Michael Eldred

Current status of the laser guide star adaptive optics system for Subaru Telescope

The current status and recent results, since last SPIE conference at Orlando in 2006, for the laser guide star adaptive optics system for Subaru Telescope is presented. We had a first light using natural guide star and succeed to launch the sodium laser beam in October 2006. The achieved Strehl ratio on the 10th magnitude star was around 0.5 at K band. We confirmed that the full-width-half-maximum of the stellar point spread function is smaller than 0.1 arcsec even at the 0.9 micrometer wavelehgth. The size of the artificial guide star by the laser beam tuned at the wavelength of 589 nm was estimated to be 10 arcsec. The obtained blurred artificial guide star is caused by the wavefront error on the laser launching telescope. After the first light and first launch, we found that we need to modify and to fix the components, which are temporarily finished. Also components, which were postponed to fabricate after the first light, are required to build newly. All components used by the natural guide star adaptive optics system are finalized recently and we are ready to go on the sky. Next engineering observation is scheduled in August, 2008.

Status of Subaru laser guide star AO system

The laser guide star adaptive optics (AO188) system for Subaru Telescope is presented. The system will be installed at the IR Nasmyth platform of Subaru 8 m telescope, whereas the current AO system with 36 elements is operating at the Cassegrain focus. The new AO system has a 188 element wavefront curvature sensor with photon counting APD modules and 188 element bimorph mirror. The laser guide star system has a 4.5 W solid state sum-frequency laser on the Nasmyth platform. The laser launching telescope with 50 cm aperture will be installed at behind the secondary mirror. The laser beam will be transferred to the laser launching telescope using photonic crystal single mode fiber cable. The instrument with the AO system is IRCS, infrared camera and spectrograph which has been used for Cassegrain AO system and new instrument, HiCIAO, high dynamic range infrared camera for exsolar planet detection. The first light of the AO system is planned in 2006.

Design of laser system for Subaru LGS AO

We present the development status of the laser system for Subaru Laser Guide Star Adaptive Optics System. We are manufacturing the quasi-continuous-wave sum frequency laser as a prototype. The optical efficiency of sum frequency generation normalized by the mode-locked fundamental YAG (1064 nm) laser output power is achieved to be 14 % using the non-linear crystal, periodically poled potassium titanyl phosphate (PPKTP). Output power at sodium D2 line was about 260 mW. The optical relay fiber and the laser launching telescope are also described in this paper. For the optical relay fiber, we are testing an index guided photonic crystal fiber (PCF), whose core material is filled by fused silica, and whose clad has close-packed air holes in two dimension. The coupling efficiency was evaluated as about 80 % using 1mW He-Ne laser. We introduce the design of laser launching telescope (LLT), which is a copy of VLT laser launching telescope, and the interface to the Subaru Telescope.

The laser guide star facility for Subaru Telescope

The purpose of this paper is to report on the current status of developing the new laser guide star (LGS) facility for the Subaru LGS adaptive optics (AO) system. Since two major R&D items, the 4W-class sum-frequency generating laser1 and the large-area-core photonic crystal fiber2, have been successfully cleared, we are almost ready to install the LGS facility to the Subaru Telescope. Also we report the result for LGS generation in Japan.

Deformable mirror design of Subaru LGSAO system

As an upgrade plan of Subaru adaptive optics facility, laser-guide-star adaptive-optics (LGSAO) project is on going. One of key components of the project is a deformable mirror (DM). The DM for LGSAO is a bimorph type of PZT with 188 control elements. The specification of design is presented together with the analysis of stroke and vibration properties by FEM.

Performance of the deformable mirror for Subaru LGSAO

The performance of a deformable mirror with 188 electrodes is reported in this paper. The deformable mirror has been manufactured by CILAS for a new adaptive optics system at Subaru Telescope equipped with laser-guide-star. The type of deformable mirror is bimorph PZT with the blank diameter of 130 mm (beam size 90 mm).

589 nm sum-frequency generation laser for the LGS/AO of Subaru Telescope

We developed a high power and high beam quality 589 nm coherent light source by sum-frequency generation in order to utilize it as a laser guide star at the Subaru telescope. The sum-frequency generation is a nonlinear frequency conversion in which two mode-locked Nd:YAG lasers oscillating at 1064 and 1319 nm mix in a nonlinear crystal to generate a wave at the sum frequency. We achieved the qualities required for the laser guide star. The power of laser is reached to 4.5 W mixing 15.65 W at 1064 nm and 4.99 W at 1319 nm when the wavelength is adjusted to 589.159 nm. The wavelength is controllable in accuracy of 0.1 pm from 589.060 and 589.170 nm. The stability of the power holds within 1.3% during seven hours operation. The transverse mode of the beam is the TEM00 and M2 of the beam is smaller than 1.2. We achieved these qualities by the following technical sources; (1) simple construction of the oscillator for high beam quality, (2) synchronization of mode-locked pulses at 1064 and 1319 nm by the control of phase difference between two radio frequencies fed to acousto-optic mode lockers, (3) precise tunability of wavelength and spectral band width, and (4) proper selection of nonlinear optical crystal. We report in this paper how we built up each technical source and how we combined those.

Subaru Telescope LGSAO: overview of expected performance

The Subaru Telescope LGSAO system is a 188 elements curvature AO system currently under construction, and scheduled to have first light in March 2006 for the Natural Guide Star mode and March 2007 for the Laser Guide Star mode. A particularity of this system will be to perform curvature wavefront sensing with several extra-pupil distances, which significantly improves the closed-loop performance. An overview of the predicted performance of the system is given for Natural Guide Star and Laser Guide Star modes.

Transmission characteristics of high-power 589-nm laser beam in photonic crystal fiber

We are developing Laser Guide Star Adaptive Optics (LGSAO) system for Subaru Telescope at Hawaii, Mauna Kea. We achieved an all-solid-state 589.159 nm laser in sum-frequency generation. Output power at 589.159 nm reached 4W in quasi-continuous-wave operation. To relay the laser beam from laser location to laser launching telescope, we used an optical fiber because the optical fiber relay is more flexible and easier than mirror train. However, nonlinear scattering effect, especially stimulated Raman scattering (SRS) and stimulated Brillouin scattering (SBS), will happen when the inputted laser power increases, i.e., intensity at the fiber core exceed each threshold. In order to raise the threshold levels of each nonlinear scattering, we adopt photonic crystal fiber (PCF). Because the PCF can be made larger core than usual step index fiber (SIF), one can reduce the intensity in the core. We inputted the high power laser into the PCF whose mode field diameter (MFD) is 14 μm and the SIF whose MFD is 5 μm, and measured the transmission characteristics of them. In the case of the SIF, the SRS was happen when we inputted 2 W. On the other hand, the SRS and the SBS were not induced in the PCF even for an input power of 4 W. We also investigated polarization of the laser beam transmitting through the PCF. Because of the fact that the backscattering efficiency of exciting the sodium layer with a narrowband laser is dependent on the polarization state of the incident beam, we tried to control the polarization of the laser beam transmitted the PCF. We constructed the system which can control the polarization of input laser and measure the output polarization. The PCF showed to be able to assume as a double refraction optical device, and we found that the output polarization is controllable by injecting beam with appropriate polarization through the PCF. However, the Laser Guide Star made by the beam passed through the PCF had same brightness as the state of the polarization.

Histopathology Reconstruction on Digital Imagery

Diagnosing cervical cancer in a woman is a multi-step procedure involving examination of the cervix, possible biopsy and follow-up. It is open to subjective interpretation and highly dependent upon the skills of cytologists, colposcopists, and pathologists. In an effort to reduce the subjectiveness of the colposcopist-directed biopsy and to improve the diagnostic accuracy of colposcopy, we have developed new colposcopic imaging systems with accompanying computer aided diagnostic (CAD) techniques to guide a colposcopist in deciding if and where to biopsy. If the biopsys histopathology, the identification of the disease state at the cellular and near-cellular level, is to be used as the gold standard for CAD, then the location of the histopathologic analysis must match exactly to the location of the biopsy tissue in the digital image. Otherwise, no matter how perfect the histopathology and the quality of the digital imagery, the two data sets cannot be matched and the true sensitivity and specificity of the CAD cannot be ascertained. We report here on new approaches to preserving, continuously, the location and orientation of a biopsy sample with respect to its location in the digital image of the cervix so as to preserve the exact spatial relationship throughout the mechanical aspects of the histopathologic analysis. This new approach will allow CAD to produce a linear diagnosis and pinpoint the location of the tissue under examination.