Peter C. King

Cold spray metal embedment: an innovative antifouling technology

The study demonstrates that embedment of copper particles into thermoplastic polymers (polymers) using cold spray technology is an effective deterrent against fouling organisms. Two polymers, high-density polyethylene (HDPE) and nylon were metallised with copper powder using cold spray technology. After 250 days in the field, Cu-embedded HDPE and copper plate controls were completely free of hard foulers compared to Cu-embedded nylon and polymer controls which were heavily fouled with both soft and hard fouling. Antifouling (AF) success is related to the interaction between the properties of the polymers (elastic modulus and hardness) and the cold spray process which affect particle embedment depth, and subsequently, the release of copper ions as determined by analytical techniques. Embedding metal using cold spray equipment is shown to be an effective AF technology for polymers, in particular those that are difficult to treat with standard AF coatings, with efficacy being a function of the interaction between the cold spray metal and the polymer recipient.

Polyurethane seismic streamer skins: an application of cold spray metal embedment

Cold spray metal embedment is an innovative antifouling (AF) technology that delivers metal particles with AF properties into many thermoplastic polymers. AF efficacy was quantified for low (22.1 ± 4.8 g m−2) and high (101.1 ± 10.8 g m−2) densities of copper particles embedded into polyurethane (PU) seismic streamer skins, which are used in geophysical exploration. Failure of each Cu-embedded treatment was defined as settlement of hard foulers. Low-density streamers failed after 42 days while high-density streamers failed after 210 days. Most importantly, the high-density streamers were completely free of hard foulers including the barnacle Amphibalanus reticulatus during this time period. In conclusion, cold-spray metal embedment is an effective AF technology for PU seismic streamer skins, under intense fouling conditions. Higher copper particle densities enhance AF longevity and the effect of density provides a tool to extend efficacy and enhance AF performance for specific polymers.

Characterisation of Cold Spray Titanium Coatings

Cold spray is a solid state spray deposition process utilizing a supersonic De Laval nozzle to accelerate fine particles to high velocities. Particles plastically deform on impact to the substrate and to each other to create dense well adhered structures. In this study, the microstructure and mechanical properties of cold spray Titanium coatings deposited using nitrogen gas at different gas temperature and pressure were examined. In general, it was found that gas-atomised CP-titanium powder is capable of producing dense coating structures on aluminium alloy (Al6061) substrates. The micro-hardness, oxygen and nitrogen content of the coatings were found to be slightly higher than powder in the as-received condition. It was also found the coating residual stress was purely compressive when cold spray is conducted at high gas pressure and temperature.

Assessing the antifouling properties of cold-spray metal embedment using loading density gradients of metal particles

Particles of copper, bronze and zinc were embedded into a polymer using cold-spray technology to produce loading density gradients of metal particles. The gradients were used to identify the species with the highest tolerance to the release of copper and zinc ions. The gradients also established the minimum effective release rates (MERRs) of copper and zinc ions needed to prevent the recruitment of fouling under field conditions. Watersipora sp. and Simplaria pseudomilitaris had the highest tolerances to the release of metal ions. Copper and bronze gradient tubes were similar in their MERRs of copper ions against Watersipora sp. (0.058 g m−2 h−1 and 0.054 g m−2 h−1, respectively) and against S. pseudomilitaris (0.030 g m−2 h−1 and 0.025 g m−2 h−1, respectively). Zinc was not an effective antifoulant, with failure within two weeks. In conclusion, cold-spray gradients were effective in determining MERRs and these outcomes provide the basis for the development of cold-spray surfaces with pre-determined life-spans using controlled MERRs.

Utilization of Titanium Particle Impact Location to Validate a 3D Multicomponent Model for Cold Spray Additive Manufacturing

Cold spray is a solid-state rapid deposition technology in which metal powder is accelerated to supersonic speeds within a de Laval nozzle and then impacts onto the surface of a substrate. It is possible for cold spray to build thick structures, thus providing an opportunity for melt-less additive manufacturing. Image analysis of particle impact location and focused ion beam dissection of individual particles were utilized to validate a 3D multicomponent model of cold spray. Impact locations obtained using the 3D model were found to be in close agreement with the empirical data. Moreover, the 3D model revealed the particles’ velocity and temperature just before impact—parameters which are paramount for developing a full understanding of the deposition process. Further, it was found that the temperature and velocity variations in large-size particles before impact were far less than for the small-size particles. Therefore, an optimal particle temperature and velocity were identified, which gave the highest deformation after impact. The trajectory of the particles from the injection point to the moment of deposition in relation to propellant gas is visualized. This detailed information is expected to assist with the optimization of the deposition process, contributing to improved mechanical properties for additively manufactured cold spray titanium parts.