Paul S. Olin

Bond strength of six dentinal adhesives

This study compared the shear bond strengths on dentine of five dentine adhesives against Scotchbond 2 as a control. Dentine specimens from 225 extracted human permanent molar teeth were used in a matched-pair design, such that 45 tooth sides were treated along with the matching control for each of the five test materials. Shear bond strength testing was conducted 24 h after the completion of each specimen. Results showed that mean force (MPa) for the materials were: XR Bond, 17.1 +/- 5.1; Scotchbond Multi-Purpose, 15.9 +/- 6.5; Syntac, 13.5 +/- 8.6; All-Bond 2, 6.2 +/- 4.1; Scotchbond 2 (control composite score), 4.9 +/- 3.0; Denthesive, 3.4 +/- 1.7. Matched pair t-test comparisons with Scotchbond 2 control were: XR Bond, P = 0.0005; Scotchbond Multi-Purpose, P = 0.0005; Syntac, P = 0.0005; All-Bond 2, P = 0.0368; Denthesive, P = 0.005. Analysis of variance determined a statistically significant difference (P = 0.05) between the means of the bond strengths, which fell into four groups: Group A, XR Bond and Scotchbond Multi-Purpose; Group B, Syntac; Group C, All-Bond 2 and Scotchbond 2; Group D, Scotchbond 2 and Denthesive. In Group C, there was no significant difference between Scotchbond 2 and All-Bond 2. In Group D there was no significant difference between Scotchbond 2 and Denthesive, however, there was significant difference between All-Bond 2 and Denthesive. It was concluded that XR Bond and Scotchbond Multi-Purpose had significantly better shear bond strength than the other dentine adhesives.

Bond strength of a light-cured and two auto-cured glass ionomer liners.

Ninety-nine extracted human molar teeth were used in this study comparing the shear bond strengths on dentine of one light-cured and two auto-cured polyalkenoate (glass ionomer) cements. Bond strength can be influenced by differences in tooth structure. A balanced-incomplete block design (Hull and Nie, 1981) was used to reduce variation attributable to such differences. Cements were applied to paired dentine surfaces in combinations such that 66 tooth sides were treated with each material. A light-cured dentinal adhesive and composite resin restorative material were then placed and shear bond strength testing was conducted exactly 24 h after the completion of each specimen. Mean forces (MPa) for the three materials were compared using an appropriate analysis of variance model (balanced-incomplete-blocks) The shear bond strengths (MPa) of the light-cured liner (Espe, Seefeld/Oberbay, FRG) was 4.71 +/- 1.16. Vitrabond showed the greatest variance of all three materials tested, however this materials average bond strength was greater than the maximum achieved for the other materials. Student-Newman-Keuls comparison of means showed that all cements differed significantly from each other (alpha = 0.05). It is concluded that the light-cured glass ionomer liner exhibited significantly better shear bond strength performance than the two auto-cured glass ionomers tested.

Initial stability measurement of dental implants placed in different anatomical regions of fresh human cadaver jawbone

STATEMENT OF PROBLEM Initial implant stability has been used as an indicator for future osseointegration and whether an immediate/early loading protocol should be applied. However, differences in initial stability in relation to anatomical regions of jawbone have not been studied extensively because of the risks involved with stability measurements. PURPOSE The purpose of this study was to determine whether initial implant stability varies with anatomical regions of the jawbone. MATERIAL AND METHODS Four pairs of edentulous maxillae and mandibles were retrieved from fresh human cadavers. Six implants (Biomet 3i) per pair were placed in different anatomical regions (maxillary anterior, right and left maxillary posterior, mandibular anterior, right and left mandibular posterior). Immediately after implant placement, initial implant stability was measured with a custom-made resonance frequency analyzer, a commercial resonance frequency analysis device (Osstell), and a mechanical tapping device (Periotest). All implant surgeries and initial stability measurements were performed within 72 hours of death to simulate a clinical setting. Repeated measures ANOVA (alpha=.05) and univariate correlation analyses were used to analyze the data. RESULTS Mandibular implants had significantly higher initial stability than maxillary implants. Posterior maxillary implants were least stable. Stability was less buccolingually than mesiodistally. The measurements from 3 stability measuring devices were strongly associated with each other. CONCLUSIONS Initial implant stability varied among anatomical regions of jawbone. Rank of Periotest value and implant stability quotient (Osstell) had the highest correlation (r=-0.852).

Dimensional stability of a polyvinylsiloxane impression material following ethylene oxide and steam autoclave sterilization.

Polyvinlsiloxane impressions were made from a stainless steel master die machined to stimulate five full veneer crown preparations symmetrically placed in an arch form. Three groups of 10 impressions each were made. Treatment groups were sterilized using an ethylene oxide gas and a conventional steam autoclave. Casts were poured and intrapreparation, height, and diameter measurements were made using a stereomicroscope, a digital electronic caliper, and a 1-inch travel dial indicator. Analysis of dimensional changes for the two groups showed that casts made from impressions sterilized by ethylene oxide are acceptable for use in the construction of fixed or removable prostheses. Casts made from impressions sterilized in a steam autoclave can be used for the fabrication of diagnostic casts and some transitional prostheses, but not for routine construction of crowns or fixed partial dentures.

The effects of sterilization on addition silicone impressions in custom and stock metal trays

Five groups of addition silicone impressions (four made in custom autopolymerizing acrylic resin trays and one in stock metal rim-lock trays) were made of a stainless-steel master die. The first group (control group) was not sterilized. The second group was sterilized in an ethylene oxide gas autoclave, the third group in a steam autoclave, and the fourth and fifth groups by immersion for 12 hours in 2% glutaraldehyde. Casts made from each sterilization group were found to be significantly different from control impressions by multivariate analysis of variance and should not be used to fabricate prostheses.

Effect of prolonged ultrasonic instrumentation on the retention of cemented cast crowns

Occasionally the need arises to remove restorations that have been cemented. Several ultrasonic tips have been developed to aid in removing cemented restorations. Earlier studies of the effects of ultrasonic vibration reveal detrimental effects on amalgam surface and marginal integrity and, at short instrumentation periods (2.5 minutes) in vitro, no significant effect on the retention of cemented cast crowns. Twenty identically machined metal dies had nonprecious crowns waxed, cast, and fitted. Each casting was cemented twice with glass ionomer and zinc phosphate cement. Each cement was tested for the effects of vibration on retention. The cements were mixed according to manufacturers specifications, placed under 5 kg load, then placed in 37 degrees C water and contained in a humidor. Retention was tested with a 4202 Instron machine to determine the forces needed to overcome retention. Retention ranged from a high of 125.36 kg for glass ionomer without vibration to a low of 19.11 kg for zinc phosphate vibrated for 12 minutes. The use of vibration is considered an advantageous adjunct to other cast restoration removal devices.

Prevalence of Sinus Augmentation Associated With Maxillary Posterior Implants

Pneumatization of the maxillary sinus limits the quantity of alveolar bone available for implant placement and may result in a lack of primary stability and difficulty in achieving osseointegration. The purpose of this study was to retrospectively analyze a group of patients who had implants placed in the posterior maxilla, calculate the prevalence of sinus augmentation, and identify factors related to sinus augmentation. With institutional review board approval, dental records from a population of patients who had implants placed in the maxillary posterior region between January 2000 and December 2004 were used to create a database. Independent variables were classified as continuous (age of the patient at stage 1 implant surgery [S1], time between extraction and S1, time between extraction and sinus augmentation, and time between sinus augmentation and S1) and categorical (gender, implant failure, American Society of Anesthesiologists system classification, smoking, osteoporosis, residual crestal bone height, implant position, implant proximity, prostheses type, and implant diameter and length). The dependent variable was the incidence of a sinus augmentation procedure. Simple logistic regression was used to assess the influence of each factor on the presence of sinus augmentation (P < .05). The final database included 502 maxillary posterior implants with an overall survival rate of 93.2% over a mean follow-up period of 35.7 months. Of 502 implants, 272 (54.2%) were associated with a sinus augmentation procedure. Among variables, residual crestal bone height (P < .001), implant position (P < .001), implant proximity (P < .001), prosthesis type (P < .001), implant failure (P < .01), and implant diameter (P < .01), were statistically associated with sinus augmentation. Within the limitations of this retrospective study, the results suggest that more than half (54.2%) of the maxillary posterior implants were involved with a sinus augmentation procedure. The prevalence of sinus augmentation increased with decreased residual crestal bone height, more posterior implant locations, and complete or partial edentulism. Sinus augmentation was significantly associated with implant failure and wide implants.

Effects of lubrication on the retention of tapered and parallel cast post and cores

The effects of lubrication on the retention of parallel-sided and tapered cast post and cores cemented with zinc phosphate-cement (ZnPO4) and glass ionomer cements were investigated. Seventy-two maxillary canine teeth of similar size were selected for direct, parallel-sided post and core castings. The canines were sectioned at the cementoenamel junction and mounted in resin blocks. A post space was prepared to 1.5 mm (d) x 10 mm (I) with a handpiece mounted in a surveyor. The teeth were divided into four groups: ZnPO4 without lubricant, ZnPO4 with lubricant rinsed with water, ZnPO4 with lubricant removed by solvent, and ZnPO4 with solvent alone. The same four groups were made by using glass ionomer cement. Retention was tested with a 4200 series Instron machine by pulling the castings out of the teeth. There were no significant differences in retention among the eight groups of parallel posts at alpha = 0.05. The testing procedure was repeated by using an 11 mm post with 6 degrees of taper. With tapered posts, a statistically significant reduction in retention was found in the lubricated samples when compared to the nonlubricated samples.

Improved pontic/tissue relationships using porous coralline hydroxyapatite block.

Porous coralline hydroxyapatite blocks were implanted in the anterior region of several patients to improve the pontic/ridge relationship for a fixed prosthesis, thereby improving esthetic appearance and oral hygiene performance. A beveled incision on the palate was used to displace the flap coronofacially without leaving an area of denuded bone or graft. Flap margins were sutured to the adjacent palatal tissues. At the 2 1/2- and 3-year postgrafting follow-up, the implant area was healthy and ridge contours have been maintained. The permanent fixed partial denture is functional, and radiographic evaluation indicates the continued presence of the porous coralline hydroxyapatite implant. Three-year results have been promising enough to warrant continuing the procedure in patients requiring localized ridge augmentation.

Current prosthodontic practice: A dental laboratory survey

A survey was distributed to dental laboratory owners at the 1988 annual meeting of the Minnesota Dental Laboratory Association. Current laboratory practice in infection control, the use of nonprecious alloys, the amount of time devoted to complete removable prosthodontics, and complete denture laboratory techniques were surveyed. Responses indicate a moderate level of awareness and compliance with infection control techniques recommended by the American Dental Association, a declining demand for removable prosthodontic services, a high percentage of use of nonprecious alloys, and a very high rate of porcelain occlusion requested by dental practitioners. Comparisons with other laboratory surveys and the implications of these results for undergraduate education in prosthodontics are discussed.