Peter Samora Owuor

Role of Atomic Layer Functionalization in Building Scalable Bottom-Up Assembly of Ultra-Low Density Multifunctional Three-Dimensional Nanostructures

Building three-dimensional (3D) structures from their constituent zero-, one-, and two-dimensional nanoscale building blocks in a bottom-up assembly is considered the holey grail of nanotechnology. However, fabricating such 3D nanostructures at ambient conditions still remains a challenge. Here, we demonstrate an easily scalable facile method to fabricate 3D nanostructures made up of entirely zero-dimensional silicon dioxide (SiO2) nanoparticles. By combining functional groups and vacuum filtration, we fabricate lightweight and highly structural stable 3D SiO2 materials. Further synergistic effect of material is shown by addition of a 2D material, graphene oxide (GO) as reinforcement which results in 15-fold increase in stiffness. Molecular dynamics (MD) simulations are used to understand the interaction between silane functional groups (3-aminopropyl triethoxysilane) and SiO2 nanoparticles thus confirming the reinforcement capability of GO. In addition, the material is stable under high temperature and offers a cost-effective alternative to both fire-retardant and oil absorption materials.

Hybrid MoS2/h-BN Nanofillers As Synergic Heat Dissipation and Reinforcement Additives in Epoxy Nanocomposites

Two-dimensional (2D) nanomaterials as molybdenum disulfide (MoS2), hexagonal boron nitride (h-BN), and their hybrid (MoS2/h-BN) were employed as fillers to improve the physical properties of epoxy composites. Nanocomposites were produced in different concentrations and studied in their microstructure, mechanical and thermal properties. The hybrid 2D mixture imparted efficient reinforcement to the epoxy leading to increases of up to 95% in tensile strength, 60% in ultimate strain, and 58% in Youngs modulus. Moreover, an enhancement of 203% in thermal conductivity was achieved for the hybrid composite as compared to the pure polymer. The incorporation of MoS2/h-BN mixture nanofillers in epoxy resulted in nanocomposites with multifunctional characteristics for applications that require high mechanical and thermal performance.

Multiscale Geometric Design Principles Applied to 3D Printed Schwarzites

Schwartzites are 3D porous solids with periodic minimal surfaces having negative Gaussian curvatures and can possess unusual mechanical and electronic properties. The mechanical behavior of primitive and gyroid schwartzite structures across different length scales is investigated after these geometries are 3D printed at centimeter length scales based on molecular models. Molecular dynamics and finite elements simulations are used to gain further understanding on responses of these complex solids under compressive loads and kinetic impact experiments. The results show that these structures hold great promise as high load bearing and impact-resistant materials due to a unique layered deformation mechanism that emerges in these architectures during loading. Easily scalable techniques such as 3D printing can be used for exploring mechanical behavior of various predicted complex geometrical shapes to build innovative engineered materials with tunable properties.

Laminated Object Manufacturing of 3D‐Printed Laser‐Induced Graphene Foams

Laser-induced graphene (LIG), a graphene structure synthesized by a one-step process through laser treatment of commercial polyimide (PI) film in an ambient atmosphere, has been shown to be a versatile material in applications ranging from energy storage to water treatment. However, the process as developed produces only a 2D product on the PI substrate. Here, a 3D LIG foam printing process is developed on the basis of laminated object manufacturing, a widely used additive-manufacturing technique. A subtractive laser-milling process to yield further refinements to the 3D structures is also developed and shown here. By combining both techniques, various 3D graphene objects are printed. The LIG foams show good electrical conductivity and mechanical strength, as well as viability in various energy storage and flexible electronic sensor applications.

Lightweight Hexagonal Boron Nitride Foam for CO2 Absorption

Weak van der Waals forces between inert hexagonal boron nitride (h-BN) nanosheets make it easy for them to slide over each other, resulting in an unstable structure in macroscopic dimensions. Creating interconnections between these inert nanosheets can remarkably enhance their mechanical properties. However, controlled design of such interconnections remains a fundamental problem for many applications of h-BN foams. In this work, a scalable in situ freeze-drying synthesis of low-density, lightweight 3D macroscopic structures made of h-BN nanosheets chemically connected by poly(vinyl alcohol) (PVA) molecules via chemical cross-link is demonstrated. Unlike pristine h-BN foam which disintegrates upon handling after freeze-drying, h-BN/PVA foams exhibit stable mechanical integrity in addition to high porosity and large surface area. Fully atomistic simulations are used to understand the interactions between h-BN nanosheets and PVA molecules. In addition, the h-BN/PVA foam is investigated as a possible CO2 absorption and as laser irradiation protection material.

Bacteria as Bio-Template for 3D Carbon Nanotube Architectures

It is one of the most important needs to develop renewable, scalable and multifunctional methods for the fabrication of 3D carbon architectures. Even though a lot of methods have been developed to create porous and mechanically stable 3D scaffolds, the fabrication and control over the synthesis of such architectures still remain a challenge. Here, we used Magnetospirillum magneticum (AMB-1) bacteria as a bio-template to fabricate light-weight 3D solid structure of carbon nanotubes (CNTs) with interconnected porosity. The resulting porous scaffold showed good mechanical stability and large surface area because of the excellent pore interconnection and high porosity. Steered molecular dynamics simulations were used to quantify the interactions between nanotubes and AMB-1 via the cell surface protein MSP-1 and flagellin. The 3D CNTs-AMB1 nanocomposite scaffold is further demonstrated as a potential substrate for electrodes in supercapacitor applications.

Mechanical Properties of Ultralow Density Graphene Oxide/Polydimethylsiloxane Foams

Low-density, highly porous graphene/graphene oxide (GO) based-foams have shown high performance in energy absorption applications, even under high compressive deformations. In general, foams are very effective as energy dissipative materials and have been widely used in many areas such as automotive, aerospace and biomedical industries. In the case of graphene-based foams, the good mechanical properties are mainly attributed to the intrinsic graphene and/or GO electronic and mechanical properties. Despite the attractive physical properties of graphene/GO based-foams, their structural and thermal stabilities are still a problem for some applications. For instance, they are easily degraded when placed in flowing solutions, either by the collapsing of their layers or just by structural disintegration into small pieces. Recently, a new and scalable synthetic approach to produce low-density 3D macroscopic GO structure interconnected with polydimethylsiloxane (PDMS) polymeric chains (pGO) was proposed. A controlled amount of PDMS is infused into the freeze-dried foam resulting into a very rigid structure with improved mechanical properties, such as tensile plasticity and toughness. The PDMS wets the graphene oxide sheets and acts like a glue bonding PDMS and GO sheets. In order to obtain further insights on mechanisms behind the enhanced mechanical pGO response we carried out fully atomistic molecular dynamics (MD) simulations. Based on MD results, we build up a structural model that can explain the experimentally observed mechanical behavior.

Eco-Friendly Polymer-Layered Silicate Nanocomposite–Preparation, Chemistry, Properties, and Applications

This chapter aims at exploring the revolutionary field of nanotechnology and some of its promising aspects in polymer nanocomposites in view of preparation, characterization, materials properties, and processing of polymer layered silicate nanocomposites. These materials are attracting considerable interest in polymer science research. Polymer layered silicate nanocomposites are an important class of hybrid, organic/inorganic materials with substantially improved mechanical, thermal, and thermomechanical properties in comparison to pristine polymers. In addition, they also show superior ultraviolet (UV) as well as chemical resistance and are widely being investigated for improving gas barrier and flame retardant properties. Hectorite and montmorillonite are among the most commonly used smectite-type layered silicates for the preparation of polymer–clay nanocomposites. Smectites are a valuable mineral class for industrial applications due to their high cation exchange capacities, surface area, surface reactivity, adsorptive properties, and, in the case of hectorite, high viscosity and transparency in solution. A wide range of polymer matrices are explored for the preparation of polymer–clay nanocomposites, however, this chapter deals with special emphasis on biodegradable polymers––cellulose and natural rubber. Also, the chapter describes the common synthetic techniques in producing polymeric layered silicate nanocomposites, its properties, and applications.