Nebojsa Milovanovic

Investigation of the Combustion Characteristics with Focus on Partially Premixed Combustion in a Heavy Duty Engine

Partially Premixed Combustion (PPC) has shown its potential by combining high combustion controllability with emission characteristics that are close to those of an HCCI engine. In order to get PPC the ignition delay needs to be long enough for the fuel and air to mix prior to combustion. This can be achieved by injecting the fuel sufficiently early while running with high EGR.In order to find out where and how PPC occurs a map that shows the changes in combustion characteristics with injection timing and EGR was created. The combustion characteristics were studied in a six cylinder heavy duty engine where the Start of Injection (SOI) was swept from early to late injection over a wide range of EGR levels. The emissions were monitored during the sweeps and in the most promising regions, with low emissions and high efficiency, additional changes in injection pressure and engine speed were applied to get a more versatile picture of the combustion. (Less)

Deposit Formation in the Holes of Diesel Injector Nozzles: A Critical Review

Current developments in fuels and emissions regulations are resulting in increasingly severe operating environment for the injection system. Formation of deposits within the holes of the injector nozzle or on the outside of the injector tip may have an adverse effect on overall system performance. This paper provides a critical review of the current understanding of the main factors affecting deposit formation. Two main types of engine test cycles, which attempt to simulate field conditions, are described in the literature. The first type involves cycling between high and low load. The second involves steady state operation at constant speed either at medium or high load. A number of influences on the creation of deposits are identified. This includes fouling through thermal condensation and cracking reactions at nozzle temperatures of around 300°C. Also the design of the injector holes is an influence, because it can influence cavitation. The implosion of cavitation bubbles is believed to limit nozzle deposits. Field and laboratory tests showed that small amounts (around 1ppm) of zinc tend to increase the formation of deposits and are therefore another influence. But it is not clear whether zinc acts catalytically to accelerate deposit formation or if it becomes part of the solid deposits. Bio-diesel has been observed to lead to higher deposit formation in the injector nozzle. The chemical and physical processes that lead to deposit formation are not known or well understood, due to their complexity. A physical mechanism put forward focuses on the role of the residual fuel that remains in the nozzle holes after the end of the injection process.

The Impact of Injection Strategies on Emissions Reduction and Power Output of Future Diesel Engines

ABSTRACT Future light, medium and heavy duty diesel engines will need to satisfy the more stringent emission levels (US 2014, Euro 6, etc.) without compromising their current performance and fuel economy, while still maintaining a competitive cost. In order to achieve this, the Fuel Injection Equipment (FIE) together with the pressure charging, cooling system, exhaust after treatment and other engine sub-systems will each play a key role. The FIE has to offer a range of flexible injection characteristics, e.g. a multiple injection train with or without separation, modulated injection pressures and rates for every injection, higher specific power output from the same injector envelope, and close control of very small fuel injection quantities. The aim of this paper is to present Delphi’s developments in fuel injection strategies for light and medium duty diesel engines that will comply with future emission legislation, whilst providing higher power density and uncompromised fuel economy.

Evaluation of the Operating Range of Partially Premixed Combustion in a Multi Cylinder Heavy Duty Engine with Extensive EGR

Partially Premixed Combustion (PPC) is a combustion concept by which it is possible to get low smoke and NOx emissions simultaneously. PPC requires high EGR levels and injection timings sufficiently early or late to extend the ignition delay so that air and fuel mix extensively prior to combustion. This paper investigates the operating region of single injection diesel PPC in a multi cylinder heavy duty engine resembling a standard build production engine. Limits in emissions and fuel consumption are defined and the highest load that fulfills these requirements is determined. Experiments are carried out at different engine speeds and a comparison of open and closed loop combustion control are made as well as evaluation of an extended EGR-cooling system designed to reduce the EGR temperature. In this study the PPC operating range proved to be limited. The highest loads that fulfilled the emission criteria correspond to 30% of maximum load for conventional combustion at low speed and 21% of maximum load for conventional combustion at high speed. The effect of changes in combustion control was small while a reduced EGR temperature could increase the operating range significantly. (Less)

Investigations on Deposit Formation in the Holes of Diesel Injector Nozzles

Current developments in fuels and emissions regulations are resulting in an increasingly severe operating environment for diesel fuel injection systems. The formation of deposits within the holes or on the outside of the injector nozzle can affect the overall system performance. The rate of deposit formation is affected by a number of parameters, including operating conditions and fuel composition. For the work reported here an accelerated test procedure was developed to evaluate the relative importance of some of these parameters in a high pressure common rail fuel injection system. The resulting methodology produced measurable deposits in a custom made injector nozzle on a single cylinder engine. The results indicate that fuels containing 30%v/v and 100% Fatty Acid Methyl Ester (FAME), that does not meet EN 14214 produced more deposit than an EN590 petroleum diesel fuel. Overall, the addition of zinc to the fuel had the biggest effect on deposit formation and resulted in a 12.2% decrease in Indicated Mean Effective Pressure (IMEP). The effects of zinc were unexpectedly reduced when it was added to fuel containing 30%v/v biodiesel. Reducing the common-rail pressure with 30%v/v biodiesel (no added zinc) increased the loss in IMEP. Raising the air and fuel temperatures by 40°C and 30°C respectively showed no bigger loss in IMEP. The results indicate that deposit formation may continue after engine shut down.