microscopy and high resolution transmission electron microscopy including electron diffraction and electron energy-loss spectroscopy. Electrochemical investigations showed that anodes made of these NONFs provided significantly higher discharge capacities (70 to 100% higher) compared to commercial nanometric NiO nanopowder used under the same conditions. Moreover, these NONFs had higher initial capacity retentions at both low and high current densities compared to the same NiO nanopowder.