Oliver Werzer

Bottom-up organic integrated circuits

Self-assembly—the autonomous organization of components into patterns and structures—is a promising technology for the mass production of organic electronics. Making integrated circuits using a bottom-up approach involving self-assembling molecules was proposed in the 1970s. The basic building block of such an integrated circuit is the self-assembled-monolayer field-effect transistor (SAMFET), where the semiconductor is a monolayer spontaneously formed on the gate dielectric. In the SAMFETs fabricated so far, current modulation has only been observed in submicrometre channels, the lack of efficient charge transport in longer channels being due to defects and the limited intermolecular π–π coupling between the molecules in the self-assembled monolayers. Low field-effect carrier mobility, low yield and poor reproducibility have prohibited the realization of bottom-up integrated circuits. Here we demonstrate SAMFETs with long-range intermolecular π–π coupling in the monolayer. We achieve dense packing by using liquid-crystalline molecules consisting of a π-conjugated mesogenic core separated by a long aliphatic chain from a monofunctionalized anchor group. The resulting SAMFETs exhibit a bulk-like carrier mobility, large current modulation and high reproducibility. As a first step towards functional circuits, we combine the SAMFETs into logic gates as inverters; the small parameter spread then allows us to combine the inverters into ring oscillators. We demonstrate real logic functionality by constructing a 15-bit code generator in which hundreds of SAMFETs are addressed simultaneously. Bridging the gap between discrete monolayer transistors and functional self-assembled integrated circuits puts bottom-up electronics in a new perspective.

Crystallisation kinetics in thin films of dihexyl-terthiophene: the appearance of polymorphic phases

The presence of surface-induced crystal structures is well known within organic thin films. However, the physical parameters responsible for their formation are still under debate. In the present work, we present the formation of polymorphic crystal structures of the molecule dihexyl-terthiophene in thin films. The films are prepared by different methods using solution-based methods like spin-coating, dip-coating and drop-casting, but also by physical vapour deposition. The thin films are characterised by various X-ray diffraction methods to investigate the crystallographic properties and by microscopy techniques (atomic force microscopy and optical microscopy) to determine the thin film morphologies. Three different polymorphic crystal structures are identified and their appearance is related to the film preparation parameters. The crystallisation speed is varied by the evaporation rate of the solvent and is identified as a key parameter for the respective polymorphs present in the films. Slow crystallisation speed induces preferential growth in the stable bulk structure, while fast crystallisation leads to the occurrence of a metastable thin-film phase. Furthermore, by combining X-ray reflectivity investigations with photoelectron spectroscopy experiments, the presence of a monolayer thick wetting layer below the crystalline film could be evidenced. This work gives an example of thin film growth where the kinetics during the crystallisation rather than the film thickness is identified as the critical parameter for the presence of a thin-film phase within organic thin films.

Compact poly(ethylene oxide) structures adsorbed at the ethylammonium nitrate-silica interface

The adsorption of poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) onto silica from ethylammonium nitrate (a protic ionic liquid) has been investigated using colloid probe AFM force curve measurements. Steric repulsive forces were measured for PEO, confirming that PEO can compete with the ethylammonium cation and adsorb onto silica. The range of the repulsion increases with polymer molecular weight (e.g., from 1.4 nm for 0.01 wt % 10 kDa PEO to 40 nm for 0.01 wt % 300 kDa PEO) and with concentration (e.g., from 16 nm at 0.001 wt % to 78 nm at 0.4 wt % for 300 kDa PEO). Fits to the force curve data could not be obtained using standard models for a polymer brush, but excellent fits were obtained using the mushroom model, suggesting the adsorbed polymer films are compressed and relatively poorly solvated. No evidence for adsorption of 3.5 kDa PPO could be detected up to its solubility limit.

Interface induced crystal structures of dioctyl-terthiophene thin films.

Temperature dependent structural and morphological investigations on semiconducting dioctyl-terthiophene (DOTT) thin films prepared on silica surfaces reveals the coexistence of surface induce order and distinct crystalline/liquid crystalline bulk polymorphs. X-ray diffraction and scanning force microscopy measurements indicate that at room temperature two polymorphs are present: the surface induced phase grows directly on the silica interface and the bulk phase on top. At elevated temperatures the long-range order gradually decreases, and the crystal G (340 K), smectic F (348 K), and smectic C (360 K) phases are observed. Indexation of diffraction peaks reveals that an up-right standing conformation of DOTT molecules is present within all phases. A temperature stable interfacial layer close to the silica-DOTT interface acts as template for the formation of the different phases. Rapid cooling of the DOTT sample from the smectic C phase to room temperature results in freezing into a metastable crystalline state with an intermediated unit cell between the room temperature crystalline phase and the smectic C phase. The understanding of such interfacial induced phases in thin semiconducting liquid crystal films allows tuning of crystallographic and therefore physical properties within organic thin films.

Temperature stability of the pentacene thin-film phase

This work presents the influence of temperatures above 300 K on the crystal structure and morphology of pentacene thin films. The thermal expansion of the unit cell and the relative amount of different phases are investigated via grazing incidence x-ray diffraction. Geometrical considerations about the specific molecular packing of the thin-film phase explain the anisotropic non-linear expansion. Furthermore, around 480 K, a phase transformation of the thin-film phase to the bulk phase is observed. In contrast, only a weak influence of the temperature on the height distribution of the thin-film phase crystallites is found.

Shear dependent viscosity of poly(ethylene oxide) in two protic ionic liquids

Steady shear viscosity measurements have been performed on 100 kDa poly(ethylene oxide) (PEO) dissolved in the protic ionic liquids ethylammonium nitrate (EAN) and propylammonium nitrate (PAN) and in water. The zero shear viscosity in all three solvents increases with polymer concentration, falling into three concentration regimes corresponding to dilute, semi-dilute and network solutions. Huggins plots reveal three distinct solvent conditions: good (water), good-theta (EAN) and theta (PAN). However, differences in the transition concentrations, power law behaviour of the viscosities, and relaxation times arising from shear thinning in the two ILs can be directly related to the effects of solvent nanostructure.

Surface Mediated Structures: Stabilization of Metastable Polymorphs on the Example of Paracetamol

The preparation of typically thermodynamically unstable polymorphic structures is a challenge. However, solid surfaces are well established aids for the formation and stabilization of polymorphic structures within, for instance, organic electronics. In this study, we report the stabilization of a pharmaceutically relevant substance via a solid surface at ambient conditions. Form III of paracetamol, which is typically unstable in the bulk at standard conditions, can be stabilized with a model silica surface by a standard spin coating procedure followed by rapid heat treatment. Such a preparation technique allows the use of atomic force microscopy and grazing incidence X-ray diffraction measurements revealing detailed information on the morphology and structure of the polymorph. Furthermore, the results exhibit that this polymorph is stable over a long period of time revealing surface mediated stabilization. These findings demonstrate a novel approach to provide thermodynamic stability when applied to similar molecules with specific applications.

Impact of drying on solid state modifications and drug distribution in ibuprofen-loaded calcium stearate pellets.

Drying is a common pharmaceutical process, whose potential to alter the final drug properties-even at relatively low temperatures-is often neglected. The present study addresses the impact of drying at 20 and 50 °C on wet-extruded calcium stearate (CaSt) pellets. Drying at 20 °C caused the majority of ibuprofen to accumulate at the pellet surface due to a strong convective flow from the pellets center to the surface. In contrast, pellets dried at 50 °C still contained ibuprofen in the pellets interior due to the higher drying rate and the associated film breakage during drying. Moreover, the higher drying temperature caused CaSt to form a second lamellar phase and ibuprofen to convert (partly) into its amorphous state. Overall, the drying process affected the solid state and the spatial ibuprofen distribution within the pellet. Knowledge of these effects can aid in tailoring advanced multipellet formulations.

Morphologies in Solvent-Annealed Clotrimazole Thin Films Explained by Hansen-Solubility Parameters.

The induction of different crystal morphologies is of crucial importance for many applications. In this work, the preparation of various crystal morphologies within clotrimazole films on glass substrates is demonstrated. Amorphous clotrimazole thin films were transformed via vapor annealing into crystalline structures; highly monodisperse/multidisperse crystallites, spherulite, or dendritic structures were obtained as the solvent was exchanged. X-ray diffraction experiments reveal that the same polymorph is present for all samples but with varying texture. The achieved morphologies are explained in terms of Hansen-solubility parameters and vapor pressures; thus, the different morphologies and crystal orientations can be explained by solvent—solid interaction strengths within the thin film samples.

Interactions of adsorbed poly(ethylene oxide) mushrooms with a bare silica-ionic liquid interface

The interaction of adsorbed poly(ethylene oxide) (PEO) mushrooms with clean silica-ethylammonium nitrate (EAN, a protic ionic liquid) interfaces is investigated using atomic force microscopy (AFM). 10 kDa, 35 kDa and 100 kDa PEO was used to prepare polymer layers ex situ by drop casting from 0.01 wt% EAN solutions. AFM tapping mode measurements of dried, solvent free PEO layers revealed oblate structures, which increase in size with molecular weight. Colloid probe force curve measurements of these surfaces re-solvated with EAN suggest PEO adopts a mushroom morphology, with the interaction range (layer thickness) increasing with molecular weight. Attractive forces on approach and single strand stretching forces on retraction show PEO has a strong affinity for the silica-EAN interface. The single polymer strand stretching forces follow the freely jointed chain model under good solvent conditions. Contour lengths close to the theoretical limits of 120 nm for the 10 kDa, 290 nm for the 35 kDa and 1240 nm for the 100 kDa PEO samples are observed, while fitted Kuhn lengths are small, at 0.14 nm.