Mitja Morgut

Numerical Predictions of Cavitating Flow around Model Scale Propellers by CFD and Advanced Model Calibration

The numerical predictions of the cavitating flow around two model scale propellers in uniform inflow are presented and discussed. The simulations are carried out using a commercial CFD solver. The homogeneous model is used and the influence of three widespread mass transfer models, on the accuracy of the numerical predictions, is evaluated. The mass transfer models in question share the common feature of employing empirical coefficients to adjust mass transfer rate from water to vapour and back, which can affect the stability and accuracy of the predictions. Thus, for a fair and congruent comparison, the empirical coefficients of the different mass transfer models are first properly calibrated using an optimization strategy. The numerical results obtained, with the three different calibrated mass transfer models, are very similar to each other for two selected model scale propellers. Nevertheless, a tendency to overestimate the cavity extension is observed, and consequently the thrust, in the most severe operational conditions, is not properly predicted.

Numerical simulation of flow in a high head Francis turbine with prediction of efficiency, rotor stator interaction and vortex structures in the draft tube

The paper presents numerical simulations of flow in a model of a high head Francis turbine and comparison of results to the measurements. Numerical simulations were done by two CFD (Computational Fluid Dynamics) codes, Ansys CFX and OpenFOAM. Steady-state simulations were performed by k- and SST model, while for transient simulations the SAS SST ZLES model was used. With proper grid refinement in distributor and runner and with taking into account losses in labyrinth seals very accurate prediction of torque on the shaft, head and efficiency was obtained. Calculated axial and circumferential velocity components on two planes in the draft tube matched well with experimental results.

Experimental and Numerical Prediction of the Hydrodynamic Performances of a 65 ft Planing Hull in Calm Water

An extensive campaign of model and full scale experimental tests as well as of numerical computations, aimed at the prediction of the hydrodynamic performances of a 65 ft motoryacht in calm water and in waves, is undertaken within the framework of the Project SOPHYA Seakeeping Of Planing Hull YAchts, co-financed by Friuli-Venezia Giulia Region in the field of joint industrial and academic research. In this paper, selected results of the numerical computations conducted by HyMOLabUniversity of Trieste and by the University of Zagreb for the calm water case are presented. The RANS simulations carried out in combination with a semi-automatic optimized mesh generation tool, developed in this project within the OpenFOAM/foamExtend framework, are described. Different free surface capturing methods are employed and compared, with focus on numerical issues. The numerical results are compared with new experimental data obtained at the towing tank of the University of Naples within the project, with uncertainty assessment.

Numerical Prediction of Cavitating Vortex Rope in a Draft Tube of a Francis Turbine with Standard and Calibrated Cavitation Model

Transient simulations of flow in a Francis turbine were performed with a goal to predict pressure pulsation frequencies and amplitudes caused by rotating vortex rope at part load operating regime. Simulations were done with the SAS SST turbulence model with curvature correction on basic and refined computational meshes. Without cavitation modelling too small values of frequency and amplitudes were obtained. With mesh refinement the calculated amplitudes were a bit closer to the measured values, while the accuracy of predicted frequency did not improve at all. Agreement between measured and numerical values was significantly improved when cavitation was included in simulations. In addition, the predicted value of the dominant frequency was slightly more accurate when, in the Zwart et al. cavitation model, the default condensation and evaporation model constants were replaced with previously calibrated ones.

Optimization of a single-stage double-suction centrifugal pump

In this study, the objective of the optimization of a double-suction pump is the maximization of its hydraulic efficiency. The optimization is performed, by means of the modeFRONTIER optimization platform, in steps. At first, by means of a DOE (Design of Experiments) strategy, the design space is explored, using a parameterized CAD representation of the pump. Suitable metamodels (surrogates or Response Surfaces), which represent an economical alternative to the more expensive 3D CFD model, are built and tested. Among different metamodels, the evolutionary design, radial basis function and the stepwise regression models seem to be the most promising ones. Finally, the stepwise regression model, trained on a set of 200 designs and constructed with only five the most influential input design parameters, was chosen as a potentially applicable metamodel.

Decoupled CFD-based optimization of efficiency and cavitation performance of a double-suction pump

In this study the impeller geometry of a double-suction pump ensuring the best performances in terms of hydraulic efficiency and reluctance of cavitation is determined using an optimization strategy, which was driven by means of the modeFRONTIER optimization platform. The different impeller shapes (designs) are modified according to the optimization parameters and tested with a computational fluid dynamics (CFD) software, namely ANSYS CFX. The simulations are performed using a decoupled approach, where only the impeller domain region is numerically investigated for computational convenience. The flow losses in the volute are estimated on the base of the velocity distribution at the impeller outlet. The best designs are then validated considering the computationally more expensive full geometry CFD model. The overall results show that the proposed approach is suitable for quick impeller shape optimization.

Numerical investigation of the flow in axial water turbines and marine propellers with scale-resolving simulations

The accurate prediction of the performances of axial water turbines and naval propellers is a challenging task, of great practical relevance. In this paper a numerical prediction strategy, based on the combination of a trusted CFD solver and a calibrated mass transfer model, is applied to the turbulent flow in axial turbines and around a model scale naval propeller, under non-cavitating and cavitating conditions. Some selected results for axial water turbines and a marine propeller, and in particular the advantages, in terms of accuracy and fidelity, of ScaleResolving Simulations (SRS), like SAS (Scale Adaptive Simulation) and Zonal-LES (ZLES) compared to standard RANS approaches, are presented. Efficiency prediction for a Kaplan and a bulb turbine was significantly improved by use of the SAS SST model in combination with the ZLES in the draft tube. Size of cavitation cavity and sigma break curve for Kaplan turbine were successfully predicted with SAS model in combination with robust high resolution scheme, while for mass transfer the Zwart model with calibrated constants were used. The results obtained for a marine propeller in non-uniform inflow, under cavitating conditions, compare well with available experimental measurements, and proved that a mass transfer model, previously calibrated for RANS (Reynolds Averaged Navier Stokes), can be successfully applied also within the SRS approaches.