Paul J. Sheskey

Preliminary Report of the Discovery of a New Pharmaceutical Granulation Process Using Foamed Aqueous Binders

Spray granulation is commonly used to improve the flow of drug formulation powders by adding liquid binders. We have discovered a new granulation process whereby liquid binders are added as aqueous foam. Initial experiments indicate that foam granulations require less binder than spray granulations, less water is added to the powder mass, rates of addition of foam can be greater than rates of addition of sprayed liquids, and foam can be added in a single batch to the surface of the powder mass for incorporation at some later stage in the process. This new process appears to have no detrimental effects on granulate, tablet, or in vitro drug dissolution properties. In addition, the elimination of spray addition reduces the complexity of the process and avoids the plugging problems associated with spray nozzles. Several formulations were successfully scaled up from laboratory scale (1.5 kg) to pilot scale (15 kg). Process control was good and there was no detrimental effect on tablet and drug dissolution properties. This paper also proposes a working hypothesis of the mechanism by which foam granulation operates.

Foam granulation: new developments in pharmaceutical solid oral dosage forms using twin screw extrusion machinery

This paper investigates foam granulation in a twin screw extruder as a new continuous wet granulation technique for pharmaceutical powder drug formulations. Foamed aqueous binder has a reportedly lower soak-to-spread ratio than drop or spray liquid addition in batch granulation. This work demonstrates a twin screw extruder configuration for foam granulation and subsequently compares the new approach against liquid injection in the granulation of α-lactose monohydrate with a methylcellulose binder. Trials were conducted at high powder output rates (20–40 kg/h) and high screw speeds (220–320 RPM) with two screw configurations. Process stability improved with the new technique allowing granulation with less binder. The extruded mass maintained a low exit temperature, being insensitive to operating conditions unlike the liquid injection approach, where temperatures rose significantly as flow rate increased. The particle size distribution by foam granulation reflected a more uniformly wetted mass with larger granule growth noted even for conditions where dry powder exited by liquid injection. Other factors were found similar between the two binder delivery methods such as consumed mechanical energy, as well as fracture strength and compressibility of produced granules.

Effects of Lubricant Level, Method of Mixing, and Duration of Mixing on a Controlled-Release Matrix Tablet Containing Hydroxypropyl Methylcellulose

AbstractThe effects of the lubricant magnesium stearate at different concentrations, mixing shear rates, and mixing times on the tablet properties and drug dissolution from controlled-release matrix tablets containing hydroxypropyl methylcellulose 2208, USP (METHOCEL® K4M Premium) have been studied. Diphenhydramine HCl and hydrochlorothiazide were chosen as the model drugs. Spray-dried hydrous lactose (Fast Flo Lactose-316®) and anhydrous dibasic calcium phosphate (A-TAB®) were chosen as the model excipient/fillers. The impact of magnesium stearate on the mechanical strength of tablets appeared to be dependent on the bonding mechanism of the components of the powder mix. Tablets containing A-TAB, which compacts via a brittle fracture mechanism, were harder and had significantly better friability patterns than those prepared using Fast Flo Lactose-316. The compaction of Fast Flo Lactose-316 appears to be a combination of brittle fracture and plastic deformation. Mixes containing lower levels of lubricant (...

Hot-Melt Granulation in a Twin Screw Extruder: Effects of Processing on Formulations with Caffeine and Ibuprofen

Hot-melt granulation (HMG) by twin screw extrusion is a novel technology for the continuous processing of pharmaceuticals but confidence must still be gained regarding whether the environment affects drug properties. In this preliminary study, granulation was studied for a model product containing lactose monohydrate and active ingredients of differing water solubility, namely ibuprofen versus caffeine. The formulations were granulated at 220 rpm and 100°C with polyethylene glycol binders of differing molecular weights and at concentrations between 6.5% and 20%. In terms of granule properties, the low melting point of ibuprofen had a dominant influence by producing larger, stronger granules, whereas the caffeine products were more comparable to a blank containing no active ingredient. Drug degradation was study by differential scanning calorimetry, X-ray diffraction, and high-pressure liquid chromatography. The only detected change was the dehydration of lactose monohydrate for the caffeine and blank products, whereas the lubricating influence of the ibuprofen protected its granules. The short residence time (∼60 s) was consider to be influential in minimizing damage of the drug despite the high temperature and shear attributed to HMG inside a twin screw extruder.

Novel low-molecular-weight hypromellose polymeric films for aqueous film coating applications

The concentration of hypromellose (HPMC) is known to significantly impact the viscosity of coating solutions. The purpose of this study was to determine the viscosity of novel low-molecular-weight (LMW) HPMC products as a function of polymer concentration. The mechanical properties and water vapor permeability of free films prepared from these novel LMW HPMC polymers were also determined and the results were compared with films prepared with conventional HPMC. Solutions of LMW and conventional HPMC 2910 and 2906 containing up to 40% polyethylene glycol (PEG) 400 were prepared and the viscosities were measured using a Brookfield viscometer. Solutions were then cast onto glass plates and stored at 30°C and 50% relative humidity until films were formed. A Chatillon digital force gauge attached to a motorized test stand was used to quantify the mechanical properties of the films, whereas water vapor permeabilities were determined according to the ASTM E96 M-05 water method. As expected, the novel LMW polymer solutions exhibited significantly lower viscosities than the conventional comparators at equivalent polymer concentrations. Film strength of the LMW materials was lower than films prepared from the conventional HPMC solutions, although this effect was not as evident for the HPMC 2906 chemistry. Increasing concentrations of the plasticizer resulted in decreased tensile strength and Young’s modulus and increased elongation as well as increased water vapor permeability, irrespective of polymer type. No statistical difference was found between the tensile strength to Young’s modulus ratios of the F chemistry LMW and conventional HPMC polymer films.

Influence of filler selection on twin screw foam granulation.

Abstract The influence of filler selection in wet granulation was studied for the novel case where the binder is delivered as an unstable, semi-rigid aqueous foam to an extrusion process. The work primarily examined the impact of differing concentrations of microcrystalline cellulose (Avicel PH® 101) in a formulation with spray-dried α-lactose monohydrate (Flowlac® 100) in regards to wetting and granule nucleation for this relatively new technique known as continuous foam granulation. Foam stability was varied within the work to change its drainage and coarsening behavior atop these powder excipients, by use of different foamable binding agents (METHOCEL™ F4 PLV and METHOCEL™ Premium VLV) as well as by adjusting the foam quality. A static bed penetration test was first used to study the foam behavior in wetting these powders without the processing constraints of an extruder which limit possible liquid-to-solids ratios as well as introduce shear which may complicate interpretation of the mechanism. The test found that the penetration time to saturate these powders decreased as their water absorption capacity increased which in turn decreased the size of the formed nuclei. Differences in the stability of the foamed binder had minimal influence on these attributes of wetting despite its high spread-to-soak behavior. The size of granules produced by extrusion similarly demonstrated sensitivity to the increasing water absorption capacity of the filler and little dependency on foam properties. The different liquid-to-solids ratios required to granulate these different formulations inside the extruder highlighted an evolving concept of powder lubricity for continuous foam granulation.

Effect of Formulation Conditions on Hypromellose Performance Properties in Films Used for Capsules and Tablet Coatings

This study investigated the effects of polymer dispersion and hydration conditions on hypromellose (HPMC) film properties, such as strength, oxygen permeability, water vapor transmission, clarity, and haze. The focus of the study was to build a better understanding of the impact that changes to HPMC dispersion and hydration conditions have on performance properties of the resulting films. This understanding could potentially lead to more flexible formulation guidelines for formulators. Films of HPMC 2906 (USP) were produced from aqueous solutions prepared using various formulation conditions. Results showed that tensile properties and oxygen permeability were not significantly affected by the variables used. The differences observed in water vapor transmission are unlikely to affect practical application of the material. However, the differences observed in clarity and haze at 50°C hydration temperature could affect the appearance of a capsule or coated tablet. Several methods were used to determine whether loss of optical properties was due to surface phenomena or bulk defects within a film. Results indicated that the cloudy appearance was primarily due to surface roughness. Based on this information, there is some flexibility in formulation conditions; however, hydration temperatures greater than 25°C are not recommended.