Parikshit Goswami

Controlled Morphology and Mechanical Characterisation of Electrospun Cellulose Acetate Fibre Webs

The purpose was to interpret the varying morphology of electrospun cellulose acetate (CA) fibres produced from single and binary solvent systems based on solubility parameters to identify processing conditions for the production of defect-free CA fibrous webs by electrospinning. The Hildebrand solubility parameter () and the radius of the sphere in the Hansen space () of acetone, acetic acid, water, N,N-dimethylacetamide (DMAc), methanol, and chloroform were examined and discussed for the electrospinning of CA. The Hildebrand solubility parameter () of acetone and DMAc were found to be within an appropriate range for the dissolution of CA. The suitability of the binary solvent system of acetone: DMAc (2 : 1) for the continuous electrospinning of defect-free CA fibres was confirmed. Electrospun webs exhibited improved tensile strength and modulus after heat and alkali treatment (deacetylation) of the as-spun material, and no major fibre morphological degradation occurred during the deacetylation process.

Optimizing the Colour and Fabric of Targets for the Control of the Tsetse Fly Glossina fuscipes fuscipes

Background Most cases of human African trypanosomiasis (HAT) start with a bite from one of the subspecies of Glossina fuscipes. Tsetse use a range of olfactory and visual stimuli to locate their hosts and this response can be exploited to lure tsetse to insecticide-treated targets thereby reducing transmission. To provide a rational basis for cost-effective designs of target, we undertook studies to identify the optimal target colour. Methodology/Principal Findings On the Chamaunga islands of Lake Victoria , Kenya, studies were made of the numbers of G. fuscipes fuscipes attracted to targets consisting of a panel (25 cm square) of various coloured fabrics flanked by a panel (also 25 cm square) of fine black netting. Both panels were covered with an electrocuting grid to catch tsetse as they contacted the target. The reflectances of the 37 different-coloured cloth panels utilised in the study were measured spectrophotometrically. Catch was positively correlated with percentage reflectance at the blue (460 nm) wavelength and negatively correlated with reflectance at UV (360 nm) and green (520 nm) wavelengths. The best target was subjectively blue, with percentage reflectances of 3%, 29%, and 20% at 360 nm, 460 nm and 520 nm respectively. The worst target was also, subjectively, blue, but with high reflectances at UV (35% reflectance at 360 nm) wavelengths as well as blue (36% reflectance at 460 nm); the best low UV-reflecting blue caught 3× more tsetse than the high UV-reflecting blue. Conclusions/Significance Insecticide-treated targets to control G. f. fuscipes should be blue with low reflectance in both the UV and green bands of the spectrum. Targets that are subjectively blue will perform poorly if they also reflect UV strongly. The selection of fabrics for targets should be guided by spectral analysis of the cloth across both the spectrum visible to humans and the UV region.

Investigation into the potential use of poly(vinyl alcohol)/methylglyoxal fibres as antibacterial wound dressing components.

As problems of antibiotic resistance increase, a continuing need for effective bioactive wound dressings is anticipated for the treatment of infected chronic wounds. Naturally derived antibacterial agents, such as Manuka honey, consist of a mixture of compounds, more than one of which can influence antimicrobial potency. The non-peroxide bacteriostatic properties of Manuka honey have been previously linked to the presence of methylglyoxal. The incorporation of methylglyoxal as a functional antibacterial additive during fibre production was explored as a potential route for manufacturing wound dressing components. Synthetic methylglyoxal and poly(vinyl alcohol) were fabricated into webs of sub-micron fibres by means of electrostatic spinning of an aqueous spinning solution. Composite fabrics were also produced by direct deposition of the poly(vinyl alcohol)–methylglyoxal fibres onto a preformed spunbonded nonwoven substrate. Attenuated total reflectance fourier transform infrared and proton nuclear magnetic resonance spectroscopies confirmed the presence of methylglyoxal within the resulting fibre structure. The antibacterial activity of the fibres was studied using strains of Staphylococcus aureus and Escherichia coli. Strong antibacterial activity, as well as diffusion of methylglyoxal from the fibres was observed at a concentration of 1.55 mg/cm2.

Antibacterial properties of nonwoven wound dressings coated with Manuka honey or methylglyoxal

Manuka honey (MH) is used as an antibacterial agent in bioactive wound dressings via direct impregnation onto a suitable substrate. MH provides unique antibacterial activity when compared with conventional honeys, owing partly to one of its constituents, methylglyoxal (MGO). Aiming to investigate an antibiotic-free antimicrobial strategy, we studied the antibacterial activity of both MH and MGO (at equivalent MGO concentrations) when applied as a physical coating to a nonwoven fabric wound dressing. When physically coated on to a cellulosic hydroentangled nonwoven fabric, it was found that concentrations of 0.0054 mg cm−2 of MGO in the form of MH and MGO were sufficient to achieve a 100 colony forming unit % bacteria reduction against gram-positive Staphylococcus aureus and gram-negative Klebsiella pneumoniae, based on BS EN ISO 20743:2007. A 3- to 20-fold increase in MGO concentration (0.0170–0.1 mg cm−2) was required to facilitate a good antibacterial effect (based on BS EN ISO 20645:2004) in terms of zone of inhibition and lack of growth under the sample. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) was also assessed for MGO in liquid form against three prevalent wound and healthcare-associated pathogens, i.e., Staphylococcus aureus, gram-negative Pseudomonas aeruginosa and gram-positive Enterococcus faecalis. Other than the case of MGO-containing fabrics, solutions with much higher MGO concentrations (128 mg L−1–1024 mg L−1) were required to provide either a bacteriostatic or bactericidal effect. The results presented in this study therefore demonstrate the relevance of an MGO-based coating as an environmentally friendly strategy for the design of functional dressings with antibiotic-free antimicrobial chemistries.

A structurally self-assembled peptide nano-architecture by one-step electrospinning

Self-assembling peptides (SAPs) have been shown to offer great promise in therapeutics and have the ability to undergo self-assembly and form ordered nanostructures. However SAP gels are often associated with inherent weak and transient mechanical properties and incorporation of them into polymeric matrices is a route to enhance their mechanical stability. The aim of this work was to incorporate P11-8 peptide (CH3COQQRFOWOFEQQNH2) within poly(ε-caprolactone) (PCL) fibrous webs via one-step electrospinning, aiming to establish the underlying relationships between spinning process, molecular peptide conformation, and material internal architecture. Electrospinning of PCL solutions (6% w/w) in hexafluoro-2-propanol (HFIP) containing up to 40 mg mL-1 P11-8 resulted in the formation of fibres in both nano- (10-100 nm) and submicron range (100-700 nm), in contrast to PCL only webs, which displayed a predominantly submicron fibre distribution. FTIR and CD spectroscopy on both PCL/peptide solutions and resulting electrospun webs revealed monomeric and β-sheet secondary conformation, respectively, suggesting the occurrence of peptide self-assembly during electrospinning due to solvent evaporation. The peptide concentration (0 → 40 mg mL-1) was found to primarily affect the internal structure of the fabric at the nano-scale, whilst water as well as cell culture medium contact angles were dramatically decreased. Nearly no cytotoxic response (>90% cell viability) was observed when L929 mouse fibroblasts were cultured in contact with electrospun peptide loaded samples. This novel nanofibrous architecture may be the basis for an interesting material platform for e.g. hard tissue repair, in light of the presence of the self-assembled P11-8 in the PCL fibrous structure.

Enrichment of cellulose acetate nanofibre assemblies for therapeutic delivery of l-tryptophan

The essential amino acid l-tryptophan is naturally present in the body, and is also available as a water soluble dietary supplement. The feasibility of preparing enriched cellulose acetate (CA)-based fibres as a vehicle for therapeutic delivery of such biomolecules was investigated. A new ternary solvent system consisting of acetone: N,N-dimethylacetamide: methanol (2:1:2) has been demonstrated to permit the solution blending of CA with the water soluble l-tryptophan. Nanofibrous webs substantially free of structural defects were continuously produced with mean fibre diameters in the range of 520-1010nm, dependent on process parameters. Morphology and diameter of fibres were influenced by concentration of CA spinning solution, applied voltage and flow rates. The kinetic release profile of l-tryptophan from electrospun CA nanofibres was described by the pseudo-second order kinetic model. Fibres with mean diameter of 720nm provide both the highest initial desorption rate and rate constant, which was partially attributed to the low fibre diameter and high relative surface area, but also the fact that the 720nm fibres produced were the most bead-free, providing diffusion advantages over the fibres with lowest mean diameter (520nm). The feasibility of combining l-tryptophan within fibres provides a promising route for manufacture of transdermal delivery devices.

Role of surface energy and nano-roughness in the removal efficiency of bacterial contamination by nonwoven wipes from frequently touched surfaces

Abstract Healthcare associated infections (HCAIs) are responsible for substantial patient morbidity, mortality and economic cost. Infection control strategies for reducing rates of transmission include the use of nonwoven wipes to remove pathogenic bacteria from frequently touched surfaces. Wiping is a dynamic process that involves physicochemical mechanisms to detach and transfer bacteria to fibre surfaces within the wipe. The purpose of this study was to determine the extent to which systematic changes in fibre surface energy and nano-roughness influence removal of bacteria from an abiotic polymer surface in dry wiping conditions, without liquid detergents or disinfectants. Nonwoven wipe substrates composed of two commonly used fibre types, lyocell (cellulosic) and polypropylene, with different surface energies and nano-roughnesses, were manufactured using pilot-scale nonwoven facilities to produce samples of comparable structure and dimensional properties. The surface energy and nano-roughness of some lyocell substrates were further adjusted by either oxygen (O2) or hexafluoroethane (C2F6) gas plasma treatment. Static adpression wiping of an inoculated surface under dry conditions produced removal efficiencies of between 9.4% and 15.7%, with no significant difference (p < 0.05) in the relative removal efficiencies of Escherichia coli, Staphylococcus aureus or Enterococcus faecalis. However, dynamic wiping markedly increased peak wiping efficiencies to over 50%, with a minimum increase in removal efficiency of 12.5% and a maximum increase in removal efficiency of 37.9% (all significant at p < 0.05) compared with static wiping, depending on fibre type and bacterium. In dry, dynamic wiping conditions, nonwoven wipe substrates with a surface energy closest to that of the contaminated surface produced the highest E. coli removal efficiency, while the associated increase in fibre nano-roughness abrogated this trend with S. aureus and E. faecalis. Plasma modification of the nano-roughness and surface energy of fibres in nonwoven wipes was found to influence the relative removal efficiencies of common bacterial pathogens from model healthcare surfaces under dynamic wiping conditions.

Mechanical Properties of Nonwoven Reinforced Thermoplastic Polyurethane Composites

Reinforcement of flexible fibre reinforced plastic (FRP) composites with standard textile fibres is a potential low cost solution to less critical loading applications. The mechanical behaviour of FRPs based on mechanically bonded nonwoven preforms composed of either low or high modulus fibres in a thermoplastic polyurethane (TPU) matrix were compared following compression moulding. Nonwoven preform fibre compositions were selected from lyocell, polyethylene terephthalate (PET), polyamide (PA) as well as para-aramid fibres (polyphenylene terephthalamide; PPTA). Reinforcement with standard fibres manifold improved the tensile modulus and strength of the reinforced composites and the relationship between fibre, fabric and composite’s mechanical properties was studied. The linear density of fibres and the punch density, a key process variable used to consolidate the nonwoven preform, were varied to study the influence on resulting FRP mechanical properties. In summary, increasing the strength and degree of consolidation of nonwoven preforms did not translate to an increase in the strength of resulting fibre reinforced TPU-composites. The TPU composite strength was mainly dependent upon constituent fibre stress-strain behaviour and fibre segment orientation distribution.

Substitution of PFAS chemistry in outdoor apparel and the impact on repellency performance

Intensifying legislation and increased research on the toxicological and persistent nature of per- and polyfluoroalkyl substances (PFASs) have recently influenced the direction of liquid repellent chemistry use; environmental, social, and sustainability responsibilities are at the crux. Without PFAS chemistry, it is challenging to meet current textile industry liquid repellency requirements, which is a highly desirable property, particularly in outdoor apparel where the technology helps to provide the wearer with essential protection from adverse environmental conditions. Herein, complexities between required functionality, legislation and sustainability within outdoor apparel are discussed, and fundamental technical performance of commercially available long-chain (C8) PFASs, shorter-chain (C6) PFASs, and non-fluorinated repellent chemistries finishes are evaluated comparatively. Non-fluorinated finishes provided no oil repellency, and were clearly inferior in this property to PFAS-finished fabrics that demonstrated good oil-resistance. However, water repellency ratings were similar across the range of all finished fabrics tested, all demonstrating a high level of resistance to wetting, and several non-fluorinated repellent fabrics provide similar water repellency to long-chain (C8) PFAS or shorter-chain (C6) PFAS finished fabrics. The primary repellency function required in outdoor apparel is water repellency, and we would propose that the use of PFAS chemistry for such garments is over-engineering, providing oil repellency that is in excess of user requirements. Accordingly, significant environmental and toxicological benefits could be achieved by switching outdoor apparel to non-fluorinated finishes without a significant reduction in garment water-repellency performance. These conclusions are being supported by further research into the effect of laundering, abrasion and ageing of these fabrics.

Parametric Study of Electrospun Cellulose Acetate in Relation to Fibre Diameter

The objective was to identify the main factors and interactions influencing the fibre diameter in the production of electrospun cellulose acetate (CA) webs. A systematic parameter study was completed for producing electrospun CA fibres that were substantially free of bead defects and the effect of different process parameters during electrospinning CA were evaluated in respect of mean fibre diameter. The experiments were planned using factorial designs. Altogether three parameters, each at three levels, were selected for this study. The results indicate that polymer concentration, voltage and flow rate interact so that the magnitude of any change in the mean fibre diameter is dependent upon the level of the other factors. Furthermore, stable electrospinning conditions for CA were confirmed using an acetone: N, N-dimethylacetamide (DMAc) (2:1) solvent system that minimised the presence of structural defects in the web and promoted uniform fibre diameters.