Monika Österberg

Nanoscale Cellulose Films with Different Crystallinities and Mesostructures—Their Surface Properties and Interaction with Water

A systematic study of the degree of molecular ordering and swelling of different nanocellulose model films has been conducted. Crystalline cellulose II surfaces were prepared by spin-coating of the precursor cellulose solutions onto oxidized silicon wafers before regeneration in water or by using the Langmuir-Schaefer (LS) technique. Amorphous cellulose films were also prepared by spin-coating of a precursor cellulose solution onto oxidized silicon wafers. Crystalline cellulose I surfaces were prepared by spin-coating wafers with aqueous suspensions of sulfate-stabilized cellulose I nanocrystals and low-charged microfibrillated cellulose (LC-MFC). In addition, a dispersion of high-charged MFC was used for the buildup of polyelectrolyte multilayers with polyetheyleneimine on silica with the aid of the layer-by-layer (LbL) technique. These preparation methods produced smooth thin films on the nanometer scale suitable for X-ray diffraction and swelling measurements. The surface morphology and thickness of the cellulose films were characterized in detail by atomic force microscopy (AFM) and ellipsometry measurements, respectively. To determine the surface energy of the cellulose surfaces, that is, their ability to engage in different interactions with different materials, they were characterized through contact angle measurements against water, glycerol, and methylene iodide. Small incidence angle X-ray diffraction revealed that the nanocrystal and MFC films exhibited a cellulose I crystal structure and that the films prepared from N-methylmorpholine-N-oxide (NMMO), LiCl/DMAc solutions, using the LS technique, possessed a cellulose II structure. The degree of crystalline ordering was highest in the nanocrystal films (approximately 87%), whereas the MFC, NMMO, and LS films exhibited a degree of crystallinity of about 60%. The N,N-dimethylacetamide (DMAc)/LiCl film possessed very low crystalline ordering (<15%). It was also established that the films had different mesostructures, that is, structures around 10 nm, depending on the preparation conditions. The LS and LiCl/DMAc films are smooth without any clear mesostructure, whereas the other films have a clear mesostructure in which the dimensions are dependent on the size of the nanocrystals, fibrillar cellulose, and electrostatic charge of the MFC. The swelling of the films was studied using a quartz crystal microbalance with dissipation. To understand the swelling properties of the films, it was necessary to consider both the difference in crystalline ordering and the difference in mesostructure of the films.

Poly(N-isopropylacrylamide) Brushes Grafted from Cellulose Nanocrystals via Surface-Initiated Single-Electron Transfer Living Radical Polymerization

Cellulose nanocrystals (CNCs) or nanowhiskers produced from sulfuric acid hydrolysis of ramie fibers were used as substrates for surface chemical functionalization with thermoresponsive macromolecules. The CNCs were grafted with poly(N-isopropylacrylamide) brushes via surface-initiated single-electron transfer living radical polymerization (SI-SET-LRP) under various conditions at room temperature. The grafting process was confirmed via Fourier transform IR spectroscopy and X-ray photoelectron spectroscopy and the different molecular masses of the grafts were quantified and found to depend on the initiator and monomer concentrations used. No observable damage occurred to the CNCs after grafting, as determined by X-ray diffraction. Size exclusion chromatography analyses of polymer chains cleaved from the cellulose nanocrystals indicated that a higher degree of polymerization was achieved by increasing initiator or monomer loading, most likely caused by local heterogeneities yielding higher rates of polymerization. It is expected that suspension stability, interfacial interactions, friction, and other properties of grafted CNCs can be controlled by changes in temperature and provide a unique platform for further development of stimuli-responsive nanomaterials.

Model Films from Native Cellulose Nanofibrils. Preparation, Swelling, and Surface Interactions

Native cellulose model films containing both amorphous and crystalline cellulose I regions were prepared by spin-coating aqueous cellulose nanofibril dispersions onto silica substrates. Nanofibrils from wood pulp with low and high charge density were used to prepare the model films. Because the low charged nanofibrils did not fully cover the silica substrates, an anchoring substance was selected to improve the coverage. The model surfaces were characterized using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The effect of nanofibril charge density, electrolyte concentration, and pH on swelling and surface interactions of the model film was studied by quartz crystal microbalance with dissipation (QCM-D) and AFM force measurements. The results showed that the best coverage for the low charged fibrils was achieved by using 3-aminopropyltrimethoxysilane (APTS) as an anchoring substance and hence it was chosen as the anchor. The AFM and XPS measurements showed that the fibrils are covering the substrates. Charge density of the fibrils affected the morphology of the model surfaces. The low charged fibrils formed a network structure while the highly charged fibrils formed denser film structure. The average thickness of the films corresponded to a monolayer of fibrils, and the average rms roughness of the films was 4 and 2 nm for the low and high charged nanofibril films, respectively. The model surfaces were stable in QCM-D swelling experiments, and the behavior of the nanofibril surfaces at different electrolyte concentrations and pHs correlated with other studies and the theories of Donnan. The AFM force measurements with the model surfaces showed well reproducible results, and the swelling results correlated with the swelling observed by QCM-D. Both steric and electrostatic forces were observed and the influence of steric forces increased as the films were swelling due to changes in pH and electrolyte concentration. These films differ from previous model cellulose films due to their chemical composition (crystalline cellulose I and amorphous regions) and fibrillar structure and hence serve as excellent models for the pulp fiber surface.

A Fast Method to Produce Strong NFC Films as a Platform for Barrier and Functional Materials

In this study, we present a rapid method to prepare robust, solvent-resistant, nanofibrillated cellulose (NFC) films that can be further surface-modified for functionality. The oxygen, water vapor, and grease barrier properties of the films were measured, and in addition, mechanical properties in the dry and wet state and solvent resistance were evaluated. The pure unmodified NFC films were good barriers for oxygen gas and grease. At a relative humidity below 65%, oxygen permeability of the pure and unmodified NFC films was below 0.6 cm(3) μm m(-2) d(-1) kPa(-1), and no grease penetrated the film. However, the largest advantage of these films was their resistance to various solvents, such as water, methanol, toluene, and dimethylacetamide. Although they absorbed a substantial amount of solvent, the films could still be handled after 24 h of solvent soaking. Hot-pressing was introduced as a convenient method to not only increase the drying speed of the films but also enhance the robustness of the films. The wet strength of the films increased due to the pressing. Thus, they can be chemically or physically modified through adsorption or direct chemical reaction in both aqueous and organic solvents. Through these modifications, the properties of the film can be enhanced, introducing, for example, functionality, hydrophobicity, or bioactivity. Herein, a simple method using surface coating with wax to improve hydrophobicity and oxygen barrier properties at very high humidity is described. Through this modification, the oxygen permeability decreased further and was below 17 cm(3) μm m(-2) d(-1) kPa(-1) even at 97.4% RH, and the water vapor transmission rate decreased from 600 to 40 g/m(2) day. The wax treatment did not deteriorate the dry strength of the film. Possible reasons for the unique properties are discussed. The developed robust NFC films can be used as a generic, environmentally sustainable platform for functional materials.

Enzymatic Hydrolysis of Native Cellulose Nanofibrils and Other Cellulose Model Films: Effect of Surface Structure

Model films of native cellulose nanofibrils, which contain both crystalline cellulose I and amorphous domains, were used to investigate the dynamics and activities of cellulase enzymes. The enzyme binding and degradation of nanofibril films were compared with those for other films of cellulose, namely, Langmuir-Schaefer and spin-coated regenerated cellulose, as well as cellulose nanocrystal cast films. Quartz crystal microbalance with dissipation (QCM-D) was used to monitor the changes in frequency and energy dissipation during incubation at varying enzyme concentrations and experimental temperatures. Structural and morphological changes of the cellulose films upon incubation with enzymes were evaluated by using atomic force microscopy. The QCM-D results revealed that the rate of enzymatic degradation of the nanofibril films was much faster compared to the other types of cellulosic films. Higher enzyme loads did not dramatically increase the already fast degradation rate. Real-time measurements of the coupled contributions of enzyme binding and hydrolytic reactions were fitted to an empirical model that closely described the cellulase activities. The hydrolytic potential of the cellulase mixture was found to be considerably affected by the nature of the substrates, especially their crystallinity and morphology. The implications of these observations are discussed in this report.

Surface chemistry and morphology of different mechanical pulps determined by ESCA and AFM

The surface chemistry and morphology of spruce (Picea abies) mechanical pulps have been investigated by Electron spectroscopy for chemical analysis (ESCA) and Atomic force microscopy (AFM). As determined by ESCA, the content of lignin was slightly higher on the pulp surface than in the whole pulp. The surface coverage by lignin remained approximately the same after peroxide and dithionite bleaching, whereas on the ozone treated pressure groundwood (PGW) pulp the amount of lignin was strongly reduced. The AFM studies showed that the surfaces of mechanical pulp fibres are very heterogeneous, i.e. different cell wall layers are exposed along the fibre surface. It was found that the surfaces of unbleached PGW and thermomechanical pulp (TMP) fibres consist of both granular and fibrillar structures, whereas the surfaces of unbleached chemithermomechanical pulp (CTMP) fibres are almost fully covered by granular material. This granular layer, which is interpreted to originate from the middle lamella and the primary wall, was removed from the CTMP fibre surface after peroxide bleaching, exposing the underlying structure. However, the surface coverage by lignin determined by ESCA was not reduced. This suggests that peroxide bleaching of sulphonated CTMP pulp in some way modifies the lignin and pectin rich surface and that lignin occurs also in a non-granular form on the surface of mechanical pulps. Peroxide or dithionite bleaching had no effect on the morphology of PGW and TMP fibres. The highest amounts of extractives were found on unwashed and unbleached TMP pulp. It turned out that only part of the extractives was removed from the surface by alkaline treatment and by peroxide bleaching.

Surface Functionalized Nanofibrillar Cellulose (NFC) Film as a Platform for Immunoassays and Diagnostics

We introduce a new method to modify films of nanofibrillated cellulose (NFC) to produce non-porous, water-resistant substrates for diagnostics. First, water resistant NFC films were prepared from mechanically disintegrated NFC hydrogel, and then their surfaces were carboxylated via TEMPO-mediated oxidation. Next, the topologically functionalized film was activated via EDS/NHS chemistry, and its reactivity verified with bovine serum albumin and antihuman IgG. The surface carboxylation, EDC/NHS activation and the protein attachment were confirmed using quartz crystal microbalance with dissipation, contact angle measurements, conductometric titrations, X-ray photoelectron spectroscopy and fluorescence microscopy. The surface morphology of the prepared films was investigated using confocal laser scanning microscopy and atomic force microscopy. Finally, we demonstrate that antihuman IgG can be immobilized on the activated NFC surface using commercial piezoelectric inkjet printing.

Functionalization of Nanofibrillated Cellulose with Silver Nanoclusters: Fluorescence and Antibacterial Activity

Native cellulose nanofibers are functionalized using luminescent metal nanoclusters to form a novel type of functional nanocellulose/nanocluster composite. Previously, various types of cellulose fibers have been functionalized with large, non-luminescent metal nanoparticles. Here, mechanically strong native cellulose nanofibers, also called nanofibrillatedcellulose (NFC), microfibrillatedcellulose (MFC) ornanocellulose, disintegrated from macroscopic cellulose pulp fibers are used as support for small and fluorescent silver nanoclusters. The functionalization occurs in a supramolecular manner, mediated by poly(methacrylic acid) that protects nanoclusters while it allows hydrogen bonding with cellulose, leading to composites with fluorescence and antibacterial activity.

A simple process for lignin nanoparticle preparation

A lack of renewable resources and their inefficient use is a major challenge facing the society. Lignin is a natural biopolymer obtained mainly as a by-product from the pulp- and paper-making industries, and is primarily burned to produce energy. However, interest for using lignin in more advanced applications has increased rapidly. In particular, lignin based nanoparticles could find potential use in functional surface coatings, nanoglue, drug delivery, and microfluidic devices. In this work, a straightforward method to produce lignin nanoparticles from waste lignin obtained from kraft pulping is introduced. Spherical lignin nanoparticles were obtained by dissolving softwood kraft lignin in tetrahydrofuran (THF) and subsequently introducing water into the system through dialysis. No chemical modification of lignin was needed. Water acts as a non-solvent reducing lignins degrees of freedom causing the segregation of hydrophobic regions to compartments within the forming nanoparticles. The final size of the nanoparticles depended on the pre-dialysis concentration of dissolved lignin. The stability of the nanoparticle dispersion as a function of time, salt concentration and pH was studied. In pure water and at room temperature the lignin nanoparticle dispersion was stable for over two months, but a very low pH or high salt concentration induced aggregation. It was further demonstrated that the surface charge of the particles could be reversed and stable cationic lignin nanoparticles were produced by adsorption of poly(diallyldimethylammonium chloride) (PDADMAC).

Colloidal Ionic Assembly between Anionic Native Cellulose Nanofibrils and Cationic Block Copolymer Micelles into Biomimetic Nanocomposites

We present a facile ionic assembly between fibrillar and spherical colloidal objects toward biomimetic nanocomposites with majority hard and minority soft domains based on anionic reinforcing native cellulose nanofibrils and cationic amphiphilic block copolymer micelles with rubbery core. The concept is based on ionic complexation of carboxymethylated nanofibrillated cellulose (NFC, or also denoted as microfibrillated cellulose, MFC) and micelles formed by aqueous self-assembly of quaternized poly(1,2-butadiene)-block-poly(dimethylaminoethyl methacrylate) with high fraction of the NFC reinforcement. The adsorption of block copolymer micelles onto nanocellulose is shown by quartz crystal microbalance measurements, atomic force microscopy imaging, and fluorescent optical microscopy. The physical properties are elucidated using electron microscopy, thermal analysis, and mechanical testing. The cationic part of the block copolymer serves as a binder to NFC, whereas the hydrophobic rubbery micellar cores are designed to facilitate energy dissipation and nanoscale lubrication between the NFC domains under deformation. We show that the mechanical properties do not follow the rule of mixtures, and synergistic effects are observed with promoted work of fracture in one composition. As the concept allows wide possibilities for tuning, the work suggests pathways for nanocellulose-based biomimetic nanocomposites combining high toughness with stiffness and strength.