Monaheng L. Masheane

UV-assisted reduction of in situ electrospun antibacterial chitosan-based nanofibres for removal of bacteria from water

A greener synthesis of low-swelling uniformly-sized chitosan (CTS)-based nanofibres decorated with silver (Ag) and silver/iron (Ag/Fe) nanoparticles is reported. The synthesis was achieved by electrospinning a solution of CTS blended with varying amounts of polyacrylamide (PAA), polyethylene glycol (PEG) and Ag+ or Ag+/Fe3+ ions. These nanofibres were subjected to UV irradiation under ionised water vapour at low temperature (70 °C). The effect of UV irradiation time on the reduction of the NPs was confirmed using UV-Vis spectroscopy. The microstructure and chemical composition of the Ag and Ag/Fe modified nanofibres was studied using transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and ultraviolet-visible spectroscopy (UV-Vis). TEM revealed that the average diameter of the CTS-based nanofibres, AgNPs, and Ag/Fe NPs supported on the CTS-based nanofibres were 471 ± 89 nm, 18 ± 2.5 and 32 ± 8.7 nm respectively. XRD and EDS analysis confirmed the presence of Ag and Fe in the nanofibers. The biocidal effect of the Ag and Ag/Fe NPs supported on the CTS-based nanofibres was investigated using Gram positive (Bacillus cereus, Enterococcus faecalis) and Gram negative (Escherichia coli, Klebsiella pneumoniae, Klebsiella oxytoca, Pseudomonas aeruginosa, Proteus mirabilis, Shigella boydii, Shigella sonnei, Enterobacter cloacae) bacterial strains. The nanofibres exhibited a strong biocidal effect on the bacteria suggesting that they can be used as efficient antimicrobial materials in water systems that are contaminated by bacteria.

Thermally and mechanically stable β-cyclodextrin/cellulose acetate nanofibers synthesized using an environmentally benign procedure

ABSTRACT Electrospun cyclodextrin (CD)-based nanofibers with capabilities to remove pollutants from water have been synthesized and characterized. The high-quality nanofibers presented here were synthesized in two simple steps that involved in-situ electrospinning of the nanofibers and all nanocomponents, followed by the reduction of silver (Ag+) and iron (Fe3+) ions to nanoparticles using an environmentally benign process that involved irradiation of the electrospun fibers using a tailor-made UV-equipped furnace at low temperatures. In the previously reported study it was observed that Ag and Fe nanoparticles effectively removed a range of different strains of Gram-negative and Gram-positive bacteria from water. As such, this study focused on improving the thermal and mechanical properties of the nanofibers prepared from polymer blends of β-CDs with cellulose acetate (CA) and small additions (2 wt%) of functionalized multiwalled carbon nanotubes (f-MWCNTs). The electrospinning parameters were varied to determine the optimum conditions for preparation of uniform non-beaded nanofibers. Bead-free and uniform nanofibers were obtained at a polymer concentration of 32% at the ratio of 1:1 β-CDs:CA, syringe injection flow rate of 0.7 mL h−1, 15 cm between the tip of the spinneret and the collector, and a voltage of 16 kV. The addition of f-MWCNTs was found to improve the tensile strength of the nanofibers by twofold, relative to nanofibers with no f-MWCNTs. The thermal degradation of the nanofibers was improved by a magnitude of 50°C. The study has shown that adding small amounts of f-MWCNTs improved the thermal stability and mechanical strength of the CD/CA nanofibers significantly.

Environmentally benign chitosan-based nanofibres for potential use in water treatment

Abstract Chitosan (CS)-based nanocomposite materials are highly prone to swelling when in contact with water. It is therefore essential to modify them to enhance their resistance to swelling, in order to be applicable in water treatment. In this study, the CS-based nanofibres were prepared using the electrospinning technique. The nanofibres were prepared from a polymer blend of CS, and other polymers (polyacrylamide (PAA) and polyethylene glycol (PEG)) added in small optimized quantities to enhance the ability to electrospun CS. Elastic polyisoprene (PIP) and functionalized multi-walled carbon nanotubes (f-MWCNTs) were incorporated in the electrospinnable solution blend of CS, PAA and PEG to reduce the swelling behaviour of the CS-based nanofibres and to improve their mechanical strength and thermal properties. PIP did not only improve the morphology of the resulting nanofibres but also reduced their swelling behaviour by twofold. The addition of f-MWCNTs was found to improve the tensile strength of the nanofibres by twofold, relative to nanofibres with no f-MWCNTs. The thermal degradation of the nanofibres was improved by a magnitude of 50°C. Antibacterial silver (Ag) and iron (Fe) nanoparticles (NPs) were embedded on the nanofibres for their possible use in disinfection processes. These NPs have demonstrated a potential to kill bacteria in water and, therefore, the prepared nanofibres can be used in disinfection water treatment processes with reduced swelling capacity.

Antimicrobial Properties of Chitosan-Alumina/f-MWCNT Nanocomposites

Antimicrobial chitosan-alumina/functionalized-multiwalled carbon nanotube (f-MWCNT) nanocomposites were prepared by a simple phase inversion method. Scanning electron microscopy (SEM) analyses showed the change in the internal morphology of the composites and energy dispersive spectroscopy (EDS) confirmed the presence of alumina and f-MWCNTs in the chitosan polymer matrix. Fourier transform infrared (FTIR) spectroscopy showed the appearance of new functional groups from both alumina and f-MWCNTs, and thermogravimetric analysis (TGA) revealed that the addition of alumina and f-MWCNTs improved the thermal stability of the chitosan polymer. The presence of alumina and f-MWCNTs in the polymer matrix was found to improve the thermal stability and reduced the solubility of chitosan polymer. The prepared chitosan-alumina/f-MWCNT nanocomposites showed inhibition of twelve strains of bacterial strains that were tested. Thus, the nanocomposites show a potential for use as a biocide in water treatment for the removal of bacteria at different environmental conditions.

Chitosan-Based Nanocomposite Beads for Drinking Water Production

Potable drinking water is essential for the good health of humans and it is a critical feedstock in a variety of industries such as food and pharmaceutical industries. For the first time, chitosan-alumina/functionalised multiwalled carbon nanotube (f-MWCNT) nanocomposite beads were developed and investigated for the reduction of various physico-chemical parameters from water samples collected from open wells used for drinking purposes by a rural community in South Africa. The water samples were analysed before and after the reduction of the identified contaminants by the nanocomposite beads. The nanocomposite beads were effective in the removal of nitrate, chromium and other physico-chemical parameters. Although, the water samples contained these contaminants within the WHO and SANS241 limits for no risk, the long-term exposure and accumulation is an environmental and health concern. The reduction of these contaminants was dependent on pH levels. At lower pH, the reduction was significantly higher, up to 99.2% (SPC), 91.0% (DOC), 92.2% (DO), 92.2% (turbidity), 96.5% (nitrate) and 97.7% (chromium). Generally, the chitosan-alumina/f-MWCNT nanocomposite beads offer a promising alternative material for reduction and removal of various physico-chemical parameters for production portable water.

Carbon-supported photocatalysts for organic dye photodegradation

Abstract Textile industries are essential in the global economy. However, their failure to implement environmental regulations and comprehensive wastewater treatment has resulted to situations where unexhausted dye is discharged into natural streams without thorough treatment by some industries. Titanium dioxide has been widely used for photocatalytic decolorization of dyes. Its photoactivity in the UV-region of the electromagnetic spectrum has limited its commercial success in environmental depollution applications. This has necessitated the development of titania-based composites with superior efficiency. The use of carbon as a heterogeneous photocatalyst support is discussed in this chapter. A brief introduction to semiconductor-mediated advanced oxidation processes and the various approaches, both physical and chemical, for enhancing the efficacy of the photocatalyst is presented. The different allotropes of carbon are described in detail, and where appropriate, their application as photocatalyst supports used in the degradation of organic dyes. The techniques that have been employed in the synthesis and coupling of carbon to the photocatalyst are presented, where the physicochemical properties of carbon have been exploited to enhance the photocatalytic properties of titania. The synthesis methods employed highlight the shift by researchers toward facile, scalable and ultimately results that can be replicated at commercial level. The chapter ends with examples of photocatalysts supported on various carbon forms used in the decomposition of organic dyes.