Mohsin Saleemi

Synthesis, processing, and thermoelectric properties of bulk nanostructured bismuth telluride (Bi2Te3)

Bismuth telluride (Bi2Te3) is the best-known commercially used thermoelectric material in the bulk form for cooling and power generation applications at ambient temperature. However, its dimensionless figure-of-merit-ZT around 1 limits the large-scale industrial applications. Recent studies indicate that nanostructuring can enhance ZT while keeping the material form of bulk by employing an advanced synthetic process accompanied with novel consolidation techniques. Here, we report on bulk nanostructured (NS) undoped Bi2Te3 prepared via a promising chemical synthetic route. Spark plasma sintering has been employed for compaction and sintering of Bi2Te3 nanopowders, resulting in very high densification (>97%) while preserving the nanostructure. The average grain size of the final compacts was obtained as 90 ± 5 nm as calculated from electron micrographs. Evaluation of transport properties showed enhanced Seebeck coefficient (−120 μV K−1) and electrical conductivity compared to the literature state-of-the-art (30% enhanced power factor), especially in the low temperature range. An improved ZT for NS bulk undoped Bi2Te3 is achieved with a peak value of ∼1.1 at 340 K.

Fabrication, Characterization and Thermophysical Property Evaluation of SiC Nanofluids for Heat Transfer Applications

Nanofluids (NFs) are nanotechnology-based colloidal suspensions fabricated by suspending nanoparticles (NPs) in a base liquid. These fluids have shown potential to improve the heat transfer properties of conventional heat transfer fluids. In this study we report in detail on fabrication, characterization and thermo-physical property evaluation of SiC NFs, prepared using SiC NPs with different crystal structures, for heat transfer applications. For this purpose, a series of SiC NFs containing SiC NPs with different crystal structure (α-SiC and β-SiC) were fabricated in a water (W)/ethylene glycol (EG) mixture (50/50 wt% ratio). Physicochemical properties of NPs/NFs were characterized by using various techniques, such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fouriertransform infrared spectroscopy (FTIR), dynamic light scattering (DLS) and Zeta potential analysis. Thermo-physical properties including thermal conductivity (TC) and viscosity for NFs containing SiC particles (α- and β- phase) weremeasured. The results show among all suspensions NFs fabricated with α-SiC particles have more favorable thermo-physical properties compared to the NFs fabricated with β-SiC.The observed difference is attributed to combination of several factors, including crystal structure (β- vs. α-), sample purity, and residual chemicals exhibited on SiCNFs. A TC enhancement of ∼20% while 14% increased viscosity were obtained for NFs containing 9 wt% of particular type of α-SiC NPs indicating promising capability of this kind of NFs for further heat transfer characteristics investigation.

Removal of Chromium(VI) Using Surface Modified Superparamagnetic Iron Oxide Nanoparticles

This study describes the removal of Chromium(VI) from aqueous solutions using surface tailored superparamagnetic iron oxide nanoparticles (SPION) coated with bis(2,4,4-trimethylpentyl)dithiophosphinic acid (Cyanex-301). The synthesized Cyanex-301 coated SPION has been characterized by Transmission Electron Microscopy (TEM), Fourier-Transfer Infrared Spectroscopy (FT-IR), X-ray Photonic Spectroscopy (XPS), and Thermogravimetric Analysis (TGA). The adsorption mechanism was proposed to be via complexation between the thiol group on Cyanex-301 and Cr(VI) ions based on the XPS and FTIR analysis. It has been found that the equilibrium can be attained in less than 2 hr. The adsorption behavior of Cr(VI) on the Cyanex-301 coated SPION can be well described by the Langmuir model and the maximum adsorption capacity for Cr(VI) was estimated to be 30.8 mg/g. The selectivity of the Cyanex-301 coated SPION adsorbent towards Cr(VI) ions was found to be high and the maximum loading capacity obtained is up to an order of magnitude higher than that of other adsorbents reported in the literature. The desorption studies showed that more than 70% of Cr(VI) can be recovered using HNO3 as eluting solution. Our findings suggest a high potential of the designed adsorbent material for the treatment of industrial wastewater containing Cr(VI).

Shelf stability of nanofluids and its effect on thermal conductivity and viscosity

This study proposes a method and apparatus to estimate shelf stability of nanofluids. Nanofluids are fabricated by dispersion of solid nanoparticles in base fluids, and shelf stability is a key iss ...

Effect of Synthesis and Sintering Conditions on the Thermoelectric Properties of n-Doped Mg2Si

Magnesium silicide (Mg2Si)-based alloys are promising candidates for thermoelectric (TE) energy conversion in the middle–high temperature range. The detrimental effect of the presence of MgO on the TE properties of Mg2Si based materials is widely known. For this reason, the conditions used for synthesis and sintering were optimized to limit oxygen contamination. The effect of Bi doping on the TE performance of dense Mg2Si materials was also investigated. Synthesis was performed by ball milling in an inert atmosphere starting from commercial Mg2Si powder and Bi powder. The samples were consolidated, by spark plasma sintering, to a density >95%. The morphology, and the composition and crystal structure of samples were characterized by field-emission scanning electronic microscopy and x-ray diffraction, respectively. Moreover, determination of Seebeck coefficients and measurement of electrical and thermal conductivity were performed for all the samples. Mg2Si with 0.1 mol% Bi doping had a ZT value of 0.81, indicative of the potential of this method for fabrication of n-type bulk material with good TE performance.

Introduction of Metal Oxides into Mg2Si Thermoelectric Materials by Spark Plasma Sintering

Oxide incorporation into thermoelectric Mg2Si-based materials was performed starting from commercial Mg2Si and commercial metal oxides by applying ball milling and spark plasma sintering (SPS) processing. The SPS conditions, such as sintering temperature, pressure, and holding time, were optimized with the aim of obtaining both full densification and oxide incorporation. Thermoelectric characterizations, such as Seebeck coefficient and electrical and thermal conductivity, were carried out and related to the pellet compositions. The morphology, composition, and crystallographic structure of the samples were characterized by field-emission scanning electron microscopy, energy-dispersive spectrometry, and x-ray diffraction analyses, respectively.

ZnO-PLLA nanofiber nanocomposite for continuous flow mode purification of water from Cr(VI).

Nanomaterials of ZnO-PLLA nanofibers have been used for the adsorption of Cr(VI) as a prime step for the purification of water. The fabrication and application of the flexible ZnO-PLLA nanofiber nanocomposite as functional materials in this well-developed architecture have been achieved by growing ZnO nanorod arrays by chemical bath deposition on synthesized electrospun poly-L-lactide nanofibers. The nanocomposite material has been tested for the removal and regeneration of Cr(IV) in aqueous solution under a “continuous flow mode” by studying the effects of pH, contact time, and desorption steps. The adsorption of Cr(VI) species in solution was greatly dependent upon pH. SEM micrographs confirmed the successful fabrication of the ZnO-PLLA nanofiber nanocomposite. The adsorption and desorption of Cr(VI) species were more likely due to the electrostatic interaction between ZnO and Cr(VI) ions as a function of pH. The adsorption and desorption experiments utilizing the ZnO-PLLA nanofiber nanocomposite have appeared to be an effective nanocomposite in the removal and regeneration of Cr(VI) species.

On the electrical arc interruption by using PMMA/iron oxide nanocomposites

An experimental study is undertaken on the fabrication of poly (methyl methacrylate) (PMMA)/iron oxide nanocomposites to determine their potential use for electrical arc interruption in the electri ...

Chemical Synthesis of Iron Antimonide (FeSb2) and Its Thermoelectric Properties

Low temperature thermoelectric (TE) materials are in demand for more efficient cooling and power generation applications. Iron antimonide (FeSb2) draws great attention over the past few years because of its enhanced power factor values. Polycrystalline bulk FeSb2 nanopowder was prepared via a low-temperature molten salts approach followed by subsequent thermal treatment in synthetic air and hydrogen gas for calcination and reduction reactions, respectively. Structural analysis confirms the desired final phase with submicrometer grain size and high compaction density after consolidation using spark plasma sintering (SPS). TE transport properties revealed that the material is n-type below 150 K and p-type above this temperature; this suggests antimony vacancies in FeSb2. The electrical conductivity increased significantly, and the highest conductivity achieved was 6000 S/cm at 100 K. The maximum figure-of-merit, ZT, of 0.04 is achieved at 500 K, which is about 6 times higher than the earlier reported state-of-the art ZT value for the same material.

Fabrication and characterization of nanostructured thermoelectric FexCo1-xSb3

Abstract A novel synthesis route for the fabrication of p-type nanostructured skutterudite, FexCo1-xSb3 in large quantity is reported. This scalable synthesis route provides nano-engineered material with less impact on the environment compared to conventional synthesis procedures. Several Fe substituted compositions have been synthesized to confirm the feasibility of the process. The process consists of a nano-sized precursor fabrication of iron and cobalt oxalate, and antimony oxides by chemical co-precipitation. Further thermochemical processes result in the formation of iron substituted skutterudites. The nanopowders are compacted by Spark Plasma Sintering (SPS) technique in order to maintain nanostructure. Detailed physicochemical as well as thermoelectric transport properties are evaluated. Results reveal strongly reduced thermal conductivity values compared to conventionally prepared counterparts, due to nanostructuring. P-type characteristic was observed from the Seebeck measurements while electrical conductivity is high and shows metallic behavior. The highest TE figure of merit of 0.25 at 800 K has been achieved, which is strongly enhanced with respect to the mother compound CoSb3. This suggests the promise of the utilized method of fabrication and processing for TE applications with improved performance. Graphical Abstract