Moulay Tahar Sougrati

Better Cycling Performances of Bulk Sb in Na-Ion Batteries Compared to Li-Ion Systems: An Unexpected Electrochemical Mechanism

Pure micrometric antimony can be successfully used as negative electrode material in Na-ion batteries, sustaining a capacity close to 600 mAh g(-1) at a high rate with a Coulombic efficiency of 99 over 160 cycles, an extremely high capacity compared to any other compound tested against both Li and Na. The reaction mechanism with Na does not simply go through the alloying mechanism observed for Li where the intermediate species are those expected from the phase diagram. In the case of Na, the intermediate phases are mostly amorphous and could not be precisely identified. Surprisingly, we evidenced that a competition takes place at the end of the discharge of the Sb/Na cell between the formation of the hexagonal and the cubic polymorphs of Na(3)Sb, the last being described in the literature as unstable at atmospheric pressure and only synthesized under high pressure (1-9 GPa). In addition, fluoroethylene carbonate added to the electrolyte combined with an appropriate electrode formulation based on carboxymethyl cellulose, carbon black, and vapor ground carbon fibers seems to be determinant in the excellent performances of this material.

Identification of catalytic sites for oxygen reduction in iron- and nitrogen-doped graphene materials

While platinum has hitherto been the element of choice for catalysing oxygen electroreduction in acidic polymer fuel cells, tremendous progress has been reported for pyrolysed Fe-N-C materials. However, the structure of their active sites has remained elusive, delaying further advance. Here, we synthesized Fe-N-C materials quasi-free of crystallographic iron structures after argon or ammonia pyrolysis. These materials exhibit nearly identical Mössbauer spectra and identical X-ray absorption near-edge spectroscopy (XANES) spectra, revealing the same Fe-centred moieties. However, the much higher activity and basicity of NH3-pyrolysed Fe-N-C materials demonstrates that the turnover frequency of Fe-centred moieties depends on the physico-chemical properties of the support. Following a thorough XANES analysis, the detailed structures of two FeN4 porphyrinic architectures with different O2 adsorption modes were then identified. These porphyrinic moieties are not easily integrated in graphene sheets, in contrast with Fe-centred moieties assumed hitherto for pyrolysed Fe-N-C materials. These new insights open the path to bottom-up synthesis approaches and studies on site-support interactions.

Reversible anionic redox chemistry in high-capacity layered-oxide electrodes

Li-ion batteries have contributed to the commercial success of portable electronics and may soon dominate the electric transportation market provided that major scientific advances including new materials and concepts are developed. Classical positive electrodes for Li-ion technology operate mainly through an insertion-deinsertion redox process involving cationic species. However, this mechanism is insufficient to account for the high capacities exhibited by the new generation of Li-rich (Li(1+x)Ni(y)Co(z)Mn(1-x-y-z)O₂) layered oxides that present unusual Li reactivity. In an attempt to overcome both the inherent composition and the structural complexity of this class of oxides, we have designed structurally related Li₂Ru(1-y)Sn(y)O₃ materials that have a single redox cation and exhibit sustainable reversible capacities as high as 230 mA h g(-1). Moreover, they present good cycling behaviour with no signs of voltage decay and a small irreversible capacity. We also unambiguously show, on the basis of an arsenal of characterization techniques, that the reactivity of these high-capacity materials towards Li entails cumulative cationic (M(n+)→M((n+1)+)) and anionic (O(2-)→O₂(2-)) reversible redox processes, owing to the d-sp hybridization associated with a reductive coupling mechanism. Because Li₂MO₃ is a large family of compounds, this study opens the door to the exploration of a vast number of high-capacity materials.

Highly active oxygen reduction non-platinum group metal electrocatalyst without direct metal-nitrogen coordination.

Replacement of noble metals in catalysts for cathodic oxygen reduction reaction with transition metals mostly create active sites based on a composite of nitrogen-coordinated transition metal in close concert with non-nitrogen-coordinated carbon-embedded metal atom clusters. Here we report a non-platinum group metal electrocatalyst with an active site devoid of any direct nitrogen coordination to iron that outperforms the benchmark platinum-based catalyst in alkaline media and is comparable to its best contemporaries in acidic media. In situ X-ray absorption spectroscopy in conjunction with ex situ microscopy clearly shows nitrided carbon fibres with embedded iron particles that are not directly involved in the oxygen reduction pathway. Instead, the reaction occurs primarily on the carbon–nitrogen structure in the outer skin of the nitrided carbon fibres. Implications include the potential of creating greater active site density and the potential elimination of any Fenton-type process involving exposed iron ions culminating in peroxide initiated free-radical formation.

A 3.90 V iron-based fluorosulphate material for lithium-ion batteries crystallizing in the triplite structure

Li-ion batteries have empowered consumer electronics and are now seen as the best choice to propel forward the development of eco-friendly (hybrid) electric vehicles. To enhance the energy density, an intensive search has been made for new polyanionic compounds that have a higher potential for the Fe²⁺/Fe³⁺ redox couple. Herein we push this potential to 3.90 V in a new polyanionic material that crystallizes in the triplite structure by substituting as little as 5 atomic per cent of Mn for Fe in Li(Fe(1-δ)Mn(δ))SO₄F. Not only is this the highest voltage reported so far for the Fe²⁺/Fe³⁺ redox couple, exceeding that of LiFePO₄ by 450 mV, but this new triplite phase is capable of reversibly releasing and reinserting 0.7-0.8 Li ions with a volume change of 0.6% (compared with 7 and 10% for LiFePO₄ and LiFeSO₄F respectively), to give a capacity of ~125 mA h g⁻¹.

Slow Magnetic Relaxation in a Family of Trigonal Pyramidal Iron(II) Pyrrolide Complexes

We present a family of trigonal pyramidal iron(II) complexes supported by tris(pyrrolyl-α-methyl)amine ligands of the general formula [M(solv)(n)][(tpa(R))Fe] (M = Na, R = tert-butyl (1), phenyl (4); M = K, R = mesityl (2), 2,4,6-triisopropylphenyl (3), 2,6-difluorophenyl (5)) and their characterization by X-ray crystallography, Mössbauer spectroscopy, and high-field EPR spectroscopy. Expanding on the discovery of slow magnetic relaxation in the recently reported mesityl derivative 2, this homologous series of high-spin iron(II) complexes enables an initial probe of how the ligand field influences the static and dynamic magnetic behavior. Magnetization experiments reveal large, uniaxial zero-field splitting parameters of D = -48, -44, -30, -26, and -6.2 cm(-1) for 1-5, respectively, demonstrating that the strength of axial magnetic anisotropy scales with increasing ligand field strength at the iron(II) center. In the case of 2,6-difluorophenyl substituted 5, high-field EPR experiments provide an independent determination of the zero-field splitting parameter (D = -4.397(9) cm(-1)) that is in reasonable agreement with that obtained from fits to magnetization data. Ac magnetic susceptibility measurements indicate field-dependent, thermally activated spin reversal barriers in complexes 1, 2, and 4 of U(eff) = 65, 42, and 25 cm(-1), respectively, with the barrier of 1 constituting the highest relaxation barrier yet observed for a mononuclear transition metal complex. In addition, in the case of 1, the large range of temperatures in which slow relaxation is observed has enabled us to fit the entire Arrhenius curve simultaneously to three distinct relaxation processes. Finally, zero-field Mössbauer spectra collected for 1 and 4 also reveal the presence of slow magnetic relaxation, with two independent relaxation barriers in 4 corresponding to the barrier obtained from ac susceptibility data and to the 3D energy gap between the M(S) = ±2 and ±1 levels, respectively.

Understanding the roles of anionic redox and oxygen release during electrochemical cycling of lithium-rich layered Li4FeSbO6.

Li-rich oxides continue to be of immense interest as potential next generation Li-ion battery positive electrodes, and yet the role of oxygen during cycling is still poorly understood. Here, the complex electrochemical behavior of Li4FeSbO6 materials is studied thoroughly with a variety of methods. Herein, we show that oxygen release occurs at a distinct voltage plateau from the peroxo/superoxo formation making this material ideal for revealing new aspects of oxygen redox processes in Li-rich oxides. Moreover, we directly demonstrate the limited reversibility of the oxygenated species (O2(n-); n = 1, 2, 3) for the first time. We also find that during charge to 4.2 V iron is oxidized from +3 to an unusual +4 state with the concomitant formation of oxygenated species. Upon further charge to 5.0 V, an oxygen release process associated with the reduction of iron +4 to +3 is present, indicative of the reductive coupling mechanism between oxygen and metals previously reported. Thus, in full state of charge, lithium removal is fully compensated by oxygen only, as the iron and antimony are both very close to their pristine states. Besides, this charging step results in complex phase transformations that are ultimately destructive to the crystallinity of the material. Such findings again demonstrate the vital importance of fully understanding the behavior of oxygen in such systems. The consequences of these new aspects of the electrochemical behavior of lithium-rich oxides are discussed in detail.

Design of new electrode materials for Li-ion and Na-ion batteries from the bloedite mineral Na2Mg(SO4)2·4H2O

Mineralogy offers a large database to search for Li- or Na-based compounds having suitable structural features for acting as electrode materials, LiFePO4 being one example. Here we further explore this avenue and report on the electrochemical properties of the bloedite type compounds Na2M(SO4)2·4H2O (M = Mg, Fe, Co, Ni, Zn) and their dehydrated phases Na2M(SO4)2 (M = Fe, Co), whose structures have been solved via complementary synchrotron X-ray diffraction, neutron powder diffraction and transmission electron microscopy. Among these compounds, the hydrated and anhydrous iron-based phases show electrochemical activity with the reversible release/uptake of 1 Na+ or 1 Li+ at high voltages of ∼3.3 V vs. Na+/Na0 and ∼3.6 V vs. Li+/Li0, respectively. Although the reversible capacities remain lower than 100 mA h g−1, we hope this work will stress further the importance of mineralogy as a source of inspiration for designing eco-efficient electrode materials.

Fluorosulfate Positive Electrodes for Li-Ion Batteries Made via a Solid-State Dry Process.

Ionothermal synthesis has recently been used to prepare a fluorosulfate (LiFeSO 4 F) capable of reversibly intercalating Li at 3.6 V vs Li, making this material a serious contender to LiFePO 4 for HEV and electric vehicle applications. Although fluorosulfates are made from low cost and abundant starting materials, their synthesis is costly because of the use of ionic liquids as synthetic medium. Herein, we report a solid-state process by which LiFeSO 4 F can be synthesized without the use of ionic liquids but at the expense of both longer reaction time and weakly contaminated samples. Additionally, we show how powerful Mossbauer spectroscopy can be in the optimization of the various stages of electrode preparation as shown through the synthesis of LiFeSO 4 F and its implementation into an electrode. The importance of having Fe 3+ -free hydrated precursors to routinely obtain pure LiFeSO 4 F samples is shown together with the need to optimize ballmilling conditions to preserve Fe 3+ -free LiFeSO 4 F composites. Samples prepared via this low temperature solid-state process show battery performances approaching those of samples prepared using ionic liquids as synthetic medium. Furthermore, this process can be extended to the synthesis of the other members of the fluorosulfates AMSO 4 F family with A = Li, Na and M = Fe, Co, and Ni.

Room-Temperature Synthesis of Iron-Doped Anatase TiO2 for Lithium-Ion Batteries and Photocatalysis

Iron-doped nanocrystalline particles of anatase TiO2 (denoted x% Fe-TiO2, with x the nominal [Fe] atom % in solution) have been successfully synthesized at room temperature by a controlled two-step process. Hydrolysis of titanium isopropoxide is first achieved to precipitate Ti(OH)4 species. A fine control of the pH allows one to maintain (i) soluble iron species and (ii) a sluggish solubility of Ti(OH)4 to promote a dissolution and condensation of titanium clusters incorporating iron, leading to the precipitation of iron-doped anatase TiO2. The pH does then influence both the nature and crystallinity of the final phase. After 2 months of aging at pH = 2, well-dispersed nanocrystalline iron-doped TiO2 particles have been achieved, leading to 5-6 nm particle size and offering a high surface area of ca. 280 m(2)/g. This dissolution/recrystallization process allows the incorporation of a dopant concentration of up to 7.7 atom %; the successful incorporation of iron in the structure is demonstrated by X-ray diffraction, high-resolution transmission electron microscopy, and Mössbauer spectroscopy. This entails optical-band-gap narrowing from 3.05 to 2.30 eV. The pros and cons effects of doping on the electrochemical properties of TiO2 versus lithium are herein discussed. We reveal that doping improves the power rate capability of the electrode but, in turn, deserves the electrolyte stability, leading to early formation of SEI. Finally, we highlight a beneficial effect of low iron introduction into the anatase lattice for photocatalytic applications under standard AM1.5G visible-light illumination.