N. Ordás

Self-passivating bulk tungsten-based alloys manufactured by powder metallurgy

Self-passivating tungsten-based alloys are expected to provide a major safety advantage compared to pure tungsten, which is at present the main candidate material for the first wall armour of future fusion reactors. WC10Si10 alloys were manufactured by mechanical alloying (MA) in a Planetary mill and subsequent hot isostatic pressing (HIP), achieving densities above 95%. Different MA conditions were studied. After MA under optimized conditions, a core with heterogeneous microstructure was found in larger powder particles, resulting in the presence of some large W grains after HIP. Nevertheless, the obtained microstructure is significantly refined compared to previous work. First MA trials were also performed on the Si-free system WCr12Ti2.5. In this case a very homogeneous structure inside the powder particles was obtained, and a majority ternary metastable bcc phase was found, indicating that almost complete alloying occurred. Therefore, a very fine and homogeneous microstructure can be expected after HIP in future work.

Residual stresses in tool steel due to hard-turning

Residual stresses induced by hard-turning are the result of a combination of mechanical and thermal effects, leading to a compressive or tensile stress state at the surface, depending on the machining parameters and the tool wear state. In this work, the residual stress depth profiles generated on steel grade F-521 (AISI D2) by hard-turning with tools of different wear states were measured by X-ray diffraction. An integral method was applied to determine the full stress tensor and the stress gradient tensors in the tangential, radial and depth directions. Both macroscopic and microscopic residual stresses were investigated. Compressive residual stresses were measured below the surface in all machined specimens. The magnitude of the compressive stress was much lower and the depth was much shallower when using new cutting tools than when using worn tools. However, the sample that has been hard-turned with a worn tool suffered strong microstructural changes in a layer more than 150 μm thick, especially at the surface, where the presence of a hard and very brittle layer of untempered martensite was evidenced.

Manufacturing of self-passivating tungsten based alloys by different powder metallurgical routes

Self-passivating tungsten based alloys will provide a major safety advantage compared to pure tungsten when used as first wall armor of future fusion reactors, due to the formation of a protective oxide layer which prevents the formation of volatile and radioactive WO3 in case of a loss of coolant accident with simultaneous air ingress. Bulk WCr10Ti2 alloys were manufactured by two different powder metallurgical routes: (1) mechanical alloying (MA) followed by hot isostatic pressing (HIP) of metallic capsules, and (2) MA, compaction, pressureless sintering in H2 and subsequent HIPing without encapsulation. Both routes resulted in fully dense materials with homogeneous microstructure and grain sizes of 300 nm and 1 μm, respectively. The content of impurities remained unchanged after HIP, but it increased after sintering due to binder residue. It was not possible to produce large samples by route (2) due to difficulties in the uniaxial compaction stage. Flexural strength and fracture toughness measured on samples produced by route (1) revealed a ductile-to-brittle-transition temperature (DBTT) of about 950 °C. The strength increased from room temperature to 800 °C, decreasing significantly in the plastic region. An increase of fracture toughness is observed around the DBTT.

Manufacturing and high heat-flux testing of brazed actively cooled mock-ups with Ti-doped graphite and CFC as plasma-facing materials

In the frame of the EU project ExtreMat new Ti-doped isotropic graphites and carbon fibre-reinforced carbons (CFCs) with high thermal conductivity and reduced chemical erosion were brazed to a CuCrZr heat-sink to produce flat-tile actively cooled mock-ups (MUs). Brazing was done using a low CTE interlayer to shift the stresses to the metal?metal interface. These MUs were exposed to high heat-fluxes in the electron beam facility JUDITH. Screening tests were conducted increasing the heat load stepwise up to 15?MW?m?2, followed by 100 cycles at 15?MW?m?2, subsequent screening up to 20?MW?m?2 and 100 cycles at 20?MW?m?2. All MUs withstood screening at 15?MW?m?2 and most of them survived screening at 20?MW?m?2. Ti-doped CFC MUs showed a significant improvement compared with the undoped reference CFC, surviving several cycles at 20?MW?m?2 on all tiles. One of the Ti-doped graphite MUs withstood 100 cycles at 20?MW?m?2 on one tile, representing a promising result.

ODS ferritic steels produced by an alternative route (STARS): microstructural characterisation after atomisation, HIPping and heat treatments

The conventional PM ODS Ferritic Steel (FS) processing route includes gas atomisation of steel powder and its mechanical alloying (MA) with Y2O3 powder particles to dissolve yttrium and form, during consolidation, a dispersion of oxide nanoparticles (Y–Ti–O) in a nanostructured matrix. This work presents an alternative route to produce ODS steels avoiding MA: STARS (Surface Treatment of gas Atomized powder followed by Reactive Synthesis). STARS FS powders with composition Fe–14Cr–2W–0.3Ti–0.23Y, already containing the nanoparticles precursors, were gas-atomized. Oxygen, Y and Ti contents were tailored to the required values to form Y–Ti–O nanoparticles during processing. Powders were HIPped at 900, 1220 and 1300°C. Specimens HIPped at 900 and 1220°C were heat treated (HT) at temperatures ranging from 1200 to 1320°C. The microstructural evolution with HIP and HT temperatures, including characterisation of nanoparticles and feasibility of achieving complete dissolution of prior particle boundaries (PPBs) were assessed.

Fracture strength testing of a self-passivating tungsten alloy at the micrometre scale

Abstract The brittle fracture strength of a self-passivating W-Cr10-Ti2 alloy (in wt.%) was measured through un-notched cantilever bending at the microscopic scale. The material behaved purely elastic and fractured catastrophically in an unstable fashion. An average nominal strength of 5.9 GPa was measured. The scatter in strength was shown to be significantly higher than the sum of all random errors indicating an inherent variability of the material’s strength. The measurements from 28 tests followed a Weibull distribution with a modulus of m = 12. Results from a size effect study at the microscopic scale were successfully predicted through Weibull scaling. Extrapolation into the macroscopic range overestimated the measured three-point bend strength, which is likely due to the presence of large-scale heterogeneities. The test technique sampled a material thickness of only several micrometres and is hence suitable for future ion irradiation studies.