Nam Dong Kim

Atomic cobalt on nitrogen-doped graphene for hydrogen generation

Reduction of water to hydrogen through electrocatalysis holds great promise for clean energy, but its large-scale application relies on the development of inexpensive and efficient catalysts to replace precious platinum catalysts. Here we report an electrocatalyst for hydrogen generation based on very small amounts of cobalt dispersed as individual atoms on nitrogen-doped graphene. This catalyst is robust and highly active in aqueous media with very low overpotentials (30u2009mV). A variety of analytical techniques and electrochemical measurements suggest that the catalytically active sites are associated with the metal centres coordinated to nitrogen. This unusual atomic constitution of supported metals is suggestive of a new approach to preparing extremely efficient single-atom catalysts.

High-Performance Pseudocapacitive Microsupercapacitors from Laser-Induced Graphene.

All-solid-state, flexible, symmetric, and asymmetric microsupercapacitors are fabricated by a simple method in a scalable fashion from laser-induced graphene on commercial polyimide films, followed by electrodeposition of pseudocapacitive materials on the interdigitated in-plane architectures. These microsupercapacitors demonstrate comparable energy density to commercial lithium thin-film batteries, yet exhibit more than two orders of magnitude higher power density with good mechanical flexibility.

Lithium Batteries with Nearly Maximum Metal Storage

The drive for significant advancement in battery capacity and energy density inspired a revisit to the use of Li metal anodes. We report the use of a seamless graphene-carbon nanotube (GCNT) electrode to reversibly store Li metal with complete dendrite formation suppression. The GCNT-Li capacity of 3351 mAh g-1GCNT-Li approaches that of bare Li metal (3861 mAh g-1Li), indicating the low contributing mass of GCNT, while yielding a practical areal capacity up to 4 mAh cm-2 and cycle stability. A full battery based on GCNT-Li/sulfurized carbon (SC) is demonstrated with high energy density (752 Wh kg-1 total electrodes, where total electrodes = GCNT-Li + SC + binder), high areal capacity (2 mAh cm-2), and cyclability (80% retention at >500 cycles) and is free of Li polysulfides and dendrites that would cause severe capacity fade.

Chemical Mass Production of Graphene Nanoplatelets in ∼100% Yield

Successful application of graphene is hampered by the lack of cost-effective methods for its production. Here, we demonstrate a method of mass production of graphene nanoplatelets (GNPs) by exfoliation of flake graphite in the tricomponent system made by a combination of ammonium persulfate ((NH4)2S2O8), concentrated sulfuric acid, and fuming sulfuric acid. The resulting GNPs are tens of microns in diameter and 10-35 nm in thickness. When in the liquid phase of the tricomponent media, graphite completely loses its interlayer registry. This provides a ∼100% yield of GNPs from graphite in 3-4 h at room temperature or in 10 min at 120 °C.

Tin Disulfide Nanoplates on Graphene Nanoribbons for Full Lithium Ion Batteries.

A nanocomposite material made of layered tin disulfide (SnS2) nanoplates vertically grown on reduced graphene oxide nanoribbons (rGONRs) has been successfully developed as an anode in lithium ion batteries by a facile method. At a rate of 0.4 A/g, the material exhibits a high discharge capacity of 823 mAh/g even after 800 cycles. It shows excellent rate stability when the current density varies from 0.1 to 3.0 A/g with a Coulombic efficiency larger than 99%. In order to demonstrate the anode material for practical applications, SnS2-rGONR/LiCoO2 full cells were constructed. To the best of our knowledge, this is the first time that a full cell has been successfully developed using metal chalcogenides as an anode. The full cell delivers a high capacity of 642 mAh/g at 0.2 A/g, superior rate, and cycling stability after long-term cycling. Moreover, the full cell has a high output working voltage of 3.4 V. These excellent lithium storage performances in half and full cells can be mainly attributed to the synergistic effect between the highly conductive network of rGONRs and the high lithium-ion storage capability of layered SnS2 nanoplates.

Graphene Carbon Nanotube Carpets Grown Using Binary Catalysts for High-Performance Lithium-Ion Capacitors

Here we show that a versatile binary catalyst solution of Fe3O4/AlOx nanoparticles enables homogeneous growth of single to few-walled carbon nanotube (CNT) carpets from three-dimensional carbon-based substrates, moving past existing two-dimensional limited growth methods. The binary catalyst is composed of amorphous AlOx nanoclusters over Fe3O4 crystalline nanoparticles, facilitating the creation of seamless junctions between the CNTs and the underlying carbon platform. The resulting graphene-CNT (GCNT) structure is a high-density CNT carpet ohmically connected to the carbon substrate, an important feature for advanced carbon electronics. As a demonstration of the utility of this approach, we use GCNTs as anodes and cathodes in binder-free lithium-ion capacitors, producing stable devices with high-energy densities (∼120 Wh kg-1), high-power density capabilities (∼20,500 W kg-1 at 29 Wh kg-1), and a large operating voltage window (4.3 to 0.01 V).

Carbon-Free Electrocatalyst for Oxygen Reduction and Oxygen Evolution Reactions.

A nanoporous Ag-embedded SnO2 thin film was fabricated by anodic treatment of electrodeposited Ag-Sn alloy layers. The ordered nanoporous structure formed by anodization played a key role in enhancing the electrocatalytic performance of the Ag-embedded SnO2 layer in several ways: (1) the roughness factor of the thin film is greatly increased from 23 in the compact layer to 145 in the nanoporous layer, creating additional active sites that are involved in oxygen electrochemical reactions; (2) a trace amount of Ag (∼1.7 at %, corresponding to a Ag loading of ∼3.8 μg cm(-2)) embedded in the self-organized SnO2 nanoporous matrix avoids the agglomeration of nanoparticles, which is a common problem leading to the electrocatalyst deactivation; (3) the fabricated nanoporous thin film is active without additional additives or porous carbon that is usually necessary to support and stabilize the electrocatalyst. More importantly, the Ag-embedded SnO2 nanoporous thin film shows outstanding bifunctional oxygen electrochemical performance (oxygen reduction and evolution reactions) that is considered a promising candidate for use in metal-air batteries. The present technique has a wide range of applications for the preparation of other carbon-free electrocatalytic nanoporous films that could be useful for renewable energy production and storage applications.

Three-Dimensional Networked Nanoporous Ta2O5–x Memory System for Ultrahigh Density Storage

Oxide-based resistive memory systems have high near-term promise for use in nonvolatile memory. Here we introduce a memory system employing a three-dimensional (3D) networked nanoporous (NP) Ta2O5-x structure and graphene for ultrahigh density storage. The devices exhibit a self-embedded highly nonlinear I-V switching behavior with an extremely low leakage current (on the order of pA) and good endurance. Calculations indicated that this memory architecture could be scaled up to a ∼162 Gbit crossbar array without the need for selectors or diodes normally used in crossbar arrays. In addition, we demonstrate that the voltage point for a minimum current is systematically controlled by the applied set voltage, thereby offering a broad range of switching characteristics. The potential switching mechanism is suggested based upon the transformation from Schottky to Ohmic-like contacts, and vice versa, depending on the movement of oxygen vacancies at the interfaces induced by the voltage polarity, and the formation of oxygen ions in the pores by the electric field.

Growth and Transfer of Seamless 3D Graphene–Nanotube Hybrids

Seamlessly connected graphene and carbon nanotube hybrids (GCNTs) have great potential as carbon platform structures in electronics due to their high conductivity and high surface area. Here, we introduce a facile method for making patterned GCNTs and their intact transfer onto other substrates. The mechanism for selective growth of vertically aligned CNTs (VA-CNTs) on the patterned graphene is discussed. The complete transfer of the GCNT pattern onto other substrates is possible because of the mechanical strength of the GCNT hybrids. Electrical conductivity measurements of the transferred GCNT structures show Ohmic contact through the VA-CNTs to graphene--evidence of its integrity after the transfer process.

Microwave Heating of Functionalized Graphene Nanoribbons in Thermoset Polymers for Wellbore Reinforcement.

Here, we introduce a systematic strategy to prepare composite materials for wellbore reinforcement using graphene nanoribbons (GNRs) in a thermoset polymer irradiated by microwaves. We show that microwave absorption by GNRs functionalized with poly(propylene oxide) (PPO-GNRs) cured the composite by reaching 200 °C under 30 W of microwave power. Nanoscale PPO-GNRs diffuse deep inside porous sandstone and dramatically enhance the mechanics of the entire structure via effective reinforcement. The bulk and the local mechanical properties measured by compression and nanoindentation mechanical tests, respectively, reveal that microwave heating of PPO-GNRs and direct polymeric curing are major reasons for this significant reinforcement effect.