Nicolás Carrara

Metal and Precursor Effect during 1-Heptyne Selective Hydrogenation Using an Activated Carbon as Support

Palladium, platinum, and ruthenium supported on activated carbon were used as catalysts for the selective hydrogenation of 1-heptyne, a terminal alkyne. All catalysts were characterized by temperature programmed reduction, X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy. TPR and XPS suggest that the metal in all catalysts is reduced after the pretreatment with H2 at 673 K. The TPR trace of the PdNRX catalyst shows that the support surface groups are greatly modified as a consequence of the use of HNO3 during the catalyst preparation. During the hydrogenation of 1-heptyne, both palladium catalysts were more active and selective than the platinum and ruthenium catalysts. The activity order of the catalysts is as follows: PdClRX > PdNRX > PtClRX ≫ RuClRX. This superior performance of PdClRX was attributed in part to the total occupancy of the d electronic levels of the Pd metal that is supposed to promote the rupture of the H2 bond during the hydrogenation reaction. The activity differences between PdClRX and PdNRX catalysts could be attributed to a better accessibility of the substrate to the active sites, as a consequence of steric and electronic effects of the superficial support groups. The order for the selectivity to 1-heptene is as follows: PdClRX = PdNRX > RuClRX > PtClRX, and it can be mainly attributed to thermodynamic effects.

NANOPARTICLES OF TUNGSTEN AS LOW-COST MONOMETALLIC CATALYST FOR SELECTIVE HYDROGENATION OF 3-HEXYNE

to be active and stereoselective for the production of (Z)-3-hexene, had the following order: 7.1WN/A > 8.5 WN/A ≥ 4.5 WN/A. Additionally, the performance of the synthesized xWN/A catalysts exhibited high sensitivity to temperature variation. In all cases, the maximum 3-hexyne total conversion and selectivity was achieved at 323 K. The performance of the catalysts was considered to be a consequence of two phenomena: a) the electronic effects, related to the high charge of W (+6), causing an intensive dipole moment in the hydrogen molecule (van der Waals forces) and leading to heterolytic bond rupture; the H+ and H- species generated approach a 3-hexyne adsorbate molecule and cause heterolytic rupture of the C≡C bond into C- = C+; and b) steric effects related to the high concentration of WO3 on 8.5WN/A that block the Al2O3 support. Catalyst deactivation was detected, starting at about 50 min of reaction time. Electrodeficient W 6+ species are responsible for the formation of green oil at the surface level, blocking pores and active sites of the catalyst, particularly at low reaction temperatures (293 and 303 K). The resulting best catalyst, 7.1WN/A, has low fabrication cost and high selectivity for (Z)-3-hexene (94%) at 323 K. This selectivity is comparable to that of the classical and more expensive industrial Lindlar catalyst (5 wt% Pd). The alumina supported tungsten catalysts are low-cost potential replacements for the Lindlar industrial catalyst. These catalysts could also be used for preparing bimetallic W-Pd catalysts for selective hydrogenation of terminal and non-terminal alkynes.

High-Active Metallic-Activated Carbon Catalysts for Selective Hydrogenation

A series of low-loaded metallic-activated carbon catalysts were evaluated during the selective hydrogenation of a medium-chain alkyne under mild conditions. The catalysts and support were characterized by ICP, hydrogen chemisorption, Raman spectroscopy, temperature-programmed desorption (TPD), temperature-programmed reduction (TPR), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR micro-ATR), transmission electronic microscopy (TEM), and X-ray photoelectronic spectroscopy (XPS). When studying the effect of the metallic phase, the catalysts were active and selective to the alkene synthesis. NiCl/C was the most active and selective catalytic system. Besides, when the precursor salt was evaluated, PdN/C was more active and selective than PdCl/C. Meanwhile, alkyne is present in the reaction media, and geometrical and electronic effects favor alkene desorption and so avoid their overhydrogenation to the alkane. Under mild conditions, nickel catalysts are considerably more active and selective than the Lindlar catalyst.

SELECTIVE HYDROGENOLYSIS OF GLYCEROL TO PROPYLENE GLYCOL IN A CONTINUOUS FLOW TRICKLE BED REACTOR USING COPPER CHROMITE AND Cu/Al2O3 CATALYSTS

Fil: Sepulveda, Jorge. Consejo Nacional de Investigaciones Cientificas y Tecnicas. Centro Cientifico Tecnologico Conicet - Santa Fe. Instituto de Investigaciones en Catalisis y Petroquimica ; Argentina

New Strategies for Obtaining Inorganic-Organic Composite Catalysts for Selective Hydrogenation

Pd/composites are catalysts in which the catalytically active metal phase is located in a small layer on the support surface. The metal distribution obtained on these supports corresponds to a structure commonly known as “egg-shell”. This distribution is optimal for reactions that have heat or mass transfer resistances. The small thickness of the metal layer is mainly attributed to the use of support pellets of mixed organic–inorganic composition, the special interaction between the hydrophobic–hydrophillic support surface and the metal species (Pd or Pt) present in the impregnating aqueous solution. Pd/composite catalysts are active and selective for the reactions of selective hydrogenation of styrene, 1-heptyne, 3-hexyne and 2,3-butanone, and enantioselective hydrogenation of ethyl pyruvate. These reactions are of interest in both academic and industrial aspects.

THE WILKINSON COMPLEX AS A HETEROGENEOUS CATALYST IN THE PARTIAL HYDROGENATION OF 1-HEPTYNE. REGENERATION OF THE COMPLEX

The Wilkinson complex was tested as a catalyst in the partial hydrogenation of 1-heptyne, a medium chain alkyne, at a temperature of T = 303 K and hydrogen pressure PH2 = 150 kPa. The tests were performed in homogeneous system as well as heterogeneous system, supporting the complex on i) γ-Al2O3 and ii) a commercial carbonaceous material, RX3. Characterization by means of XPS and FTIR revealed that the anchored complex did not lose its chemical identity, being the catalytically active species. The Wilkinson complex on RX3 showed better conversions and selectivities, higher than the Lindlar catalyst, used as a reference. Additionally, it was proposed a method to recover Rh as a metal from the remaining solutions, and from it regenerate the complex to be reused from it.