Miroslav Polášek

On-line coupling of capillary isotachophoresis and capillary zone electrophoresis for the determination of flavonoids in methanolic extracts of Hypericum perforatum leaves or flowers

Five flavonoids (hyperoside, isoquercitrin, quercitrin, quercetin and rutin) were separated and determined in extracts of Hypericum perforatum leaves or flowers by capillary zone electrophoresis (CZE) with isotachophoretic (ITP) sample pre-treatment using on-line column coupling configuration. The background electrolyte (BGE) used in the CZE step was different from the leading and terminating ITP electrolytes but all the electrolytes contained 20% (v/v) of methanol. The optimal leading electrolyte was 10 mM HCl of pH* approximately 7.2 (adjusted with Tris) and the terminating electrolyte was 50 mM H3BO3 of pH* approximately 8.2 (adjusted with barium hydroxide). This operational system allowed to concentrate and pre-separate selectively the flavonoid fraction from other plant constituents before the introduction of the flavonoids into the CZE capillary. The BGE for the CZE step was 50 mM Tris buffer of pH* approximately 8.75 containing 25 mM N-[tris(hydroxymethyl)methyl]-3-aminopropanesulfonic acid as co-ion and 55 mM H3BO3 as complex-forming agent. The ITP-CZE method with spectrophotometric detection at 254 nm was suitable for the quantitation of the flavonoids in real natural samples; kaempferol was used as internal standard. The limit of detection for quercetin-3-O-glycosides was 100 ng ml(-1) and calibration curves were rectilinear in the range 1-10 microg ml (-1) for most of the analytes. The RSD values ranged between 0.9 and 2.7% (n=3) when determining approximately 0.07-1.2% of the individual flavonoids in dried medicinal plants.

Determination of procaine, benzocaine and tetracaine by sequential injection analysis with permanganate-induced chemiluminescence detection

Local anaesthetics procaine hydrochloride (I), benzocaine (II), and tetracaine hydrochloride (III) were determined by the technique of sequential injection analysis (SIA) with chemiluminescence (CL) detection. The CL was emitted during the oxidation of the analytes by permanganate in aqueous sulphuric acid in the presence of various CL enhancers (4-hydroxybiphenyl, Rhodamine B, glycolaldehyde, glutaraldehyde and formic acid). The optimum enhancer or reagent concentrations, order and volumes of the injected zones were: 0.37 M formic acid (40, 23 or 28 mul for I-III, respectively), sample (40 mul), 2.3 M H(2)SO(4) (20, 16 or 18 mul for I-III, respectively), and 0.5 mM KMnO(4) (19, 13 or 15 mul for I-III, respectively). After a double (or single for III) reversal of the flow the mixed zone was pushed into the detector at a flow rate of 100 mul s(-1). The transient CL signal was recorded at >/=390 nm. The calibration graphs relating the intensity of the emission (peak heights) to the concentration of the analytes were curvilinear (a second order polynomial showed the best fit) and they were suitable for determining I-III in the ranges 0.5-50, 0.5-25 and 0.2-25 mug ml(-1), respectively. The limits of detection (3sigma) were 0.3 mug ml(-1) for I and II and 0.1 mug ml(-1) for III. The sample throughput was 120 h(-1). The relative standard deviations were </=3.8% (n=10) when determining 5 mug ml(-1) of I-III in prepared pure test solutions. The I and II were assayed in pharmaceutical dosage forms by the proposed method and the SIA results did not show any statistically significant difference from those obtained by standard titrimetry with sodium nitrite.

Amperometric glucose sensor based on glucose dehydrogenase immobilized on a graphite electrode modified with an N,N′-bis(benzophenoxazinyl) derivative, of benzene-1,4-dicarboxamide

Abstract A bis(benzophenoxazinyl) derivative of benzene-1,4-dicarboxamide (BPT) was synthesized by coupling Nile Blue with terephthaloyl chloride. The BPT adsorbed on a graphite rod electrode catalysed the electrochemical oxidation of 1,4-dihydronicotinamide adenine dinucleotide (NADH) at potentials more positive than −200 mV vs. Ag/AgCl at pH 7.0. When using BPT-modified electrodes as the amperometric sensors in a single-channel flow-injection system, rectilinear calibration graphs were obtained in the range 0.3 μM−2 mM NADH for 50-μl samples injected. No decrease in the response to NADH was observed for at least 2 weeks of continuous daily operation of the sensor at pH 5–9. An amperometric glucose sensor was prepared by cross-linking glucose dehydrogenase with glutaraldehyde on the surface of a BPT-modified electrode. Its response to glucose and to NADH remained constant for 30 days of daily flow-injection experiments at pH 6.5. The calibration graphs were rectilinear for 3–500 μM glucose. A sample throughput of 200 h −1 was attained.

Determination of ambroxol or bromhexine in pharmaceuticals by capillary isotachophoresis

Expectorant drugs ambroxol (AX) and bromhexine (BX) were determined by capillary isotachophoresis (ITP) with conductimetric detection. The leading electrolyte (LE) was a buffer solution that contained 5 mM picolinic acid and 5 mM potassium picolinate (pH 5.2). The terminating electrolyte (TE) was 10 mM formic acid. The driving current was 80 microA (for approximately 200 s) or 50 microA (for approximately 350 s) and the detection current was 20 microA (a single analysis took about 8 min). The effective mobilities of AX and BX (evaluated with tetraethylammonium as the mobility standard) were 18.8 x 10(-9) m2 V(-1) s(-1) and 14.3 x 10(-9) m2 V(-1) s(-1) respectively. The calibration graphs relating the ITP zone length to the concentration of the analytes were rectilinear (r = 0.9993-0.9999) in the range 10 mg L(-1) (20 mg L(-1) for BX) to 200 mg l(-1) of the drug standard. The relative standard deviations (RSD) were 1.2 1.6% (n = 6) when determining 100 mg l(-1) of the analytes in pure test solutions. The method has been applied to the assay of AX or BX in seven commercial mass-produced pharmaceutical preparations. According to the validation procedure based on the standard addition technique the recoveries were 97.5-102.7% of the drug and the RSD values were 0.11-2.20% (n = 6).

Use of molybdate as novel complex-forming selector in the analysis of polyhydric phenols by capillary zone electrophoresis.

Molybdate was examined as a complex-forming additive to the CE background electrolytes (BGE) to affect the selectivity of separation of polyhydric phenols such as flavonoids (apigenin, hyperoside, luteolin, quercetin and rutin) and hydroxyphenylcarboxylic acids (ferulic, caffeic, p-coumaric and chlorogenic acid). Effects of the buffer concentrations and pH and the influence of molybdate concentration on the migration times of the analytes were investigated. In contrast to borate (which is a buffering and complex-forming agent generally used in CE at pH > or =9) molybdate forms more stable complexes with aromatic o-dihydroxy compounds and hence the complex-formation effect is observed at considerably lower pH. Model mixtures of cinnamic acid, ferulic acid, caffeic acid and 3-hydroxycinnamic acid were separated with 25 mM morpholinoethanesulfonic acid of pH 5.4 (adjusted with Tris) containing 0.15 mM sodium molybdate as the BGE (25 kV, silica capillary effective length 45 cm x 0.1mm I.D., UV-vis detection at 280 nm). With 25 mM 2-hydroxy-3-[4-(2-hydroxyethyl)-1-piperazinyl]propanesulphonic acid/Tris of pH* 7.4 containing 2mM sodium molybdate in aqueous 25% (v/v) methanol as the BGE mixtures of all the above mentioned flavonoids, p-coumaric acid and chlorogenic acid could be separated (the same capillary as above, UV-vis detection at 263 nm). The calibration curves (analyte peak area versus concentration) were rectilinear (r>0.998) for approximately 8-35 microg/ml of an analyte (with 1-nitroso-2-naphthol as internal standard). The limit of quantification values ranged between 1.1 mg l(-1) for p-coumaric acid and 2.8 mg l(-1) for quercetin. The CE method was employed for the assay of flavonoids in medicinal plant extracts. The R.S.D. values ranged between 0.9 and 4.7% (n=3) when determining luteolin (0.08%) and apigenin (0.92%) in dry Matricaria recutita flowers and rutin (1.03%) and hyperoside (0.82%) in dry Hypericum perforatum haulm. The recoveries were >96%.

Sequential injection technique applied to pharmaceutical analysis

The versatility of sequential injection analysis (SIA), based on programmable flow, has been recently enhanced by the miniaturization implemented in lab-on-valve (LOV) format. This article discusses the implication of this development and the use of SIA for chromatography and for bead injection, identifying a trend towards development of a versatile, multi-purpose analytical system.

Evaluation of natural antioxidants of Leuzea carthamoides as a result of a screening study of 88 plant extracts from the European Asteraceae and Cichoriaceae

In recently, there has been a great interest in natural antioxidants as bioactive components of food, nutraceuticals or potential drugs against several diseases. In our study, 88 extracts from various parts of plants from European Asteraceae and Cichoriaceae were assayed for radical scavenging activity by means of DPPH (1,1-diphenyl-2-picryl hydrazyl radical) test using the SIA (Sequential injection analysis) method developed for this purpose in our laboratory. DPPH radical scavenging activity of all tested plant extracts was evaluated according to the IC50 parameter. 29 extracts exhibited IC50 value lower than 0.1 mg/mL. The leaves of Leuzea carthamoides (IC50 = 0.046 mg/mL) were chosen as the most promising sample for a subsequent phytochemical study, which resulted in isolation of seven natural compounds, namely, 4′,5,7-trihydroxy-6-methoxyflavone (hispidulin) (1), 5, 7, 3′, 4′- tetrahydroxyflavanone (eriodictyol) (2), 3′,4′,5,7-pentahydroxy-6-methoxyflavonol (patuletin) (3), eriodictyol-7-β-glucopyranoside (4), 6-hydroxykaempferol-7-O-(6″-O-acetyl-β-D-glucopyranoside) (5), 4-hydroxybenzoic acid (6) and 3,4-dihydroxybenzoic acid (protocatechuic acid) (7). Antioxidant activity of the isolated compounds was evaluated by DPPH test and ferric reducing antioxidant power (FRAP) test and compared with trolox and quercetin. Both tests evaluated the flavonoid (5) as the most active antioxidant. This result was confirmed by comparison with known data concerning the structure/activity relationships of flavonoids.

Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l(-1) for copper and 0.1-5 mg l(-1) for iron, respectively, with a sampling rate of 18 h(-1). The limits of detection are 50 microg l(-1) for copper and 25 microg l(-1) for iron. The relative standard deviations (n=15) are 2% for 0.5 mg l(-1) copper and 1.8% for 0.5 mg l(-1) iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l(-1) of copper and 0.2-5 mg l(-1) of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.

Potentiometric determination of acetylsalicylic acid by sequential injection analysis (SIA) using a tubular salicylate-selective electrode

This paper deals with the development of an automated procedure for formulation assays and dissolution tests based on a sequential injection analysis (SIA) system involving an ion-selective electrode as sensing device. Construction of a tubular salicylate (Sal) selective electrode suitable for potentiometric determination of acetylsalicylic acid (Asa) in pharmaceutical formulations is described. The flow-through electrode is formed by a PVC membrane containing 29.2% (w/w) PVC, 5.8% (w/w) tetraoctylammonium salicylate (ionic sensor), 58.5% o-nitrophenyloctylether (plasticizer) and 6.5% (w/w) p-tert-octylphenol (stabilising additive which increases electrode selectivity). The calibration range is 0.05--10 mM Sal, the limit of detection (LOD) is 0.05 mM Sal, the slope is 56.0 mV per decade at 22 degrees C. The R.S.D. is 0.20% (15 readings) when determining 2.5 mM Sal in standard solution. The electrode is used for sensing Asa after its on-line chemical hydrolysis to Sal in a SIA system. The sampling rate is 6 h(-1) but for the dissolution tests the frequency is increased to 20 h(-1). The SIA set-up is employed for the assay of Asa in plain tablets, composed tablets and effervescent tablets and for performing dissolution tests of normal and sustained release tablets. Results obtained by this technique compare well with those required by the US Pharmacopoeia XXIV.

Determination of limiting ionic mobilities and dissociation constants of some local anaesthtics

The limiting ionic mobilities and thermodynamic acid dissociation constants were calculated from isotachophoretic experiments for the local anaesthetics procaine, tetracaine, lidocaine, trimecaine, bupivacaine, cinchocaine, diperodone, diocaine, cocaine, psicaine-neu, tropacocaine, amylocaine, beta-eucaine and leucinocaine. The pH values at which the local anaesthetics with very similar limiting ionic mobilities can be isotachophoretically separated were determined from simulated mobility curves. The measuring apparatus employed a high-frequency contactless conductivity detector.