P. K. Day

BICEP2 II: Experiment and Three-Year Data Set

We report on the design and performance of the BICEP2 instrument and on its three-year data set. BICEP2 was designed to measure the polarization of the cosmic microwave background (CMB) on angular scales of 1°-5°(l = 40-200), near the expected peak of the B-mode polarization signature of primordial gravitational waves from cosmic inflation. Measuring B-modes requires dramatic improvements in sensitivity combined with exquisite control of systematics. The BICEP2 telescope observed from the South Pole with a 26 cm aperture and cold, on-axis, refractive optics. BICEP2 also adopted a new detector design in which beam-defining slot antenna arrays couple to transition-edge sensor (TES) bolometers, all fabricated on a common substrate. The antenna-coupled TES detectors supported scalable fabrication and multiplexed readout that allowed BICEP2 to achieve a high detector count of 500 bolometers at 150 GHz, giving unprecedented sensitivity to B-modes at degree angular scales. After optimization of detector and readout parameters, BICEP2 achieved an instrument noise-equivalent temperature of

Experimental evidence for a surface distribution of two-level systems in superconducting lithographed microwave resonators

15.8\ \mu \mathrm{K}\sqrt{\mathrm{s}}

Titanium nitride films for ultrasensitive microresonator detectors

. The full data set reached Stokes Q and U map depths of 87.2 nK in square-degree pixels (5farcm2 μK) over an effective area of 384 deg2 within a 1000 deg2 field. These are the deepest CMB polarization maps at degree angular scales to date. The power spectrum analysis presented in a companion paper has resulted in a significant detection of B-mode polarization at degree scales.

Noise properties of superconducting coplanar waveguide microwave resonators

We present measurements of the temperature-dependent frequency shift of five niobium superconducting coplanar waveguide microresonators with center strip widths ranging from 3 to 50 µm, taken at temperatures in the range of 100–800 mK, far below the 9.2 K transition temperature of niobium. These data agree well with the two-level system (TLS) theory. Fits to this theory provide information on the number of TLSs that interact with each resonator geometry. The geometrical scaling indicates a surface distribution of TLSs and the data are consistent with a TLS surface layer thickness of the order of a few nanometers, as might be expected for a native oxide layer.

Position sensitive x-ray spectrophotometer using microwave kinetic inductance detectors

Titanium nitride (TiNx) films are ideal for use in superconducting microresonator detectors for the following reasons: (a) the critical temperature varies with composition (0 107) and have noise properties similar to resonators made using other materials, while the quasiparticle lifetimes are reasonably long, 10–200 μs. TiN microresonators should therefore reach sensitivities well below 10−19 W Hz−1/2.

Position and energy-resolved particle detection using phonon-mediated microwave kinetic inductance detectors

The authors have measured noise in thin-film superconducting coplanar waveguide resonators. This noise appears entirely as phase noise, equivalent to a jitter of the resonance frequency. In contrast, amplitude fluctuations are not observed at the sensitivity of their measurement. The ratio between the noise power in the phase and amplitude directions is large, in excess of 30 dB. These results have important implications for resonant readouts of various devices such as detectors, amplifiers, and qubits. They suggest that the phase noise is due to two-level systems in dielectric materials.

Antenna-coupled TES bolometers used in BICEP2, Keck Array, and SPIDER

The surface impedance of a superconductor changes when energy is absorbed and Cooper pairs are broken to produce single electron (quasiparticle) excitations. This change may be sensitively measured using a thin-film resonant circuit called a microwave kinetic inductance detector (MKID). The practical application of MKIDs for photon detection requires a method of efficiently coupling the photon energy to the MKID. The authors present results on position sensitive x-ray detectors made by using two aluminum MKIDs on either side of a tantalum photon absorber strip. Diffusion constants, recombination times, and energy resolution are reported. MKIDs can easily be scaled into large arrays.

Real time quasiparticle tunneling measurements on an illuminated quantum capacitance detector

We demonstrate position and energy-resolved phonon-mediated detection of particle interactions in a silicon substrate instrumented with an array of microwave kinetic inductance detectors (MKIDs). The relative magnitude and delay of the signal received in each sensor allows the location of the interaction to be determined with < 1 mm precision at 30 keV. Using this position information, variations in the detector response with position can be removed, and an energy resolution of \sigma_E = 0.55 keV at 30 keV was measured. Since MKIDs can be fabricated from a single deposited film and are naturally multiplexed in the frequency domain, this technology can be extended to provide highly-pixelized athermal phonon sensors for ~1 kg scale detector elements. Such high-resolution, massive particle detectors would be applicable to next-generation rare-event searches such as the direct detection of dark matter, neutrinoless double-beta decay, or coherent neutrino-nucleus scattering.

Quantum capacitance detector: A pair-breaking radiation detector based on the single Cooper-pair box

We have developed antenna-coupled transition-edge sensor bolometers for a wide range of cosmic microwave background (CMB) polarimetry experiments, including Bicep2, Keck Array, and the balloon borne Spider. These detectors have reached maturity and this paper reports on their design principles, overall performance, and key challenges associated with design and production. Our detector arrays repeatedly produce spectral bands with 20%–30% bandwidth at 95, 150, or 230 GHz. The integrated antenna arrays synthesize symmetric co-aligned beams with controlled side-lobe levels. Cross-polarized response on boresight is typically

The fluctuation-imposed limit for temperature measurement

\sim 0.5\%