Mônica Tirre de Souza Araújo

Bone mineral density

OBJECTIVE To verify whether bone mineral density (BMD) of cortical bone, trabecular bone, and total bone influence the primary stability of orthodontic miniscrews and to verify whether there is a correlation between the measurement of BMD by cone-beam computed tomography (CBCT) and central dual-energy x-ray absorptiometry (DEXA). MATERIALS AND METHODS Twenty bovine bone sections were extracted from the pubic and iliac bones from regions with cortical thicknesses of approximately 1 mm. The BMD of the total bone block was evaluated using two methods: CBCT and DEXA. The BMD of cortical, trabecular, and total bone in the region of interest (ROI) were also evaluated by CBCT. After scanning the bone blocks, 20 self-drilling miniscrews (INP®) 1.4 mm in diameter and 6 mm long were inserted into them. The peak implant insertion torque (IT) was registered. After this, the pull-out test (PS) was performed and the maximum force registered. The Pearson correlation test was applied to verify the correlations between variables. RESULTS The BMD of the total bone block verified by CBCT and DEXA showed a positive and strong correlation (r  =  0.866, P  =  .000). The BMD of the ROI for cortical bone influenced the IT (r  =  0.518, P  =  .40) and the PS of miniscrews (r  =  0.713, P  =  .001, Table 2). However, the total bone BMD (verified by CBCT and DEXA) and trabecular bone BMD presented weak and not statistically significant correlations with primary stability. CONCLUSIONS There was a positive correlation between total bone block BMD measured by DEXA and CBCT. The cortical BMD influenced the IT and PS.

Does rapid maxillary expansion have long-term effects on airway dimensions and breathing?

INTRODUCTION In this systematic review, we identified and qualified the evidence of long-term reports on the effects of rapid maxillary expansion (RME) on airway dimensions and functions. METHODS Electronic databases (Ovid, Scirus, Scopus, Virtual Health Library, and Cochrane Library) were searched from 1900 to September 2010. Clinical trials that assessed airway changes at least 6 months after RME in growing children with rhinomanometry, acoustic rhinometry, computed tomography, or posteroanterior and lateral radiographs were selected. Studies that used surgically assisted RME and evaluated other simultaneous treatments during expansion, systemically compromised subjects, or cleft patients were excluded. A methodologic-quality scoring process was used to identify which studies would be most valuable. RESULTS Fifteen articles fulfilled the inclusion criteria, and full texts were assessed. Three were excluded, and 12 were assessed for eligibility. Four articles with low methodologic quality were not considered. The remaining 8 were qualified as moderate. The posteroanterior radiographs showed that nasal cavity width increases; in the lateral radiographs, decreased craniocervical angulation was associated with increases of posterior nasal space. Cone-beam computed tomography did not show significant increases of nasal cavity volume. Rhinomanometry showed reduction of nasal airway resistance and increase of total nasal flow, and acoustic rhinometry detected increases of minimal cross-sectional area and nasal cavity volume. CONCLUSIONS There is moderate evidence that changes after RME in growing children improve the conditions for nasal breathing and the results can be expected to be stable for at least 11 months after therapy.

Effects of Two Low-Intensity Laser Therapy Protocols on Experimental Tooth Movement

OBJECTIVE The purpose of this in vivo study was to determine the effect of two low-intensity laser therapy (LILT) protocols on macroscopic and microscopic parameters of experimental tooth movement. MATERIALS AND METHODS To induce experimental tooth movement in rats, 40 cN of orthodontic force was applied to the left first molars. Next, a gallium-aluminum-arsenide (Ga-Al-As) diode laser with a wavelength of 830 nm and power output of 100 mW was applied with fluence of 6000 J/cm(2) on the area around the moved tooth. Two different application protocols were used in the experimental groups: one with daily irradiation and another with irradiation during early stages. Macroscopic and microscopic analyses were performed at days 2 and 7 of tooth movement. The amount of tooth movement was measured with a caliper, and tartrate-resistant acid phosphatase and picrosirius staining were used to enable identification of osteoclasts and immature collagen, respectively. RESULTS The amount of tooth movement did not differ between the irradiated and nonirradiated groups on days 2 and 7 of the experiment. On day 2, no difference was observed in the number of osteoclasts or the percentage of immature collagen. On day 7, there was an increase in the number of osteoclasts after daily applications of LILT, while two applications produced no significant difference from control. The amount of immature collagen on the tension side significantly increased in the nonirradiated group and when LILT was applied for only 2 d, whereas it was shown to be inhibited by daily LILT applications (p < 0.05). CONCLUSION The tested LILT protocols were unable to accelerate tooth movement. Even though the number of osteoclasts increased when LILT was applied daily, the repair at the tension zone was inhibited.

Is miniscrew primary stability influenced by bone density

Primary stability is absence of mobility in the bone bed after mini-implant placement and depends on bone quality among other factors. Bone quality is a subjective term frequently considered as bone density. The aim of this preliminary study was to evaluate bone density in two bovine pelvic regions and verify the primary stability of miniscrews inserted into them. Forty bone blocks were extracted from bovine pelvic bones, 20 from iliac and 20 from pubic bone, all of them containing cortical bone about 1 mm thick. Half of the sections extracted from each bone were designated for histological evaluation of bone density (trabecular bone area - TBA) and the other half for bone mineral density (BMD) evaluation by means of central dual-energy X-ray absorptiometry (DEXA). Then, twenty self-drilling miniscrews (INP®, São Paulo, Brazil) 1.4 mm in diameter and 6 mm long were inserted into the bone blocks used for BMD evaluation. Peak implant insertion torque (IT) and pull-out strength (PS) were used for primary stability evaluation. It was found that iliac and pubic bones present different bone densities, iliac bone being less dense considering BMD and TBA values (P > 0.05). However, the miniscrew primary stability was not different when varying the bone type (P < 0.05). IT and PS were not influenced by these differences in bone density when cortical thickness was about 1 mm thick.

Mechanical testing and finite element analysis of orthodontic teardrop loop

INTRODUCTION Understanding how teeth move in response to mechanical loads is an important aspect of orthodontic treatment. Treatment planning should include consideration of the appliances that will meet the desired loading of the teeth to result in optimized treatment outcomes. The purpose of this study was to evaluate the use of computer simulation to predict the force and the torsion obtained after the activation of tear drop loops of 3 heights. METHODS Seventy-five retraction loops were divided into 3 groups according to height (6, 7, and 8 mm). The loops were subjected to tensile load through displacements of 0.5, 1.0, 1.5, and 2.0 mm, and the resulting forces and torques were recorded. The loops were designed in AutoCAD software(2005; Autodesk Systems, Alpharetta, GA), and finite element analysis was performed with Ansys software(version 7.0; Swanson Analysis System, Canonsburg, PA). Statistical analysis of the mechanical experiment results was obtained by ANOVA and the Tukey post-hoc test (P < .01). The correlation test and the paired t test (P < .05) were used to compare the computer simulation with the mechanical experiment. RESULTS AND CONCLUSIONS The computer simulation accurately predicted the experimentally determined mechanical behavior of tear drop loops of different heights and should be considered an alternative for designing orthodontic appliances before treatment.

Long-term fluoride release from resin-reinforced orthodontic cements following recharge with fluoride solution

The aim of this study was to test the hypothesis that there is no difference in the fluoride release behavior of resin-reinforced glass ionomer cements before or after fluoride recharge. The materials were divided into 5 groups: 2 resin-reinforced glass ionomer cements used for attaching orthodontic bands, that is, group FOB (Fuji Ortho Band) and group MCB (Multi-Cure Glass Ionomer Orthodontic Band Cement); 2 resin-reinforced glass ionomer cements and a composite used for bonding orthodontic brackets, that is, group OGLC (Ortho Glass LC), group FOLC (Fuji Ortho LC), and group TXT (Transbond XT), respectively. Fluoride release was measured during a 60-day period by using selective ion electrodes connected to an ionic analyser. After 4 weeks, the samples were exposed to 0.221% sodium fluoride solution. The results showed that cements achieved a maximum fluoride release 24 h after initial setting. No statistically significant differences were observed between groups FOB and OGLC regarding the amount of released fluoride following fluoride recharge from day 31 to day 36 (p>0.05). In conclusion, FOB and OGLC cements showed a higher capacity of capturing and releasing fluoride compared to the other cements studied.

Root damage associated with intermaxillary screws: a systematic review

This systematic review examined the literature for evidence of dental root damage after contact with intermaxillary screws (IMS). Electronic databases, including the Cochrane Library, Ovid, Scirus, Scopus and Virtual Health Library, were used to search for original articles from 1980 to January 2011. Prospective and retrospective studies that assessed the association of root damage and contact with IMS were selected. Two authors independently reviewed and extracted the data from the included studies. A methodological quality scoring process was used to classify whether the articles presented low, moderate or high evidence. The search retrieved 795 citations. Nine studies fulfilled the initial selection criteria. Of these studies, 3 were excluded. Two studies did not note any iatrogenic injuries of the dental roots; the other study was a case report. Of the 6 included articles, 2 were ranked as having low and four as having moderate evidence. The moderate evidence found suggested that the roots did not exhibit clinical changes after coming into contact with the IMS, but this situation depends on the root damage level. To obtain reliable scientific evidence, studies with an adequate sample size and diagnostic methods are required to confirm the effects of IMS on the dental root.

Combined maxillary and mandibular distraction osteogenesis in patients with hemifacial microsomia

INTRODUCTION Hemifacial microsomia is a deformity of variable expressivity with unilateral hypoplasia of the mandible and the ear. In this study, we evaluated skeletal soft tissue changes after bimaxillary unilateral vertical distraction. METHODS Eight patients (4 preadolescents 4 adolescents) each with a grade II mandibular deformity underwent a LeFort I osteotomy and an ipsilateral horizontal mandibular ramus osteotomy. A semiburied distraction device was placed over the ramus, and intermaxillary fixation was applied. Anteroposterior cephalometric and frontal photographic analyses were conducted before and after distraction. Statistics were used to analyze the preoperative and postoperative changes. RESULTS Cephalometrically, the nasal floor and the occlusal and gonial plane angles decreased. The ratios of affected-unaffected ramus and gonial angle heights improved by 15% and 20%, respectively. The position of menton moved toward the midline. The photographic analysis showed a decrease of the nasal and commissure plane angles, and the chin moved to the unaffected side. The parallelism between the horizontal skeletal and soft tissue planes improved, with an increase in the affected side ramus height and correction of the chin point toward the midline. CONCLUSIONS Simultaneous maxillary and mandibular distraction improved facial balance and symmetry. Patients in the permanent dentition with fixed orthodontic appliances and well-aligned dental arches responded well to this intervention.

Root repair after contact with mini-implants: systematic review of the literature

This systematic review identified and qualified the current evidence of dental root damage and repair after contact with mini-implants. The electronic databases Cochrane library, Ovid, Scirus, Scopus, and Virtual Health Library were used to search original articles from 1980 to December 2011. The inclusion criteria to select the articles were 1. randomized controlled trials and prospective clinical studies based on trials involving humans, 2. randomized controlled studies in animals, 3. use of mini-implants with a diameter less than 2.5 mm, and 4. root contact evaluation associated with the use of orthodontic mini-implants. Two authors independently reviewed and extracted data from the selected studies and a methodological quality assessment process was used to rank the studies classifying them as low moderate or high quality. The searches retrieved 579 citations. After initial selection, 17 studies were considered eligible and their full texts were assessed. Four of those were excluded because root damage was not evaluated and two were excluded because of overlapping samples. Eleven articles, nine in animals and two in humans, fulfilled the inclusion criteria. From these, two studies were ranked as presenting high methodological quality, eight were judged to be of moderate, and one of low quality. The evidence found suggested that the quality of root repair depends on the amount of damage caused by the mini-implant. When the damage is limited to the cementum or dentin, healing and almost complete and repair of the periodontal structure can occur. Mini-implants that injured the pulp were less likely to result in complete repair of the periodontal tissues.

Orthodontic correction of a maxillary canine-first premolar transposition.

Transposition is a form of ectopia, in which 2 adjacent teeth change positions in the dental arch or 1 tooth develops in a position occupied by a nonadjacent tooth. Transposition can be partial or complete. Despite their low prevalence in the general population, transpositions are a challenge to orthodontists, especially if treatment aims to correct the order of the teeth. This article reports the diagnosis, planning, and treatment of a unilateral maxillary canine-first premolar transposition in a female patient treated orthodontically without premolar extraction and with correction of the transposition. Treatment options, advantages and disadvantages of each method, and the mechanics used during the treatment are also discussed.