Nick Polychronakis

Effects of cleansing methods on 3-D surface roughness, gloss and color of a polyamide denture base material

Abstract Objective. The purpose of this study was to determine the effects of two denture cleansing methods on 3-D surface roughness, gloss and color of denture base materials. Materials and methods. Thirty disks from nylon (Valplast) and 30 from heat-polymerized acrylic denture base material (Paladon 65) were made and 10 of each material were immersed in water (control), Val-Clean (peroxide cleanser) and Corega Extradent (peroxide cleanser) plus microwaving for a period simulating 30 days of daily cleansing. 3-D surface roughness, gloss and color parameters were measured before and after cleansing using an interferometric profilometer, a gloss meter and a colorimeter. The results were statistically analysed by regression, paired-t, Mann-Whitney and Kruskal-Wallis tests at α = 0.05 level of significance. Results. The results showed significant differences at baseline in L* and b* parameters between materials (p < 0.01), with a significantly lower gloss (p < 0.05) and higher roughness (p < 0.05) for Valplast. After cleansing, Δε* was significantly greater in Valplast than Paladon 65 (p < 0.05). Gloss of both materials decreased significantly within the Corega Extradent plus microwave solution (p < 0.05), while roughness increased significantly only for Paladon 65 (p < 0.05). Conclusions. Valplast was found to have a significantly lower gloss and a higher roughness than Paladon 65 before cleansing. After cleansing, ΔE* increased more in Valplast than in Paladon 65, gloss of both materials decreased and roughness only of Paladon 65 increased within the Corega extradent plus microwaving method.

A Survey of Removable Partial Denture Casts and Major Connector Designs Found in Commercial Laboratories, Athens, Greece

PURPOSE This survey was conducted to study the prevalence of partial edentulism, the type of removable partial denture (RPD) support, the type of major connectors, and the frequency of their use in relation to the partial edentulism classes encountered, concerning patients in Athens, Greece. MATERIALS AND METHODS The material comprised 628 final casts for RPDs. Each cast was photographed in a way that would allow the number of existing teeth, the classification of partial edentulism, the RPD support, and the particular parts of the metal framework to be identified. Data collected were analyzed statistically using prevalence tables and the χ(2) test. RESULTS Two hundred seventy six (43.9%) casts were for the maxilla and 352 (56.1%) for the mandible. The most frequently encountered group was Kennedy class I for both arches, while class IV was the classification least encountered (p < 0.001). Of all RPDs constructed, 96.8% had a metal framework (tooth-borne and tooth/tissue-borne), while 3.2% of the RPDs were frameless (tissue-borne, acrylic dentures). The U-shaped palatal connector (horseshoe) in the maxilla and the lingual bar in the mandible were the most frequently used for all partial edentulism classes, at 55.2% and 95%, respectively. CONCLUSIONS Analysis of the casts revealed that the type of major connectors selected does not comply with the indications for their applications, considering the lack of dental history and clinical examination. This notes the need for further training dentists and dental technicians in aspects of RPD framework design.

Long-term microwaving of denture base materials: effects on dimensional, color and translucency stability

Abstract While the combined effect of microwave irradiation with cleansing solutions on denture base materials has been investigated, the effects of only using microwave irradiation and, more importantly, in a long-term basis, was not studied yet. Objective The purpose of this study was to evaluate the effect of a long-term repeated microwaving on the dimensional, color and translucency stability of acrylic and polyamide denture base materials. Material and Methods Thirty two specimens (32 mm x 10 mm x 2.5 mm) from polyamide (Valplast) and PMMA (Vertex Rapid Simplified) denture base materials were made. Eight specimens from each material were immersed in distilled water (control) and 8 were subjected to microwave exposure at 450 W for 3 minutes for a period simulating 224 days of daily disinfection. Linear dimension, color change (ΔE*) and translucency parameter (TP) were measured at baseline and after certain intervals up to 224 cycles of immersion, using a digital calliper and a portable colorimeter. The results were analysed using two-way repeated measures ANOVA to estimate possible differences among predetermined cycles and material type. Regression analysis was also performed to estimate the trend of changes with time. Statistical evaluations performed at a significance level of 5%. Results Data analysis showed significant changes in length at baseline with an increasing number of cycles (p<0.05) and a significant interaction of cycle-material (p<0.001). The ΔΕ* parameter was significantly higher with a higher number of cycles (p<0.001), but it did not vary between materials (p>0.05). TP decreased similarly in both materials following microwave action but in a significantly higher level for Valplast (p<0.001). Conclusions The results indicated that long-term repeated microwaving affects linear dimensional, color and translucency changes of both materials. Differences between PMMA and polyamide material were noted only in dimension and translucency changes.

The Influence of Thermocycling on the Flexural Strength of a Polyamide Denture Base Material

Objective The aim of the present study was to evaluate the influence of thermocycling on the flexural strength of a polyamide base denture material. Materials and methods A polyamide denture base material (Valplast) was tested, whereas a PMMA material (Vertex) was used as a control. Thirty specimens of each material were fabricated for flexural strength testing according to ISO 1567. They were prepared and stored in water at 37°C for 48 hours. The specimens of each material were divided into three equal groups (n=10). Flexural strength testing was performed immediately after water storage and after thermocycling (5°C / 55°C, 2 c/min) for 3000 and 5000 cycles. A three point flexural test was performed on a universal testing machine at a crosshead speed of 5 mm/min. The final flexural strength was calculated using the formula: FS = 3 PL/2 bd2. A two-way ANOVA with post-hoc analysis using Tukeys procedure was applied at .05 level of statistical significance. Results A statistically significant reduction in flexural strength was recorded after thermocycling at 3000 cycles for PMMA and at 5000 cycles for both materials. The flexural strength of PMMA was significantly higher compared to polyamide for all the conditions tested (p<0.05). Conclusion Thermocycling had a significant adverse effect on the flexural strength of polyamide and PMMA denture base materials.

Pregled retencijskih elemenata mobilnih djelomičnih proteza ovisno o vrsti bezubosti i zubima nosačima u komercijalnim laboratorijima u Ateni

OBJECTIVE The aim of this survey was to record removable partial denture (RPD) retentive elements and abutment teeth in partially edentulous patients, identified in commercial laboratories in Athens, Greece. MATERIAL AND METHODS 628 master casts with the corresponding cast metal frameworks used in the construction of RPDs were evaluated. Casts were photographed to identify the number and position of existing teeth, the partial edentulism class and the retentive elements. Prevalence tables and the x(2) test were used for the statistical analysis of the collected data (α=.05). RESULTS There were 276 maxillary (43.9%) and 352 (56.1%) mandibular casts. Maxillary edentulism entailed almost a total absence of right third molars in 96.7% and left third molars 96.0% of casts, with lower rates for the first and second molars. Edentulism in the posterior mandible presented a similar pattern. The most profound findings concerning retentive elements were: 91.9% of the retainers used were clasps and the remaining 8.1% were attachments. Of the clasps used, 48.9% were of the Roach Τ type, a finding more common in Kennedy Class I as compared to other Kennedy Classes (p<0.01). The circumferential clasps accounted for 19.3% of the total clasps used, and it was less frequently presented (8.8%) in Kennedy I Classes (p<0.01). CONCLUSIONS Roach clasps were used in the majority of cases whereas RPI clasps and attachments were rarely used.

A Survey of Removable Partial Denture (RPD) Retentive Elements in Relation to the Type of Edentulism and Abutment Teeth Found in Commercial Laboratories, Athens, Greece.

OBJECTIVE The aim of this survey was to record removable partial denture (RPD) retentive elements and abutment teeth in partially edentulous patients, identified in commercial laboratories in Athens, Greece. MATERIAL AND METHODS 628 master casts with the corresponding cast metal frameworks used in the construction of RPDs were evaluated. Casts were photographed to identify the number and position of existing teeth, the partial edentulism class and the retentive elements. Prevalence tables and the x(2) test were used for the statistical analysis of the collected data (α=.05). RESULTS There were 276 maxillary (43.9%) and 352 (56.1%) mandibular casts. Maxillary edentulism entailed almost a total absence of right third molars in 96.7% and left third molars 96.0% of casts, with lower rates for the first and second molars. Edentulism in the posterior mandible presented a similar pattern. The most profound findings concerning retentive elements were: 91.9% of the retainers used were clasps and the remaining 8.1% were attachments. Of the clasps used, 48.9% were of the Roach Τ type, a finding more common in Kennedy Class I as compared to other Kennedy Classes (p<0.01). The circumferential clasps accounted for 19.3% of the total clasps used, and it was less frequently presented (8.8%) in Kennedy I Classes (p<0.01). CONCLUSIONS Roach clasps were used in the majority of cases whereas RPI clasps and attachments were rarely used.

A Survey of Removable Partial Denture (RPD) Retentive Elements in Relation to Type of Edentulism and Abutment Teeth in Commercial Laboratories in Athens

OBJECTIVE The aim of this survey was to record removable partial denture (RPD) retentive elements and abutment teeth in partially edentulous patients, identified in commercial laboratories in Athens, Greece. MATERIAL AND METHODS 628 master casts with the corresponding cast metal frameworks used in the construction of RPDs were evaluated. Casts were photographed to identify the number and position of existing teeth, the partial edentulism class and the retentive elements. Prevalence tables and the x(2) test were used for the statistical analysis of the collected data (α=.05). RESULTS There were 276 maxillary (43.9%) and 352 (56.1%) mandibular casts. Maxillary edentulism entailed almost a total absence of right third molars in 96.7% and left third molars 96.0% of casts, with lower rates for the first and second molars. Edentulism in the posterior mandible presented a similar pattern. The most profound findings concerning retentive elements were: 91.9% of the retainers used were clasps and the remaining 8.1% were attachments. Of the clasps used, 48.9% were of the Roach Τ type, a finding more common in Kennedy Class I as compared to other Kennedy Classes (p<0.01). The circumferential clasps accounted for 19.3% of the total clasps used, and it was less frequently presented (8.8%) in Kennedy I Classes (p<0.01). CONCLUSIONS Roach clasps were used in the majority of cases whereas RPI clasps and attachments were rarely used.