N. N. Demchenko

Laser interactions with plastic foam—metallic foil layered targets

Interactions of the laser beam of iodine laser PALS with low-density foam targets and acceleration of Al foils by the pressure of heated foam matter are investigated here, both experimentally and theoretically. An x-ray streak camera was used for the evaluation of the speed of energy transfer through the porous foam material. X-ray streak records show no noticeable emission near the Al foil at the rear side of a 400 µm thick foam and, thus, Al foil is most likely accelerated without significant heating and expansion. Accelerated foil velocities, measured by three-frame optical shadowgraphy, reach up to 107 cm s−1. Experimental results compare well with our two-dimensional hydrodynamics simulations and with an approximate analytical model.

Pre-plasma effect on laser beam energy transfer to a dense target under conditions relevant to shock ignition

This paper reports on properties of a plasma formed by sequential action of two laser beams on a flat target, simulating the conditions of shock-ignited inertial confinement fusion target exposure. The experiments were performed using planar targets consisting of a massive copper (Cu) plate coated with a thin plastic (CH) layer, which was irradiated by the 1ω PALS laser beam ( λ xa0=xa01.315xa0μm) at the energy of 250xa0J. The intensity of the fixed-energy laser beam was scaled by varying the focal spot radius. To imitate shock ignition conditions, the lower-intensity auxiliary 1ω beam created CH-pre-plasma which was irradiated by the main beam with a delay of 1.2xa0ns, thus generating a shock wave in the massive part of the target. To study the parameters of the plasma treated by the two-beam irradiation of the targets, a set of various diagnostics was applied, namely: (i) Two-channel polaro-interferometric system irradiated by the femtosecond laser (~40xa0fs), (ii) spectroscopic measurements in the X-ray range, (iii) two-dimensional (2D)-resolved imaging of the K α line emission from Cu, (iv) measurements of the ion emission by means of ion collectors, and (v) measurements of the volume of craters produced in a massive target providing information on the efficiency of the laser energy transfer to the shock wave. The 2D numerical simulations have been used to support the interpretation of experimental data. The general conclusion is that the fraction of the main laser beam energy deposited into the massive copper at two-beam irradiation decreases in comparison with the case of pre-plasma. The reason is that the pre-formed and expanding plasma deteriorates the efficiency of the energy transfer from the main laser pulse to a solid part of the targets by means of the fast electrons and the wave of an electron thermal conductivity.

Laser-produced aluminum plasma expansion inside a plastic plasma envelope

Previous experimental results demonstrated that the plasma pressure decreases with the growing atomic number of the target material. In this context, a question arose if the Al plasma outflow could be collimated using the plastic plasma as a compressor. To solve this problem, an experiment using a plastic target with an Al cylindrical insert was performed. The focal spot diameter substantially larger than that of the insert ensured simultaneous heating both target materials. This experiment proved that a production of Al plasma jets collimated by an action of outer plastic plasma is feasible [Kasperczuk et al., Laser Part. Beams 30, 1 (2012)]. The results of investigations presented here provide additional information on distributions of electron temperature in the outflowing plasma and time and space characteristics of ion emission, both registered at bare and constrained-flow Al targets. The experiment was carried out at the Prague asterix laser system iodine laser facility. The laser provided a 250 ps ...

Impact-driven shock waves and thermonuclear neutron generation

Impact-driven shock waves, thermonuclear plasma and neutron yield were investigated. The results of 2D numerical simulations and Gekko/HIPER laser experiments on the collision of a laser-accelerated disk-projectile with a massive target, both containing (CD)n-material, are discussed. A two-temperature model of the non-equilibrium plasma created by impact-driven shock waves due to the collision of a laser-accelerated planar projectile with a massive target was developed and used for analysis of the numerical and experimental results. The model defines the characteristics of shock waves and plasmas (including their lifetime) as well as neutron yields in both the colliding objects as functions of velocity, density and mass of the projectile–impactor just before collision. The neutron yield generated during the period of laser-driven acceleration of the impactor was also determined.Two effects were discovered that exert a substantial influence on the plasma parameters and neutron yield. The first of them relates to the formation of the pre-impact state of the impactor. It decreases the projectile density due to thermal expansion of its matter through a free boundary during the period of laser-driven acceleration. The other relates to the formation of impact-produced plasma. Predominant heating of the ion component of plasma leads to the existence of a non-equilibrium two-temperature plasma during the period of electron–ion relaxation.

Laser-driven acceleration of a dense matter up to ‘thermonuclear’ velocities

The results of theoretical studies and numerical simulations of laser-driven acceleration of a flat foil up to ultrahigh velocity of the order of 1000 km s−1, which corresponds to the achievement of thermonuclear temperatures due to kinetic energy transition into thermal energy at an inelastic impact, are reported. The behavior of a foil accelerated to such high velocities, in particular, the distribution of foil density, which defines thermonuclear reaction intensity, has been studied. The calculation results are compared with the results of the experiments performed on the Gekko/HIPER laser, where a laser-driven projectile achieved record-breaking velocity. The laser pulse and foil parameters responsible for acceleration of the projectile up to thermonuclear velocities in a dense state have been determined.

Influence of low atomic number plasma component on the formation of laser-produced plasma jets

The results of investigations are presented that are connected with a very simple method of plasma jet formation, which consists in irradiating a massive planar target made of material with relatively high atomic number by a partly defocused laser beam. This brief communication is aimed at investigations of interaction of axially symmetrical light (plastic-CH) plasma with heavy (copper) plasma. It demonstrates that a relatively thin plastic plasma envelope can compress the Cu plasma and control the Cu-jet formation.

A Hydrodynamic Model of the Interaction of Picosecond Laser Pulses with Condensed Targets

We consider a physical model of the interaction of high‐power laser pulses with plasma created upon irradiation of condensed targets. The model is based on the equations of single‐fluid, two‐temperature hydrodynamics taking into account the ponderomotive force, and the Maxwell equations for laser radiation at oblique incidence in the cases of s‐ and p‐polarizations. The model takes into account the generation of fast electrons in the conditions of plasma resonance at the critical surface, and their transport with consideration for the friction force, caused by the ionization losses. Heating of ions in the plasma due to beats of the ponderomotive potential is considered. The results of numerical modeling of the interaction of a picosecond laser pulse, containing a prepulse, with a deuterium target at power densities of 1016–1017 W/cm2 are presented. It is shown that the neutron yield of the DD‐reaction decreases with increase in prepulse energy, because the plasma created inhibits heating of the dense region of the target where a high rate of the reactions can be realized. It is also shown that the laser radiation losses caused by the stimulated scattering increase with increase in prepulse energy.

Thermonuclear targets for direct-drive ignition by a megajoule laser pulse

Central ignition of a thin two-layer-shell fusion target that is directly driven by a 2-MJ profiled pulse of Nd laser second-harmonic radiation has been studied. The parameters of the target were selected so as to provide effective acceleration of the shell toward the center, which was sufficient for the onset of ignition under conditions of increased hydrodynamic stability of the ablator acceleration and compression. The aspect ratio of the inner deuterium-tritium layer of the shell does not exceed 15, provided that a major part (above 75%) of the outer layer (plastic ablator) is evaporated by the instant of maximum compression. The investigation is based on two series of numerical calculations that were performed using one-dimensional (1D) hydrodynamic codes. The first 1D code was used to calculate the absorption of the profiled laser-radiation pulse (including calculation of the total absorption coefficient with allowance for the inverse bremsstrahlung and resonance mechanisms) and the spatial distribution of target heating for a real geometry of irradiation using 192 laser beams in a scheme of focusing with a cubo-octahedral symmetry. The second 1D code was used for simulating the total cycle of target evolution under the action of absorbed laser radiation and for determining the thermonuclear gain that was achieved with a given target.

Effect of spatial nonuniformity of heating on compression and burning of a thermonuclear target under direct multibeam irradiation by a megajoule laser pulse

Direct-drive fusion targets are considered at present as an alternative to targets of indirect compression at a laser energy level of about 2 MJ. In this approach, the symmetry of compression and ignition of thermonuclear fuel play the major role. We report on the results of theoretical investigation of compression and burning of spherical direct-drive targets in the conditions of spatial nonuniformity of heating associated with a shift of the target from the beam center of focusing and possible laser radiation energy disbalance in the beams. The investigation involves numerous calculations based on a complex of 1D and 2D codes RAPID, SEND (for determining the target illumination and the dynamics of absorption), DIANA, and NUT (1D and multidimensional hydrodynamics of compression and burning of targets). The target under investigation had the form of a two-layer shell (ablator made of inertial material CH and DT ice) filled with DT gas. We have determined the range of admissible variation of compression and combustion parameters of the target depending on the variation of the spatial nonuniformity of its heating by a multibeam laser system. It has been shown that low-mode (long-wavelength) perturbations deteriorate the characteristics of the central region due to less effective conversion of the kinetic energy of the target shell into the internal energy of the center. Local initiation of burning is also observed in off-center regions of the target in the case of substantial asymmetry of irradiation. In this case, burning is not spread over the entire volume of the DT fuel as a rule, which considerably reduces the thermonuclear yield as compared to that in the case of spherical symmetry and central ignition.

Interaction of laser radiation with a low-density structured absorber

A theoretical model is proposed for computing simulations of laser radiation interaction with inhomogeneous foam materials doped with heavy elements and undoped materials. The model satisfactorily describes many experiments on the interaction of the first and third harmonics of a 200 J pulsed PALS iodine laser with low-density porous cellulose triacetate targets. The model can be used to analyze experimental data and estimate the reality of experimental results.